Bmw 318i 2003
Model 318i made in 2003 by Bmw got 3 consumer complains there are 17 investigations as well as 6 service bulletins. Consumer complaints with reference, among others things, to engine and engine cooling, exterior lighting and service brakes, hydraulic. Technical service bulletines regarding exterior lighting, steering. The car had one investigation (exterior lighting).
Model 2003
Bulletins
| Bulletin | Bulletin date | Replacement Bulletin | Item no. | Summary | Added |
|---|---|---|---|---|---|
| EXTERIOR LIGHTING | |||||
| SIB-63-02-01 | 08/01/2010 | 10037025 | Ready | 04/27/2011 | |
| SIB-63-02-01 | 08/01/2010 | 10037025 | Bmw: procedure for determining and replacing incandescent and halogen light bulbs under warranty. *rm | 04/27/2011 | |
| STEERING - ELECTRIC POWER ASSIST SYSTEM | |||||
| SIB-32-04-07 | 06/01/2010 | 10036979 | Ready | 04/25/2011 | |
| SIB-32-04-07 | 06/01/2010 | 10036979 | Bmw: a new technical process has been created for bmw to identify causes of steering complaints with a wide range of models. *rm | 04/25/2011 | |
| STEERING - HYDRAULIC POWER ASSIST SYSTEM | |||||
| SIB-32-04-07 | 06/01/2010 | 10036979 | Ready | 04/25/2011 | |
| SIB-32-04-07 | 06/01/2010 | 10036979 | Bmw: a new technical process has been created for bmw to identify causes of steering complaints with a wide range of models. *rm | 04/25/2011 | |
Investigations
| NHTSA ID | Manufacturer | Date open | Date close | Subject | Recall campaign | |
|---|---|---|---|---|---|---|
| EXTERIOR LIGHTING | ||||||
| EA09019 | BMW OF NORTH AMERICA, LLC | 12/18/2009 | 09/28/2011 | Rear Lamp Illumination | 11V438000 | |
| In a letter submitted to the office of defects investigation (odi) dated august25, 2011, bmwindicated that it will conduct a voluntary recall campaign to remedy the subject vehicles.the issue involves the rear lamps in the vehicles body panel.through normal vehicle use over time, the rear lamps ground wiring and associated 8-pin connector can experience an increase of the resistance at the electrical contact points.this can lead to intermittent or permanent loss of the rear lamp functions which include tail, brake, and turn signal operation.the recall consists of modifying the rear lamps in the vehicles body panel by adding a secondary ground connection in parallel to the existing primary ground connection.an 8-pin connector that attaches the primary ground wiring to the rear lamp assembly will also be inspected and replaced if necessary.bmw will complete dealer notification in september 2011 and will begin owner notification in october 2011.all 3 series sedans (except for the m3 sedan which utilized a different rear lamp assembly) that were built between september 1, 2001 and march 1, 2005 are included in this recall, totalling approximately 241,000 vehicles.the action taken by bmw is sufficient to resolve the issues raised by this investigation.accordingly, this investigation is closed. | ||||||
| DP09002 | BAYERISCHE MOTOREN WERKE | 04/08/2009 | 08/06/2009 | REAR LAMP ILLUMINATION | ||
| In march 2009, the office of defects investigation (odi) received a petition from mr. mark peters requesting an investigation of rear lamp failure in model year 2002-2005 bmw 3-series vehicles.an information request letter was sent to bmw in april 2009, and odi received bmw's response in june 2009.the tail lamp assembly contains lighting for the brake lamps, tail lamps, and turn signals.a technical service bulletin (tsb) was issued by bmw in january of 2007 instructing service technicians to examine an 8 pin electrical connector for heat-related damage and to incorporate additional ground wiring to the connector.complainants have alleged that significant thermal damage to the connector and associated ground wiring has occurred.this condition can result in intermittent or total loss of all lighting (brake, tail, and turn signal) for the effected rear lamp assembly.odi will open a preliminary evaluation to further examine this issue including further evaluating bmw complaints and related warranty data. | ||||||
| EA09019 | BAYERISCHE MOTOREN WERKE | 12/18/2009 | REAR LAMP ILLUMINATION | |||
| The outboard rear light assembly consists of a turn signal lamp, a tail lamp and a brake lamp.failure of the light assembly ground circuit results in loss of all three lamps.bmw submitted complaint and warranty information showing a significant number of rear lamp assembly failures due to an open ground connection at the eight pin connector of the light assembly.this results in the loss of the rear turn signal.overheating of the ground circuit electrical pin, possibly due to increased resistance and or high current flow, is indicated in some failures.additionally bmw issued a technical service bulletin (tsb) sib-630306 in february 2007 to address the condition by adding supplementary ground wiring to the tail lamp assembly.the additional ground wire added by the procedure reduces the current flow at the eight pin connector.odi is opening this ea to further investigate the issue. | ||||||
| PE09036 | BAYERISCHE MOTOREN WERKE | 08/07/2009 | 12/22/2009 | REAR LAMP ILLUMINATION | ||
| Odi has received complaints from consumers stating that their tail light assembly is not properly illuminating.the tail light assembly consists of a turn signal lamp, a tail lamp and a brake lamp.the complainants have indicated that the issue is with an 8 pin connector and associated ground wiring.these components are allegedly overheating and melting due to excessive electrical current that runs through the system.bmw issued a technical service bulletin (tsb) sib-630306 on february 2007 to address the condition by adding supplementary ground wiring to the tail lamp assembly.odi is upgrading to an ea to further investigate the issue. | ||||||
| EXTERIOR LIGHTING - BACK UP LIGHTS | ||||||
| DP09002 | BAYERISCHE MOTOREN WERKE | 04/08/2009 | 08/06/2009 | REAR LAMP ILLUMINATION | ||
| In march 2009, the office of defects investigation (odi) received a petition from mr. mark peters requesting an investigation of rear lamp failure in model year 2002-2005 bmw 3-series vehicles.an information request letter was sent to bmw in april 2009, and odi received bmw's response in june 2009.the tail lamp assembly contains lighting for the brake lamps, tail lamps, and turn signals.a technical service bulletin (tsb) was issued by bmw in january of 2007 instructing service technicians to examine an 8 pin electrical connector for heat-related damage and to incorporate additional ground wiring to the connector.complainants have alleged that significant thermal damage to the connector and associated ground wiring has occurred.this condition can result in intermittent or total loss of all lighting (brake, tail, and turn signal) for the effected rear lamp assembly.odi will open a preliminary evaluation to further examine this issue including further evaluating bmw complaints and related warranty data. | ||||||
| EXTERIOR LIGHTING - BRAKE LIGHTS | ||||||
| EA09019 | BMW OF NORTH AMERICA, LLC | 12/18/2009 | 09/28/2011 | Rear Lamp Illumination | 11V438000 | |
| In a letter submitted to the office of defects investigation (odi) dated august25, 2011, bmwindicated that it will conduct a voluntary recall campaign to remedy the subject vehicles.the issue involves the rear lamps in the vehicles body panel.through normal vehicle use over time, the rear lamps ground wiring and associated 8-pin connector can experience an increase of the resistance at the electrical contact points.this can lead to intermittent or permanent loss of the rear lamp functions which include tail, brake, and turn signal operation.the recall consists of modifying the rear lamps in the vehicles body panel by adding a secondary ground connection in parallel to the existing primary ground connection.an 8-pin connector that attaches the primary ground wiring to the rear lamp assembly will also be inspected and replaced if necessary.bmw will complete dealer notification in september 2011 and will begin owner notification in october 2011.all 3 series sedans (except for the m3 sedan which utilized a different rear lamp assembly) that were built between september 1, 2001 and march 1, 2005 are included in this recall, totalling approximately 241,000 vehicles.the action taken by bmw is sufficient to resolve the issues raised by this investigation.accordingly, this investigation is closed. | ||||||
| DP09002 | BAYERISCHE MOTOREN WERKE | 04/08/2009 | 08/06/2009 | REAR LAMP ILLUMINATION | ||
| In march 2009, the office of defects investigation (odi) received a petition from mr. mark peters requesting an investigation of rear lamp failure in model year 2002-2005 bmw 3-series vehicles.an information request letter was sent to bmw in april 2009, and odi received bmw's response in june 2009.the tail lamp assembly contains lighting for the brake lamps, tail lamps, and turn signals.a technical service bulletin (tsb) was issued by bmw in january of 2007 instructing service technicians to examine an 8 pin electrical connector for heat-related damage and to incorporate additional ground wiring to the connector.complainants have alleged that significant thermal damage to the connector and associated ground wiring has occurred.this condition can result in intermittent or total loss of all lighting (brake, tail, and turn signal) for the effected rear lamp assembly.odi will open a preliminary evaluation to further examine this issue including further evaluating bmw complaints and related warranty data. | ||||||
| EA09019 | BAYERISCHE MOTOREN WERKE | 12/18/2009 | REAR LAMP ILLUMINATION | |||
| The outboard rear light assembly consists of a turn signal lamp, a tail lamp and a brake lamp.failure of the light assembly ground circuit results in loss of all three lamps.bmw submitted complaint and warranty information showing a significant number of rear lamp assembly failures due to an open ground connection at the eight pin connector of the light assembly.this results in the loss of the rear turn signal.overheating of the ground circuit electrical pin, possibly due to increased resistance and or high current flow, is indicated in some failures.additionally bmw issued a technical service bulletin (tsb) sib-630306 in february 2007 to address the condition by adding supplementary ground wiring to the tail lamp assembly.the additional ground wire added by the procedure reduces the current flow at the eight pin connector.odi is opening this ea to further investigate the issue. | ||||||
| PE09036 | BAYERISCHE MOTOREN WERKE | 08/07/2009 | 12/22/2009 | REAR LAMP ILLUMINATION | ||
| Odi has received complaints from consumers stating that their tail light assembly is not properly illuminating.the tail light assembly consists of a turn signal lamp, a tail lamp and a brake lamp.the complainants have indicated that the issue is with an 8 pin connector and associated ground wiring.these components are allegedly overheating and melting due to excessive electrical current that runs through the system.bmw issued a technical service bulletin (tsb) sib-630306 on february 2007 to address the condition by adding supplementary ground wiring to the tail lamp assembly.odi is upgrading to an ea to further investigate the issue. | ||||||
| EXTERIOR LIGHTING - TAIL LIGHTS | ||||||
| EA09019 | BMW OF NORTH AMERICA, LLC | 12/18/2009 | 09/28/2011 | Rear Lamp Illumination | 11V438000 | |
| In a letter submitted to the office of defects investigation (odi) dated august25, 2011, bmwindicated that it will conduct a voluntary recall campaign to remedy the subject vehicles.the issue involves the rear lamps in the vehicles body panel.through normal vehicle use over time, the rear lamps ground wiring and associated 8-pin connector can experience an increase of the resistance at the electrical contact points.this can lead to intermittent or permanent loss of the rear lamp functions which include tail, brake, and turn signal operation.the recall consists of modifying the rear lamps in the vehicles body panel by adding a secondary ground connection in parallel to the existing primary ground connection.an 8-pin connector that attaches the primary ground wiring to the rear lamp assembly will also be inspected and replaced if necessary.bmw will complete dealer notification in september 2011 and will begin owner notification in october 2011.all 3 series sedans (except for the m3 sedan which utilized a different rear lamp assembly) that were built between september 1, 2001 and march 1, 2005 are included in this recall, totalling approximately 241,000 vehicles.the action taken by bmw is sufficient to resolve the issues raised by this investigation.accordingly, this investigation is closed. | ||||||
| DP09002 | BAYERISCHE MOTOREN WERKE | 04/08/2009 | 08/06/2009 | REAR LAMP ILLUMINATION | ||
| In march 2009, the office of defects investigation (odi) received a petition from mr. mark peters requesting an investigation of rear lamp failure in model year 2002-2005 bmw 3-series vehicles.an information request letter was sent to bmw in april 2009, and odi received bmw's response in june 2009.the tail lamp assembly contains lighting for the brake lamps, tail lamps, and turn signals.a technical service bulletin (tsb) was issued by bmw in january of 2007 instructing service technicians to examine an 8 pin electrical connector for heat-related damage and to incorporate additional ground wiring to the connector.complainants have alleged that significant thermal damage to the connector and associated ground wiring has occurred.this condition can result in intermittent or total loss of all lighting (brake, tail, and turn signal) for the effected rear lamp assembly.odi will open a preliminary evaluation to further examine this issue including further evaluating bmw complaints and related warranty data. | ||||||
| PE09036 | BAYERISCHE MOTOREN WERKE | 08/07/2009 | 12/22/2009 | REAR LAMP ILLUMINATION | ||
| Odi has received complaints from consumers stating that their tail light assembly is not properly illuminating.the tail light assembly consists of a turn signal lamp, a tail lamp and a brake lamp.the complainants have indicated that the issue is with an 8 pin connector and associated ground wiring.these components are allegedly overheating and melting due to excessive electrical current that runs through the system.bmw issued a technical service bulletin (tsb) sib-630306 on february 2007 to address the condition by adding supplementary ground wiring to the tail lamp assembly.odi is upgrading to an ea to further investigate the issue. | ||||||
| EA09019 | BAYERISCHE MOTOREN WERKE | 12/18/2009 | REAR LAMP ILLUMINATION | |||
| The outboard rear light assembly consists of a turn signal lamp, a tail lamp and a brake lamp.failure of the light assembly ground circuit results in loss of all three lamps.bmw submitted complaint and warranty information showing a significant number of rear lamp assembly failures due to an open ground connection at the eight pin connector of the light assembly.this results in the loss of the rear turn signal.overheating of the ground circuit electrical pin, possibly due to increased resistance and or high current flow, is indicated in some failures.additionally bmw issued a technical service bulletin (tsb) sib-630306 in february 2007 to address the condition by adding supplementary ground wiring to the tail lamp assembly.the additional ground wire added by the procedure reduces the current flow at the eight pin connector.odi is opening this ea to further investigate the issue. | ||||||
| EXTERIOR LIGHTING - TURN SIGNAL | ||||||
| EA09019 | BMW OF NORTH AMERICA, LLC | 12/18/2009 | 09/28/2011 | Rear Lamp Illumination | 11V438000 | |
| In a letter submitted to the office of defects investigation (odi) dated august25, 2011, bmwindicated that it will conduct a voluntary recall campaign to remedy the subject vehicles.the issue involves the rear lamps in the vehicles body panel.through normal vehicle use over time, the rear lamps ground wiring and associated 8-pin connector can experience an increase of the resistance at the electrical contact points.this can lead to intermittent or permanent loss of the rear lamp functions which include tail, brake, and turn signal operation.the recall consists of modifying the rear lamps in the vehicles body panel by adding a secondary ground connection in parallel to the existing primary ground connection.an 8-pin connector that attaches the primary ground wiring to the rear lamp assembly will also be inspected and replaced if necessary.bmw will complete dealer notification in september 2011 and will begin owner notification in october 2011.all 3 series sedans (except for the m3 sedan which utilized a different rear lamp assembly) that were built between september 1, 2001 and march 1, 2005 are included in this recall, totalling approximately 241,000 vehicles.the action taken by bmw is sufficient to resolve the issues raised by this investigation.accordingly, this investigation is closed. | ||||||
| PE09036 | BAYERISCHE MOTOREN WERKE | 08/07/2009 | 12/22/2009 | REAR LAMP ILLUMINATION | ||
| Odi has received complaints from consumers stating that their tail light assembly is not properly illuminating.the tail light assembly consists of a turn signal lamp, a tail lamp and a brake lamp.the complainants have indicated that the issue is with an 8 pin connector and associated ground wiring.these components are allegedly overheating and melting due to excessive electrical current that runs through the system.bmw issued a technical service bulletin (tsb) sib-630306 on february 2007 to address the condition by adding supplementary ground wiring to the tail lamp assembly.odi is upgrading to an ea to further investigate the issue. | ||||||
| EA09019 | BAYERISCHE MOTOREN WERKE | 12/18/2009 | REAR LAMP ILLUMINATION | |||
| The outboard rear light assembly consists of a turn signal lamp, a tail lamp and a brake lamp.failure of the light assembly ground circuit results in loss of all three lamps.bmw submitted complaint and warranty information showing a significant number of rear lamp assembly failures due to an open ground connection at the eight pin connector of the light assembly.this results in the loss of the rear turn signal.overheating of the ground circuit electrical pin, possibly due to increased resistance and or high current flow, is indicated in some failures.additionally bmw issued a technical service bulletin (tsb) sib-630306 in february 2007 to address the condition by adding supplementary ground wiring to the tail lamp assembly.the additional ground wire added by the procedure reduces the current flow at the eight pin connector.odi is opening this ea to further investigate the issue. | ||||||
| DP09002 | BAYERISCHE MOTOREN WERKE | 04/08/2009 | 08/06/2009 | REAR LAMP ILLUMINATION | ||
| In march 2009, the office of defects investigation (odi) received a petition from mr. mark peters requesting an investigation of rear lamp failure in model year 2002-2005 bmw 3-series vehicles.an information request letter was sent to bmw in april 2009, and odi received bmw's response in june 2009.the tail lamp assembly contains lighting for the brake lamps, tail lamps, and turn signals.a technical service bulletin (tsb) was issued by bmw in january of 2007 instructing service technicians to examine an 8 pin electrical connector for heat-related damage and to incorporate additional ground wiring to the connector.complainants have alleged that significant thermal damage to the connector and associated ground wiring has occurred.this condition can result in intermittent or total loss of all lighting (brake, tail, and turn signal) for the effected rear lamp assembly.odi will open a preliminary evaluation to further examine this issue including further evaluating bmw complaints and related warranty data. | ||||||
Consumer Complaints
| Fail date | miles | occurences | Purchase date |
|---|---|---|---|
| ENGINE AND ENGINE COOLING - ENGINE | |||
| 02/15/2003 | 2900 | 1 | |
| Consumer states when vehicle idles it shuts off. dealer states they can't duplicate the problem.*ak | |||
| EXTERIOR LIGHTING - HEADLIGHTS | |||
| 12/31/2003 | 0 | ||
| I was blinded tonight by the high intensity discharge headlights on a car 100 or more feet from me that was coming out of a gas station. i was in a parking lot across the highway from the gas station and becuase o being blinded i didn't see a road divider. my right front wheel hit it a a low speed and blew the tire and bent the rim. obviously the other driver didn't know i existed or had been financially and emotionally impacted by his headlights but it is just a matter of time when some unexplained fatal accident will have the same roots. thank you, dan sternberg | |||
| SERVICE BRAKES, HYDRAULIC - ANTILOCK - ABS WARNING LIGHT | |||
| 01/28/2003 | |||
| Vehicle was parked in driveway when the vehicle rolled out into the street with the emergency brakes on. ph | |||