Bmw E46 2003
Model E46 made in 2003 by Bmw got 5 consumer complains, 12 investigations there is 1 recall as well as 4 service bulletins. Consumer complaints with reference to exterior lighting. . Technical service bulletines regarding electrical system, engine and engine cooling and exterior lighting. The car had one investigation (exterior lighting). There was one recall concerning exterior lighting .
Model 2003
Recalls
| Campaign | Manufacturer | Manufacturing date | Type | # of units affected | Date Owner notified Mfg | Recall Initiated by | Manufacturers of recalled vehicles/products | Report Recieved Date | Record Creation Date | Regulation Part Number | FMVSS Number | |||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| EXTERIOR LIGHTING - HEADLIGHTS | ||||||||||||||||
| 09E025000 | DOPE, INC. | E (Equipment) | 42540 | 07/28/2009 | OVSC | BAYERISCHE MOTOREN WERKE | 05/11/2009 | 05/11/2009 | 571 | 108 | ||||||
| Defect Summary | Dope, inc. is recalling 42,540 combination corner and bumper lamp assemblies of various part numbers sold for use as aftermarket equipment for various passenger vehicles. these headlamps fail to conform to the requirements of federal motor vehicle safety standard no. 108, lamps, reflective devices, and associated equipment. these lamps do not contain the required amber side reflectors. | |||||||||||||||
| Consequence Summary | Decreased lighting visibility may result in a vehicle crash. | |||||||||||||||
| Corrective Summary | Dope, inc. will notify owners and offer a full refund for the noncompliant combination lamps. the safety recall began on july 28, 2009. owners may contact dope, inc. at 1-626-272-1798. | |||||||||||||||
| Notes | This recall only pertains to aftermarket replacement equipment and has no relation to any original equipment installed on vehicles produced by the vehicle manufacturer.in order to determine if your aftermarket lamp assembly is affected by this noncompliance, please review the list of model numbers provided to us by dope, inc.the list can be found under document search located at the bottom of your screen. owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov . | |||||||||||||||
Bulletins
| Bulletin | Bulletin date | Replacement Bulletin | Item no. | Summary | Added |
|---|---|---|---|---|---|
| ELECTRICAL SYSTEM - SOFTWARE | |||||
| SI-B12-22-08 | 10/01/2009 | 10032574 | Bmw: voluntary emissions recall 08e-a03; m3 s54-dme reprogramming for catalyst conversion diagnosis. the dme programming, as originally installed, may cause the obd diagnostic to erroneously evaluate the efficiency of the catalytic conver | 04/14/2010 | |
| ENGINE AND ENGINE COOLING - EXHAUST SYSTEM - EMISSION CONTROL - CATALYTIC CONVERTOR | |||||
| SI-B12-22-08 | 10/01/2009 | 10032574 | Bmw: voluntary emissions recall 08e-a03; m3 s54-dme reprogramming for catalyst conversion diagnosis. the dme programming, as originally installed, may cause the obd diagnostic to erroneously evaluate the efficiency of the catalytic conver | 04/14/2010 | |
| EXTERIOR LIGHTING | |||||
| SIB-63-02-01 | 08/01/2010 | 10037025 | Ready | 04/27/2011 | |
| SIB-63-02-01 | 08/01/2010 | 10037025 | Bmw: procedure for determining and replacing incandescent and halogen light bulbs under warranty. *rm | 04/27/2011 | |
Investigations
| NHTSA ID | Manufacturer | Date open | Date close | Subject | Recall campaign | |
|---|---|---|---|---|---|---|
| EXTERIOR LIGHTING | ||||||
| EA09019 | BMW OF NORTH AMERICA, LLC | 12/18/2009 | 09/28/2011 | Rear Lamp Illumination | 11V438000 | |
| In a letter submitted to the office of defects investigation (odi) dated august25, 2011, bmwindicated that it will conduct a voluntary recall campaign to remedy the subject vehicles.the issue involves the rear lamps in the vehicles body panel.through normal vehicle use over time, the rear lamps ground wiring and associated 8-pin connector can experience an increase of the resistance at the electrical contact points.this can lead to intermittent or permanent loss of the rear lamp functions which include tail, brake, and turn signal operation.the recall consists of modifying the rear lamps in the vehicles body panel by adding a secondary ground connection in parallel to the existing primary ground connection.an 8-pin connector that attaches the primary ground wiring to the rear lamp assembly will also be inspected and replaced if necessary.bmw will complete dealer notification in september 2011 and will begin owner notification in october 2011.all 3 series sedans (except for the m3 sedan which utilized a different rear lamp assembly) that were built between september 1, 2001 and march 1, 2005 are included in this recall, totalling approximately 241,000 vehicles.the action taken by bmw is sufficient to resolve the issues raised by this investigation.accordingly, this investigation is closed. | ||||||
| EA09019 | BAYERISCHE MOTOREN WERKE | 12/18/2009 | REAR LAMP ILLUMINATION | |||
| The outboard rear light assembly consists of a turn signal lamp, a tail lamp and a brake lamp.failure of the light assembly ground circuit results in loss of all three lamps.bmw submitted complaint and warranty information showing a significant number of rear lamp assembly failures due to an open ground connection at the eight pin connector of the light assembly.this results in the loss of the rear turn signal.overheating of the ground circuit electrical pin, possibly due to increased resistance and or high current flow, is indicated in some failures.additionally bmw issued a technical service bulletin (tsb) sib-630306 in february 2007 to address the condition by adding supplementary ground wiring to the tail lamp assembly.the additional ground wire added by the procedure reduces the current flow at the eight pin connector.odi is opening this ea to further investigate the issue. | ||||||
| PE09036 | BAYERISCHE MOTOREN WERKE | 08/07/2009 | 12/22/2009 | REAR LAMP ILLUMINATION | ||
| Odi has received complaints from consumers stating that their tail light assembly is not properly illuminating.the tail light assembly consists of a turn signal lamp, a tail lamp and a brake lamp.the complainants have indicated that the issue is with an 8 pin connector and associated ground wiring.these components are allegedly overheating and melting due to excessive electrical current that runs through the system.bmw issued a technical service bulletin (tsb) sib-630306 on february 2007 to address the condition by adding supplementary ground wiring to the tail lamp assembly.odi is upgrading to an ea to further investigate the issue. | ||||||
| EXTERIOR LIGHTING - BRAKE LIGHTS | ||||||
| EA09019 | BMW OF NORTH AMERICA, LLC | 12/18/2009 | 09/28/2011 | Rear Lamp Illumination | 11V438000 | |
| In a letter submitted to the office of defects investigation (odi) dated august25, 2011, bmwindicated that it will conduct a voluntary recall campaign to remedy the subject vehicles.the issue involves the rear lamps in the vehicles body panel.through normal vehicle use over time, the rear lamps ground wiring and associated 8-pin connector can experience an increase of the resistance at the electrical contact points.this can lead to intermittent or permanent loss of the rear lamp functions which include tail, brake, and turn signal operation.the recall consists of modifying the rear lamps in the vehicles body panel by adding a secondary ground connection in parallel to the existing primary ground connection.an 8-pin connector that attaches the primary ground wiring to the rear lamp assembly will also be inspected and replaced if necessary.bmw will complete dealer notification in september 2011 and will begin owner notification in october 2011.all 3 series sedans (except for the m3 sedan which utilized a different rear lamp assembly) that were built between september 1, 2001 and march 1, 2005 are included in this recall, totalling approximately 241,000 vehicles.the action taken by bmw is sufficient to resolve the issues raised by this investigation.accordingly, this investigation is closed. | ||||||
| EA09019 | BAYERISCHE MOTOREN WERKE | 12/18/2009 | REAR LAMP ILLUMINATION | |||
| The outboard rear light assembly consists of a turn signal lamp, a tail lamp and a brake lamp.failure of the light assembly ground circuit results in loss of all three lamps.bmw submitted complaint and warranty information showing a significant number of rear lamp assembly failures due to an open ground connection at the eight pin connector of the light assembly.this results in the loss of the rear turn signal.overheating of the ground circuit electrical pin, possibly due to increased resistance and or high current flow, is indicated in some failures.additionally bmw issued a technical service bulletin (tsb) sib-630306 in february 2007 to address the condition by adding supplementary ground wiring to the tail lamp assembly.the additional ground wire added by the procedure reduces the current flow at the eight pin connector.odi is opening this ea to further investigate the issue. | ||||||
| PE09036 | BAYERISCHE MOTOREN WERKE | 08/07/2009 | 12/22/2009 | REAR LAMP ILLUMINATION | ||
| Odi has received complaints from consumers stating that their tail light assembly is not properly illuminating.the tail light assembly consists of a turn signal lamp, a tail lamp and a brake lamp.the complainants have indicated that the issue is with an 8 pin connector and associated ground wiring.these components are allegedly overheating and melting due to excessive electrical current that runs through the system.bmw issued a technical service bulletin (tsb) sib-630306 on february 2007 to address the condition by adding supplementary ground wiring to the tail lamp assembly.odi is upgrading to an ea to further investigate the issue. | ||||||
| EXTERIOR LIGHTING - TAIL LIGHTS | ||||||
| EA09019 | BMW OF NORTH AMERICA, LLC | 12/18/2009 | 09/28/2011 | Rear Lamp Illumination | 11V438000 | |
| In a letter submitted to the office of defects investigation (odi) dated august25, 2011, bmwindicated that it will conduct a voluntary recall campaign to remedy the subject vehicles.the issue involves the rear lamps in the vehicles body panel.through normal vehicle use over time, the rear lamps ground wiring and associated 8-pin connector can experience an increase of the resistance at the electrical contact points.this can lead to intermittent or permanent loss of the rear lamp functions which include tail, brake, and turn signal operation.the recall consists of modifying the rear lamps in the vehicles body panel by adding a secondary ground connection in parallel to the existing primary ground connection.an 8-pin connector that attaches the primary ground wiring to the rear lamp assembly will also be inspected and replaced if necessary.bmw will complete dealer notification in september 2011 and will begin owner notification in october 2011.all 3 series sedans (except for the m3 sedan which utilized a different rear lamp assembly) that were built between september 1, 2001 and march 1, 2005 are included in this recall, totalling approximately 241,000 vehicles.the action taken by bmw is sufficient to resolve the issues raised by this investigation.accordingly, this investigation is closed. | ||||||
| PE09036 | BAYERISCHE MOTOREN WERKE | 08/07/2009 | 12/22/2009 | REAR LAMP ILLUMINATION | ||
| Odi has received complaints from consumers stating that their tail light assembly is not properly illuminating.the tail light assembly consists of a turn signal lamp, a tail lamp and a brake lamp.the complainants have indicated that the issue is with an 8 pin connector and associated ground wiring.these components are allegedly overheating and melting due to excessive electrical current that runs through the system.bmw issued a technical service bulletin (tsb) sib-630306 on february 2007 to address the condition by adding supplementary ground wiring to the tail lamp assembly.odi is upgrading to an ea to further investigate the issue. | ||||||
| EA09019 | BAYERISCHE MOTOREN WERKE | 12/18/2009 | REAR LAMP ILLUMINATION | |||
| The outboard rear light assembly consists of a turn signal lamp, a tail lamp and a brake lamp.failure of the light assembly ground circuit results in loss of all three lamps.bmw submitted complaint and warranty information showing a significant number of rear lamp assembly failures due to an open ground connection at the eight pin connector of the light assembly.this results in the loss of the rear turn signal.overheating of the ground circuit electrical pin, possibly due to increased resistance and or high current flow, is indicated in some failures.additionally bmw issued a technical service bulletin (tsb) sib-630306 in february 2007 to address the condition by adding supplementary ground wiring to the tail lamp assembly.the additional ground wire added by the procedure reduces the current flow at the eight pin connector.odi is opening this ea to further investigate the issue. | ||||||
| EXTERIOR LIGHTING - TURN SIGNAL | ||||||
| EA09019 | BMW OF NORTH AMERICA, LLC | 12/18/2009 | 09/28/2011 | Rear Lamp Illumination | 11V438000 | |
| In a letter submitted to the office of defects investigation (odi) dated august25, 2011, bmwindicated that it will conduct a voluntary recall campaign to remedy the subject vehicles.the issue involves the rear lamps in the vehicles body panel.through normal vehicle use over time, the rear lamps ground wiring and associated 8-pin connector can experience an increase of the resistance at the electrical contact points.this can lead to intermittent or permanent loss of the rear lamp functions which include tail, brake, and turn signal operation.the recall consists of modifying the rear lamps in the vehicles body panel by adding a secondary ground connection in parallel to the existing primary ground connection.an 8-pin connector that attaches the primary ground wiring to the rear lamp assembly will also be inspected and replaced if necessary.bmw will complete dealer notification in september 2011 and will begin owner notification in october 2011.all 3 series sedans (except for the m3 sedan which utilized a different rear lamp assembly) that were built between september 1, 2001 and march 1, 2005 are included in this recall, totalling approximately 241,000 vehicles.the action taken by bmw is sufficient to resolve the issues raised by this investigation.accordingly, this investigation is closed. | ||||||
| EA09019 | BAYERISCHE MOTOREN WERKE | 12/18/2009 | REAR LAMP ILLUMINATION | |||
| The outboard rear light assembly consists of a turn signal lamp, a tail lamp and a brake lamp.failure of the light assembly ground circuit results in loss of all three lamps.bmw submitted complaint and warranty information showing a significant number of rear lamp assembly failures due to an open ground connection at the eight pin connector of the light assembly.this results in the loss of the rear turn signal.overheating of the ground circuit electrical pin, possibly due to increased resistance and or high current flow, is indicated in some failures.additionally bmw issued a technical service bulletin (tsb) sib-630306 in february 2007 to address the condition by adding supplementary ground wiring to the tail lamp assembly.the additional ground wire added by the procedure reduces the current flow at the eight pin connector.odi is opening this ea to further investigate the issue. | ||||||
| PE09036 | BAYERISCHE MOTOREN WERKE | 08/07/2009 | 12/22/2009 | REAR LAMP ILLUMINATION | ||
| Odi has received complaints from consumers stating that their tail light assembly is not properly illuminating.the tail light assembly consists of a turn signal lamp, a tail lamp and a brake lamp.the complainants have indicated that the issue is with an 8 pin connector and associated ground wiring.these components are allegedly overheating and melting due to excessive electrical current that runs through the system.bmw issued a technical service bulletin (tsb) sib-630306 on february 2007 to address the condition by adding supplementary ground wiring to the tail lamp assembly.odi is upgrading to an ea to further investigate the issue. | ||||||
Consumer Complaints
| Fail date | miles | occurences | Purchase date |
|---|---|---|---|
| EXTERIOR LIGHTING | |||
| 08/10/2008 | 90127 | ||
| Please let this notice serve as a formal petition for an investigation of a safety-related design defect. the rear tail light bulbs aren't working on the driver's side. the ground wire in the connector, connecting to the bulb carrier seems to be damaged due to a bad ground. i have been replacing bulbs for the last two years. | |||