Bmw F650 Gs 2006
Model F650 Gs made in 2006 by Bmw got 1 recall as well as 10 service bulletins. Technical service bulletines regarding electrical system and engine and engine cooling. There was one recall concerning structure .
Model 2006
Recalls
Campaign | Manufacturer | Manufacturing date | Type | # of units affected | Date Owner notified Mfg | Recall Initiated by | Manufacturers of recalled vehicles/products | Report Recieved Date | Record Creation Date | Regulation Part Number | FMVSS Number | |||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
STRUCTURE - MOTORCYCLE KICKSTAND/CENTER STAND | ||||||||||||||||
07V151000 | BMW OF NORTH AMERICA, LLC | from 06/23/2006 to 08/31/2006 | V (Vehicle) | 305 | 06/01/2007 | MFR | BMW OF NORTH AMERICA, LLC | 04/03/2007 | 04/05/2007 | |||||||
Defect Summary | On certain motorcycles, the weld between the side stand and the frame bottom section was not positioned properly. the load-bearing capability of the side stand is affected. as a result, the side stand could fail. | |||||||||||||||
Consequence Summary | If this occurred when the motorcycle was parked, the motorcycle could fall to the ground and injure a person sitting on the motorcycle or a person nearby. | |||||||||||||||
Corrective Summary | Dealers will install a new frame bottom section free of charge. the recall began on june 1, 2007. owners may contact bmw at 1-800-831-1117. | |||||||||||||||
Notes | Customers may contact the national highway traffic safety administration |
Bulletins
Bulletin | Bulletin date | Replacement Bulletin | Item no. | Summary | Added |
---|---|---|---|---|---|
ELECTRICAL SYSTEM - WIRING | |||||
TB-61-002-08 | 09/01/2008 | 10029188 | Bmw mc: wiring harness of motorcycles is routed along right hand top rail of frame. weld spatter on frame and/or adverse routing in vicinity of banjo bolt of hydraulic spring base adjuster can result in chafing of the wiring harness. m | 06/24/2009 | |
ENGINE AND ENGINE COOLING - COOLING SYSTEM - HOSE | |||||
TSB-17-001-09 | 03/01/2009 | 10029624 | Bmw motorcycle: the coolant inlet hose is not compliant with the applicable bmw specifications. engine operation can cause the inlet hose to widen and become correspondingly shorter; overtime this contraction in length can cause the hose to | 07/13/2009 | |
EXTERIOR LIGHTING | |||||
SIB-63-02-01 | 08/01/2010 | 10037025 | Ready | 04/27/2011 | |
SIB-63-02-01 | 08/01/2010 | 10037025 | Bmw: procedure for determining and replacing incandescent and halogen light bulbs under warranty. *rm | 04/27/2011 | |
FUEL SYSTEM, OTHER | |||||
SB-00-021-07 | 11/01/2007 | 10030825 | Bmw motorcycle: engine fuels containing ethanol. bmw motorrad has no objection to the use of si engine fuels containing up to a maximum of 10% ethanol and imposes no warranty restrictions. ethanol mixtures in proportions higher than 10% | 12/07/2009 | |
FUEL SYSTEM, OTHER - STORAGE - TANK ASSEMBLY - PRESSURE RELIEF DEVICES | |||||
13-003-08 | 06/01/2008 | 10026845 | Bmw motorcycle: replacement of fuel-pressure sensor. check of position of protective film (f-800 gs only). *pe | 12/29/2008 | |
SERVICE BRAKES, AIR - ANTILOCK - WHEEL SPEED SENSOR | |||||
SB-61-003-08 | 10/01/2008 | 10028386 | Bmw vehicles: routing abs front wheel speed sensor cable. the wiring harness front wheel speed sensor periphery plug connection is mounted on the fork cover at the bottom. *pe | 03/27/2009 | |
SERVICE BRAKES, HYDRAULIC - ANTILOCK - WHEEL SPEED SENSOR | |||||
SB-61-003-08 | 10/01/2008 | 10028386 | Bmw vehicles: routing abs front wheel speed sensor cable. the wiring harness front wheel speed sensor periphery plug connection is mounted on the fork cover at the bottom. *pe | 03/27/2009 | |
STEERING - WHEEL AND HANDLE BAR | |||||
13-003-08 | 06/01/2008 | 10026845 | Bmw motorcycle: replacement of fuel-pressure sensor. check of position of protective film (f-800 gs only). *pe | 12/29/2008 | |
VEHICLE SPEED CONTROL - CABLES | |||||
SB-61-003-08 | 10/01/2008 | 10028386 | Bmw vehicles: routing abs front wheel speed sensor cable. the wiring harness front wheel speed sensor periphery plug connection is mounted on the fork cover at the bottom. *pe | 03/27/2009 |