Recalls


CampaignManufacturerManufacturing dateType# of units affectedDate Owner notified MfgRecall Initiated byManufacturers of recalled vehicles/productsReport Recieved DateRecord Creation DateRegulation Part NumberFMVSS Number
SERVICE BRAKES, HYDRAULIC - PEDALS AND LINKAGES
01I006000GENERAL MOTORS CORP.from 03/01/1992 to 07/31/1993I25577007/13/2001ODIGENERAL MOTORS CORP.07/02/200107/19/2001
Defect SummaryThis is not a safety recall in accordance with the safety act. however, it is deemed a safety improvement campaign by the agency. vehicle description: 1992-1994 chevrolet and gmc suburbans equipped with vacuum power-brake assist and ebc4 anti-lock brake (abs) modules. these vehicles exhibit poor brake system performance.
Consequence SummaryThis could be attributed to brake pedal feel.
Corrective SummaryDealers will install a new brake pedal pad. in addition, dealers will inspect the brake-booster output rod and replace it if necessary.
NotesGm has decided to conduct a service campaign to advise owners to have the brake pedal pad replaced on their vehicles.owners can contact chevrolet at 1-800-222-1020 or gmc at 1-800-462-8782, concerning this program.

Bulletins


BulletinBulletin dateReplacement BulletinItem no.SummaryAdded
SERVICE BRAKES, HYDRAULIC
98865020A09/01/199886-50-20602774Vehicles leading or pulling to either side while applying the brakes, and premature front brake wear, especially vehicles that have been used to tow a heavy load. *yc01/13/1999
SERVICE BRAKES, HYDRAULIC - ANTILOCK
0112506/29/2001623419Special policy bulletin regarding product enhancement brake system subjective feel / poor brake system performance. *tt10/29/2001
0100506/01/2001623411This special policy product enhancement covers vehicles equipped with vacuum power brake assist and ebc4 abs brake modules exhibitng poor brake system performance / brake system subjective feel. *tt10/29/2001
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS
990524001A09/01/1999990524001608388Brake lead/pull and front brake wear. *mjs11/26/1999
99052400106/01/1999865020A606765Some cab chassis, crew cab, and pickup models may exhibit a brake lead / pull and front brake wear. *tt09/02/1999
9886502004/01/1998601128Vehicle leading or pulling to either side while applying the brakes or front brake wear not meeting expectations. *yc07/01/1998
SERVICE BRAKES, HYDRAULIC - POWER ASSIST
0100506/29/2001623509Some vehicles equipped with vacuum power brake assist and ebc4 abs brake modules may comment that their vehicles exhibit poor brake system performance, this may be attributed to brake pedal feel. *slc10/29/2001

Investigations


NHTSA IDManufacturerDate openDate closeSubjectRecall campaign
SERVICE BRAKES, HYDRAULIC
EA95026GENERAL MOTORS CORP.09/20/199509/20/2001POOR BRAKE PERFORMANCE01I006000
 Poor performance of abs brakes

Consumer Complaints


Fail datemilesoccurencesPurchase date
SERVICE BRAKES, AIR - ANTILOCK
10/07/2000507/01/1999
 During slow speed stop, brakes were applied with no effect. accident occurred. this has happened on at least 5 occasions, although this is the first resulting in an accident. reported to dealer the first time it happened and i was told it was a driver mistake.
09/03/2000104/01/1997
 The abs system failed to stop the vehicle during a rapid stop. the abs system cycled repeatedly during the rapid stop, but failed to quickly stop the vehicle. as a result, a minor accident occurred when i hit the vehicle in from of me.
01/31/19942006/01/1993
 Anti-lock brakes free wheel when trying to stop going from pavement to slick or washboard road surface. the stopping distance is not reliable. i disconnected the antilock brake system because it wasn't reliable. the dealer could not document the problem because it was intermittent. this is a major defect and nearly caused several accidents before i pulled the abs fuse. chevrolet sent me a video on abs when i reported the problem to them implying that i didn't know how abs worked. i know when abs doesn't work and the car freewheels nearly into the car ahead of you. chevrolet should repair this problem to prevent future catastrophic accidents and injuries.
08/07/1999311/01/1997
 Has failed three times, on panic stops
12/01/1998204/01/1996
 Iwas driving my son to an orthodonic appointment mid morning, good weather conditions. there was red light ahead with two cars stopped. when i braked, my vehicle would not stop, and i hit the car in front of mine, which then hit the vehicle in front of it. it felt like i did not have brakes that functioned properly. it was confusing to me and i guess i blamed it on the pavement. now the same thing has happened to me husband and i now know there is definatly a brake problem. my husband had unplugged the abs system, on the advice of the chevrolet dealership. we're both concerned about our insurance and would like some help if they try to raise our rates. we're also out insurance deductibles, not to mention all the nights i could not sleep thinking about the accident. please feel free to call me if you have any questions. maribel kuehl
06/11/1999204/01/1996
 The abs system on my suburban failed to stop my vehicle in time to avoid a collision with the vehicle in front of me making a right hand turn. i was not speeding and the weather conditions were great. i also had plenty of space between both vehicles. i braked, the abs system took over, and my vehicle would not stop. i simply ran right into the back of the vehicle in front of me. i was aware that something was wrong and complained to the dealership and my insurance company about not being able to stop. i did not occur to me to file a complaint with the govenment until now. i am concerned about my insurance coverage going up or even being cancelled. my wife had the same thing happen to her 12/1/98. exactly the same problem and i will file another complaint on her accident. please send me any documentation i'll need to prove my case. also, when my vehicle was being repaired in june, even the chevy people advised me to unplug the abs system. they all told me that even they had unplugged theirs. that should tell you something right there about their abs system. and i'm out $1000.00 in insurance deductibles too. your help is greatly appreciated. sincerely, scott a. kuehl
04/01/199403/01/1993
 I was traveling at a low rate of speed(30 mph), on dry pavement, and was confronted with a line of vehicles that came to an abrupt stop. i engaged the abs brake systen on my 1993 suburban only to continue forward and contact the vehicle in front of me. this abs brake system, based on my experience, is marginal to poor at best relative to response and pedeal feel. regards, paul j. leeser
06/09/1999108/01/1993
 Abs system engaged when brake pedal was depressed on dry roadway, resulting in no brakes on vehicle and causing collision with vehicle in front of mine.
11/24/199501/01/1994
 The anti-lock brakes failed the first time on a bright sunny dry day , i was unable to bring my suburban to a stop with plenty of distance between me and the vehicle in front of me. i was cited for unassured clear distance since no skid marks or other explanation could be given at the time. we have had several incidents and close calls since the first accident. we have not had the anti-lock system replaced and were unaware that the unit might cause problems until we recently saw the recall which explains perfectly the type of incidents we have had to try to stop the vehicle. we definately want the nhtsa to investigate further to pursue the anti-lock recall on the 1993 suburbans. the transmission failure was just after the warranty period expired. i complained bitterly to gm customer service and all but $350 was covered in the replacement of the original transmission. the failure occurred with the gearshift in the overdrive position. the transmission could not maintain a lock in the overdrive position and would constantly shift back and forth between 3rd and overdrive gear.
06/01/1993
 Brakes applied, abs seemed to start working, then a 'release' seemed to happen that caused vehicle to require much longer stopping distance. they seemed to 'release' and even though standing on the brakes the vehicle took much too long to stop. abs was disconnected 1.5 years ago because of this being very unsafe. dealer had no idea what was wrong and no fix. we felt very unsafe as it was and it happened many times. could not make it happen to show dealer. they seemed unaware of the problem.
01/07/19949911/01/1993
 No summary
 Came up to a intersection apply the abs brake failed and went thourgh intsection no crash no one was injured .
SERVICE BRAKES, HYDRAULIC
08/15/2003120000
 My suburban has developed a peculiar problem that has left even the dealerships completely clueless!!! the engine heats up to about 180 f (still less than the mid point on the guage) after a couple of hours of driving -- this is quite normal. if we stop and turn the engine off, the vehicle will not start! we have to wait a couple of hours while the engine cools off to about 160 f, and it starts up just fine. we only noticed this since we were on a long cross country drive. the problem is entirely predictable, and we had to plan on two hour stops during our trip. we even drove straight to a dealership in raleigh after straight 6 hour drives so that they could see and diagnose the problem -- but they were completely stumped. i would like chevrolet to help diagnose and fix this problem. the abs module failed without any prior warning. one moment the breaks were fine, the next we were flooring the break pedal and the abs light was on. the mechanics had to go through several attempts at replacing the unit ($1200 for the unit itself). this problem sounds exactly like the issue investigated in 1992-1995 suburbans. i am surprised that the recall was limited to the lighter suvs only -- a decision based on cost (most probably). it stands to reason that the problem would be more critical in heavier vehicles.
01/01/1994210/01/1994
 On two instances, the brake pedal went to floor and braking ability was lost for five to ten seconds. other instances the brakes seized up, rendering them useless.
06/05/1996
 Vehicle is loosing brake fluid. at 31 thousand miles the vehicle has no wear on the front brakes.*ak
SERVICE BRAKES, HYDRAULIC - ANTILOCK
08/01/20068200030
 During all kinds of weather conditions the abs braking system has failed to stop the vehicle, twice causing a rear end accident. during a hard braking situation when on dry pavement, or any braking condition on wet pavement the brakes have been applied and they grab and then release causing the vehicle to continue moving forward without completely stopping. the vehicle has been taken to many chevrolet dealerships and independent shops for repair and been inspected or repaired with complete brake rebuilds with absolutely no improvement in stopping abilities. this model vehicle should absolutely have been recalled shortly after manufacture. there is so much documentation that these vehicles have this problem that this agency should be ashamed of not forcing a recall for repairs or complete redesign of the braking systems. the minor recall andfix of the brake-booster output rod were a joke and never should have been allowed as a fix. the excuse chevrolet uses that it is a brake pedal feel that is the problem is inexcusable and irresponsible. i have been a professional truck driver (class a cdl with all endorsements) and mechanic and have driven several other makes of large heavy passenger trucks and suv's with abs braking and never encountered this problem with any type of vehicle. *tr
04/23/2004152825109/06/1993
 When making a turn at high speeds steering wheel/brakes locked up temporarily. dealership was notified, but did not resolve the problem. *ak *nm
01/02/20035007/10/1993
 Abs fails on uneven surfaces, such as washboard roads and when hitting bumps during braking. abs perform poorly in most conditions, including dry pavement. they do provide some benefit on snow/ice. however, my abs has now failed and overall braking performance is better. this system, and the logic in the controller, need significant changes. *jb
144001
 When consumer attempted to slam on the brakes, the abs activated which caused the vehicle to lunge foward and hit the rear end of another motorist.ts *jb
03/26/19983005/01/1993
 The same proble that is on your recal list prolong bracking distance. *ak
08/01/1999
 No summary listed for above vehicle. *ak
07/01/19983
 When applying brakes pedal feels soft and spongy. brakes failed 3 times, no accident. vehicle taken to dealer twice for this problem, found no problem the first time. second time, master cylinder was replaced. six months after last repairw were done, brakes were fine, then brake failed again.*ak
10/01/1999
 No summary listed for abov e vehicle. *ak
 When applying brakes to come to a complete stop pedal went to floorboard, causing extended stopping distance, resulting in a rear end collision. please give any further details.*ak
05/01/1995
 Abs system can be triggered by any small bump in road. *ak *slc
03/13/2001105/01/1999
 While driving between 35-40 mph consumer applied brakes, first they grabbed, then released. no braking action, and consumer hit vehicle in front, damage was $7000.*ak
6
 While making a sudden stop by depressing brakes abs system did not kick in, causing vehicle to run off road.*ak consumer states this has happened on six other occassions since 1994. *jb
01/01/2001
 Abs system has failed on several occasions at various speeds. open ivestigation ea95026. *ak
01/01/2001
 Consumer had a new abs system installed. then, before getting on highway state trooper stopped consumer, and informed them that they need to put chains on tires due to snow. soon after, when trying to slow down while going down a hill abs went out. dealer was contacted, they noted that abs won't work with chains on tires. *ak
3
 One three occasions when brakes were applied pedal went to floor, causing extended stopping distance, and resulting in a collision. dealer has inspected vehicle, and could not duplicate or correct problem.*ak consumer states master cylinder was checked by two different mechanics and could not find anything wrong, on the advice of conumer's mechanic, the master cylinder was replaced and there has been no further problems. *jb
01/01/1993
 Abs system kicks in without warning or need.*ak
12/07/2000
 While traveling 40-45 mph had to brake suddenly and brakes made an electrical vibrating high pitched noise. several occurrences happened during wet or snowy weather. did not take vehicle to dealer because brakes worked fine most of the time. *ak
06/05/2000
 Ea 95 026/poor brake performance: whenever vehicle runs over a bump/pothole while applying brakes, it causes extended stopping distance. also, has to apply brakes extra hard to get vehicle to stop. manufacturer notified. please feel free to provide any further details on this matter. *ak
11/12/1997506/01/1997
 Windshield wipers constantly shut off when it starts raining, the only way to get them to work is to stop the car and get out and manually force them to work again. they will work for a little while then do it again. the grill : the crome is pealing off of the grill. the brakes; there is intermittent problems. one is the disc keep warping after they have been repaired. they sometime fail to stpo the car as they should. the pedal goes to the floor while trying to stop.*ak
10/01/1997100
 These brakes will not stop the vehicle and the abs caused my wife to slide into anothere vehicle in the rain in stop & go traffic.*ak
08/22/19972006/01/1993
 This is my second submission of a complaint. the first one was odi id 522933. i resubmit because i am intensly frustrated with the apparent lack of action on the part of gm regarding my year vehicle. on 7/21/99, a large gmc recall was announced pertaining to abs problems. my year suburban was excluded pending further investigation. gm stated they were working to address customer satisfaction issues with my year vehicle. they have done nothing with me along these lines. my vehicle continues to experience many of the same symptoms that are described in your current complaint submissions for 1993 suburbans. what is being done?? this is a very serious situation. is gm just waiting until the 92 thru 94s just rot away and are no longer a problem. my vehicle is in excellent shape for 187,000 and i intended to drive it for several more years but the anxiety is getting the best of me. who else can i write or call? this is serious. please contact me on my day number - 512 868 0374. *ak
09/12/2000
 Consumer was traveling about 25mph on highway and she was approaching a intersection, went to apply the brakes, and brakes didn't respond. vehicle didn't stop at all. abs braking system didn't kick in for three minutes, and the braking system didn't respond with a low speed. *ak
 While traveling on rough roads and when depressing brakes there was extended stopping distance . dealer has been contacted. please provide further information.*ak
111/01/1993
 Abs braking system failed many times, one incident resulting in accident. nlm
01/01/2000
 Very poor, unsafe, brake performance, dangerously long stopping distance
07/01/2000112/01/1992
 Whne brakes were applied pedal went to the floor, resulting in extended stoppingdistance. dealer has inspected vehicle and was able to duplicate problem. *ak
08/18/2000112/23/1993
 Consumer's son was traveling about 30mph. while approaching a traffic light applied brakes, and brake pedal went to the floor. vehicle accelerated into another vehicle. there were no injuries. consumer took vehicle to dealership, and mechanic told him that problem couldn't be duplicated. abs brake system wasn't operable. *ak
03/01/20001
 While driving at a approximately 30 mph and brakes are hit, vehicle starts to violently shift to the left. brakes/calipers, and anti-lock brake valves have been replaced. also, rotors were turned by dealership at consumer's expense. manufacturer has a shop bulletin issue to dealership for remedy of problem, but problem still occurs. there has not been a recalle issued. this defect does not allow consumer to stop appropriately, and can cause a serious accident. *ak brake hoses failed. brake fluid was out again after replacing it. *yh
05/05/1996305/01/1996
 Whenever braking on dry pavement abs would kick in without warning. vehicle would fail to stop, resulting in extended stopping distance. took to dealer & had the master cylinder replaced for the third time after it was blown twice in one month. had everything in the brake system was checked, fluids replaced, rotors turned, etc. dealer is unable to identify problem. *ak *ml
1
 Have severe left or right brake pull and erratic operation. *ak
01/01/1997
 No summary listed for above vehicle. *ak
06/11/2000006/01/1993
 When applying brakes pedal goes all the way to the floor. brakes do not grab at all, and vehicle keeps rolling. *ak
 Ea95026; abs braking system malfunctioned, causing extended stopping distance which could cause a crash. dealer could not determine the cause of the problem. ongoing problem since bought brand new vehicle. please provide further information.*ak
 When depressing the brakes wheels locked up. dealer has been contacted and repairs performed, but problem has returned. also had to replaced brake shoes on the rear axle because the right rear brake shoe was burnt from over heating. *ak *ml
01/15/1994
 Extended stopping distance when brakes were applied on wet roads. dealer notified, and informed consumer that vehicle was not covered under manufacturer's recall due to vin. *ak
03/27/20000
 While attempting to stop by applying the brakes vehicle slid, and consumer rear ended vehicle in front of her. no serious accident yet. *ak
 Intermittently when brakes are applied pedal goes to the floor, resulting in extended stopping distance. dealer has been notified.*ak
03/02/2000106/01/1993
 Over the entire time that we have owned this vehicle, the brakes and the abs system have not operated reliably. whenever the vehicle is being driven on an irregular or wet street (even at low speeds, below 30mph), and the brakes are applied, the brake pedal will go to the floor and all braking effect vanishes momentarily. this definately involves the abs system, because there is the characteristic vibration of the pedal when the system is activated. abs activation during these episodes is inappropriate, ineffective, and dangerous to the occupants of the vehicle. *ak
03/02/20001506/01/1993
 Over the entire time that we have owned this vehicle, the brakes and the abs system have not operated reliably. whenever the vehicle is being driven on an irregular or wet street (even at low speeds, below 30mph), and the brakes are applied, the brake pedal will go to the floor and all braking effect vanishes momentarily. this definitely involves the abs system, because there is the characteristic vibration of the pedal when the system is activated. abs activation during these episodes is inappropriate, ineffective, and dangerous to the occupants of the vehicle. *ak
02/10/2000
 When the brakes were applied hard the pedal was normal. however, vehicle experienced extended stopping distance which resulted in a collision. *ak
02/10/2000006/01/1993
 When stepping on the brakes to stop or reduce speed, brake pedal will go to the floor, resulting in extended stoping distance. *ak
 While driving on highway, approaching an intersection, there was an accident up ahead. went to apply brakes, and the vehicle just kept on going. rear ended another vehicle. contacted dealer. *ak
04/15/1997
 Reporting ongoing problem with brake system; whever brakes are applied pedal would intermittently go to the floor and a make a dull sound, and cause a extended stopping distance. dealer notified. *ak
 When applying the brakes the back wheel hits a small bump, pedal goes to the floor, and vehicle does not stop. dealer has not seen vehicle. *ak
03/20/199804/29/1997
 When driving at any speed and applying the brakes, sometimes the brakes go straight to the floorboard, and pull rightor left. sometimes the brakes work intermittently. *ak
08/15/1999
 Abs braking system malfunctioned, causing extended stopping distance which may result in a crash. dealer cannot determine the cause of the problem. please provide further information. *ak
11/05/1997
 While driving 30mph applied brakes and vehicle didn't stop. when on wet surface vehicle makes noises and slides when trying to stop. *ak
10/20/1999
 While making a normal stop brake pedal went down much further than normal and the truck barely stopped. this happened while driving on a smooth/dry road surface. the problem was reported to the dealership. prolbem was corrected by a repair shop at owner's expense. please provide any further information. *ak
09/27/1999
 Ongoing problem with low growling sound and extended stopping distance. can nhtsa help in this matter. *ak
04/21/1993104/21/1993
 The front wheels of anti lock system lock-up causing vehicle to slide on snow / ice. *yc
1006/01/1993
 Repeated failures, particularly with bumps or emergency braking: pedal to floor, brakes groan extended stopping distance with one accident.
 Whenever applying the abs brakes hard vehicle would slide. this caused extended stopping distance. had rearended another vehicle in front. been to dealer & mechanic had test driven vehicle for brakes. the cause of brake problem could not be corrected. *ak
01/01/199640
 When driving at any speed on dry pavement abs brakes will apply, release and reapply. vehicle will roll forwards, and the brakes release again. *ak when brakes are applied in rough road causing, suspension to bounce and anti lock to loss braking action. *yh
12/12/1994105/12/1993
 Vehicle experienced anti-lock brake failure, causing loss of control, resulting in collision. *yc
07/17/1997
 When brakes were applied under normal conditions pedal became soft and went to the floor, causing and extended stopping distance, and resulting in a minor collision. dealer replaced various parts of the brake system. *ak
11/01/1992
 Abs brake failure just before final braking. rear end of car in front. brakes just quit. brake were just serviced on the week before. same aparent problem as recall no 99041 for 93 blazers.
07/13/19991008/01/1993
 While driving 15-20 mph over a speed bump, brakes failed, brakes continually experiencing failure. . *yc
07/12/1999
 Whenever the brakes are applied pedal goes to floor. would pump pedal & abs brakes would reengage to stop vehicle. would experience a greater stopping distance than usual when this happens. had been to mechanic & was informed abs brakes needed new monitor. *ak
03/01/19994
 While making a sudden stop vehicle continued to travel, resulting in extended stopping distance. please prove further information. *ak
12/18/1995
 When abs brakes are applied vehicle would pull to left & swerve. been to dealer numerous times & promised problem would be repaired. but it reappeared. *ak
08/21/1999107/01/1998
 This failure is similar to my previous posting of 2 failures. i was driving at a speed of 30 mph when i had to stop suddenly. the brakes made a loud groaning sound and the wheels locked up in a skid. once again, this almost resulted in a crash. afterwards, the brakes seemed to be very soft for a period of time.
07/19/19992
 Anti-lock brake system failed twice. *yc
03/15/1999207/01/1998
 On first failure, brakes went to the floor when applied at speed of 25 mph. vehicle did not stop as it should have and almost resulted in a crash. on second failure, application of brakes at 30 mph resulted in tire lock and skid. abs was not functioning properly. attempt to recreate the failure mode was unsuccessfull. failures appear to be random.
08/17/19991
 When the brakes were applied in a panic stop , the driver heard a loud noise, pedal became soft and went to the floor, causing extended stopping distance which resulted in loss of master cylinder. the dealer has replaced the master cylinder. *ak *ml
09/01/1992
 Anti-lock breaks provide no/inadequate stopping capability on slightly slippery surfaces. on such surfaces, the abs pump can be heard when holding the break pedal firmly but there is virtually no stopping cabability. i have had to drive off the road or miss turns on numerous occassions due to inadequate breaking. i was disturbed to find this was not part of the recent recall of 3.5 million other gm light trucks as the symptoms described are exactly what i have encountered on my '93 2wd suburban. please help as i feel in jeopardy driving this vehicle in wet and snowy conditions.
05/25/1999503/01/1998
 Anti-lock brake system failed when tires encountered uneven pavement.
 When brakes are applied pedal gets hard, resulting in extended stopping distance, and causing a minor collision. the dealer was not notified. *ak
05/12/1999
 While driving at any speed and applying the brakes, abs will fail. this has caused vehicle to crash twice. *ak
10/26/1994707/01/1993
 Abs brakes engage when braking on uneven dry paved roads under conditions when abs is not needed to stop truck. this causes extremely long stopping distances which has caused one three car collision and one very close miss. dealer said abs system works fine even after accident.
10/01/1996
 Applied brakes at 10mph on wet surface and brakes made loud noise, no brake pressure.consumer contacted dealer. *ak
 Intermittently when the brakes are applied on wet pavements, the abs system activates and the pedal becomes hard, resulting in extended stopping distance. dealer and manufacturer have been notified. *ak
01/01/1995
 When driving at any speed and applying the brakes, the abs system kicks in, and the abs brakes are work intermittently. *ak
05/22/1999306/01/1997
 Travelling at 25 mph, applied brakes and the antilock system came on. they did not stop the vehicle even though there was plenty of room to stop. brakes made a loud motor running type noise and failed to stop the vehicle.
07/09/199911/10/1992
 Abs is not working, causing extended stopping distance. dealer claims needs ehcu unit to correct problem. *ak *ml
 When the brakes are applied vehcle pulls to the right. the dealer has been notified. *ak
 While making an emergency stop vehicle experienced extended stopping distance which resulted in a rearend accident. *ak
2
 Abs system caused near accident due to extended stopping distance - both occured at low speeds approaching intersections on dry highway surfaces (may have encountered small amount of sand/gravel on one wheel) abs activated causing vehicle to enter the intersection, narrowly avoiding collision. *ak
08/11/1997306/01/1993
 Master cylinder replaced three times and currently having same problem. *ak
12/01/1992
 I am sending this in regards to recall that was just publicized on gm's, but not suburban. my truck is exceedingly hard to stop it pulls left and right and takes longer to slow down. repair cost $1200.00. windshield wipers & washers won't work. cost $350.00. *ak
07/13/19991
 Hit brakes in traffic going 25 mph and the vehicle felt as if it lunged forward before the antilock feature enabled not in time to avoid hitting the car in front of me. i feel the antilock brake feature did not work correctly! *ak
06/30/19941007/01/1993
 This has occurred since the truck was new. it appears as if the abs is failing on rough grades. it has happened mostly when coming to a stop at intersections. the dealers (3) have all not been able to reproduce the problem. when it happens, the pedal will go to the floor and the abs makes a grinding noise. you have to pump the pedal 2 or 3 times to restore the brakes. this does not happen every time the vehicle stops. i feel sure that this will result in a recall now that your agency is involved. thank you and have a nice day.*ak
04/01/1999
 #ea95026 consumer was driving at approximately 52 mph , consumer had to make a sudden stop, and within 90 feet span vehicle only deaccelerated to 45 mph even with the brakes fully applied, causing a rear end collision. cosnumer heard the abs kick in, but the vehicle would not slow down. *ak
09/01/1993108/01/1993
 If surface is rough when braking we often get a surge forward when the anti-locks kick in. such as when the tires bounce slightly while braking. this has caused us to go into an intersection while trying to stop and it extends the stopping distance. we have had this problem since time of purchase but are told by chevy that there is no recall thus no corrective action available. *mjs
05/14/1993
 There is a delayed action in the abs system. the pedal goes partially to the floor. vehicle goes in a free wheel before abs brakes engage. this has happene deven on dry ground if the vehicle hits any defect in the road, causing the wheel to skip and activating the abs system. vehicle was involved in a collision due to abs failure.
07/01/199303/01/1993
 The problem with the abs brakes is ongoing, there is no fix. when going down a slight incline on the road, and if the road has some slite ribbing or wash board effect, the brakes fail completely if used in a panic stop situation, even if one continues to push the brake pedal as instructed with abs. also medium ie 50 mph panic stops also have the same effect. the problem seems to be a long hesatation before the abs starts its cycle of braking, and any road irregularities or road sand increases this hesitation before the abs starts its braking cycle. it should be noted that the master cylinder was changed early in 1993 to no avail. it would appear to be a software problem in the abs logic controller. *ak
03/13/1999
 In emergency stop braking system malfunctioned. there was no braking ability at all, and the vehicle just coasted along, resulting in a crash. *ak
08/01/19972
 Abs brakes failed twice, once resulting in an accident.
 When applying the brakes the abs kick in and the vehicle does not stop. dealer couldnt find problem. *ak
01/25/19991006/01/1998
 Brakes lock up on rough or slippery surfaces/grinding noise after abs kicks in/loss of control when braking quick/dealer service center says no problem everything is o.k. *ak
11/01/1997
 Abs brakes; on two occasions when applying the brakes in wet weather, the brakes failed, causing the vehicle to go into a skid. *ak
10/10/1997208/25/1997
 While driving applied the brakes and the pedal went to the floor, and the vehicle would not stop. *ak
06/06/1997
 When making a sudden stop on slick road surfaces the wheels locked up, causing the vehicle to slide into another. the dealer has not been notified. *ak
10/01/19972
 Ea94-038; intermittently the defective abs braking system malfunctioned, causing brake pedal to fade and extended stopping distance which almost resulted in an accident. *ak
3
 When applying the abs brakes on normal road conditions the pedal will travel to the floor, causing extended stopping distance which could result in a collision. *ak
112/01/1993
 Anti lock brakes have failed several times one incident caused vehicle accident.
301/01/1993
 Anti lock brakes continually failing, replacement of the front wheel brakes did not rectify abs failures.
1
 Anti lock brakes fade causing extended stopping distances.
09/18/1998406/01/1993
 Was driving 40mph & started to apply the brakes, traveled 40 ft & hit 4 vehicles due to brake failure. heard abs computer come on. brake pedal got mushy. *ak
10/13/19983
 Had applied brakes at 30mph vehicle did not stop right away. brake pedal was soft & went to floor. vehicle towed to dealer. entire abs brake system had failed & needs to be replaced.
1
 Anti lock brakes fail to stop vehicle causing vehicle to slide.
05/01/1995
 Master cylinder has been replace and brake problems persists. please forward any information regarding these brake problems.
08/07/1998
 When brakes were applied in a panic stop the pedal went to the floor, resulting in extended stopping distance, causing a collision. the dealer has been notified. *ak
 Abs brakes; when applying brakes in normal conditions, the brakes failed to stop the vehicle, causing extended stopping distance before vehicle came to a complete stop. please provide details. *ak
07/05/1997
 Abs brakes; when applying brakes in a panic stop, the pedal went to the floor and brakes failed to stop the vehicle, causing an accident. vehicle rolled over. please provide details. *ak
05/01/1998208/01/1996
 Ea95-02o; consumer states when driving at any speed occassionally, upon depressing the brake pedal to make a normal stop. the abs brakes kick in, causing no response to the wheel, resulting in extended stopping distance which caused an accident a accident on two different occasions. consumer has contacted the dealer.*ak also brakes pads were worn out and making noises, cassette player was inoperable.*jb
08/01/1994308/01/1994
 Ea95-026; when traveling at any speed and attempting to make a sudden or gradual stop, the pedal travels to the floorboard, causing an extended stopping distance, resulting in the consumer going through an intersection and causing an accident. consumer has contacted the dealer, dealer has replaced parts, problem still occurs. *ak consumer called to update accident report 04-01-99 applied abs brakes at 35 mph and the pedal went to the floor causing extended stopping distance to occur which resulted in a collision, abs system malfunction caused the accident. *mjs
07/10/1998203/01/1993
 Consumer's daughter started to apply brakes to stop, and the brakes did not catch. driver hit vehicle in front of her, causing minor damage to the other automobile. *ak consumer has contacted the dealer several times who states that there is nothing wrong with the brakes, however the service staff has warned the consumer to be careful because the brakes fail periodically, consumer usually experiences failure between 20-25 mph, when re-applying the brakes, the vehicle usually stops with wheels locking and skidding. *slc
05/17/1998401/01/1993
 Anti lock brakes failed resulting in a vehicle collision.
06/18/19983
 When driving vehicle and using brakes in a panic stop ,the braks would fail to operate. this condition has occurred on several occasions. vehicle has been in/out dealer shop. dealer always informed the consumer that nothing could be found. *ak
06/10/1998
 While driving consumer tried to make a stop. pressed the brake pedal to the floorboard, vehicle continued to travel. consumer continued to press the pedal and the vehicle stopped. *ak
04/15/19980
 When applying brakes there is a period when the brakes do not catch. consumer has not had an accident yet, but is afraid of brake performance. *ak
02/21/1997
 When trying to make a panic stop and mashing the brake pedal down the truck continues to roll forward and then t stops. it takes a few seconds the anti-lock brakes will start to activate and vehicle starts to roll. *ak
3
 When brakes are applied in a panic stop the master cylinder blew out, resufied. *ak
5
 When applying the abs brakes the pedal will trvael to the floor, causing extended stopping distance. please give any further details. *ak
12/18/19955
 Whenever abs brakes are applied, the abs would lock up. happens during rainy weather. its an intermittent problem. this causes the vehicle to have a much longer stopping distance. *ak
06/10/1997
 While driving applied the brakes and the abs brakes kick in , but there are no rear brakes on the truck. owner noticed that the abs lights are always on. *ak
2011/07/1997
 Abs brakes fails intermittently.
11/14/1997204/01/1993
 Anti lock brakes failed/locked up, resulting in two vehicle collisions.
04/13/1993
 Abs brakes; when applying brakes in normal conditions and in panic stops, there is an extended stopping distance before vehicle comes to a stop. *ak
 When braking moderate to severe pressure, abs will begin to pulsate and result in a loss of brakes for about 15-20 feet. cannot control vehicle, dealer has inspected and road tested vehicle, but cannot determine problem. *ak
302/06/1993
 Brakes failed.
12/01/1997201/01/1993
 Abs goes all the way to floor
11/01/1997509/01/1993
 Abs brakes; when applying the brakes in a panic stop, the pedal goes to the floor and the vehicle continues to move forward. dealer unable to remedy the problem. *ak
02/01/1998609/01/1995
 Abs brakes; when applying brakes in normal conditions, the pedal goes to floor and brakes failed to stop vehicle, resulting in extended stopping distance. *ak
109/01/1993
 Anti-lock brakes failed to stop effectively resulting in a collision.
103/29/1993
 Anti-lock brakes lock up in the front and do not hold in the rear, causing loss of brake control.
108/15/1997
 Hard brake application results in extended stopping distance.
09/05/1994110/12/1993
 Anti-lock brakes failed, resulting in accident.
109/01/1996
 Anti-lock brakes do not stop efficiently in snow or ice.
01/21/1998202/19/1993
 Anti lock brakes not working properly, experiencing extended stopping distance.
12/03/19972
 Anti lock brakes failed resulting in a vehicle collision, repairs made prior to incident however no improvement.
 When applying the brakes the vehicle pull's to the left. dealers has service problem. please provide further details. *ak
07/01/1997301/01/1993
 When the brakes are applied the pedal goes down further than usual, resulting in extended stopping distance. *ak
08/15/19973
 Whenever brakes are applied, it would be ery hard to brake, especially over 30mph. this would cause the vehicle to have a longer stopping distance.
05/10/1997112/01/1994
 Anti lock brakes failed, causing acciednt.
101/01/1995
 Anti lock brakes lock up under slippery conditions.
108/14/1993
 Brake pedal goes to the floor.
202/01/1997
 Brakes failed.
07/01/1997103/20/1995
 Anti lock brakes fail continuously.
10/10/199708/01/1993
 When brakes were applied, a spring sound was heard and the vehicle released and continued going, causing extended extended stopping distance, resulting in a collision. the dealer has been notified. *ak
11/01/199611/01/1996
 When the brakes are applied the pedal goes to the floor and, the vehicle pulls to the left, resulting in extended stopping distance. the dealer has been notified. *ak
101/14/1993
 Abs works poorly, failed to stop in reverse, causing small trailer to jackknife, resulting in damage to truck.
807/21/1993
 Brakes do not work properly, driver almost rear ended vehicle.
207/01/1995
 Anti lock brakes failed.
05/01/1997805/01/1997
 Anti-lock brake system has failed on several occasions.
110/01/1993
 Abs brake system fails to stop the vehicle properly, extended stopping distance when applying brakes.
803/01/1994
 Brake failure on several occasions, not able to determine cause.
07/01/1995107/01/1995
 Anti lock brakes failed.
11/01/1997101/01/1995
 Brakes locked up.
807/01/1993
 Abs brakes failed several times.
04/01/1994412/07/1993
 Anti-lock brakes failed.
 When appyling the abs brakes on wet or dry pavement the pedal will travel to the floor, causing extended stopping distance. dealer cannot idenitfy the problem. please give any further details. *ak
04/24/1996
 Abs failure. totally failed to stop vehicle several times, pulls hard to the right, and brake pad wore out in one month and destroyed the rotor.
04/24/1996
 Multiple abs failures.
09/05/199601/01/1993
 The brakes do not respond properly under hard braking situations. the anti-lock brakes pulse loudly but do not allow brakes to engage.
01/07/19939
 Ea95-026; consumer experiencing excessive wear of the front brake pads and rotors. also, upon making a sudden stop, consumer noticed extended stopping distance/ brake fade away. consumer has contacted the dealer. *ak
08/31/1997205/06/1997
 Brake problems.
10/30/199709/03/1997
 Depressed pedal no sensorizaton, traveled completely to floor, returned to resume postion after pedal reapplication. *ak
01/01/1993
 When applying the brakes the vehicle takes too long to slow down. dealer says that it is the way they're suppose to be because of the weight and size of vehicle. *ak
06/19/1993
 Cannot stop vehicle in panic situation; vehicle glides to a stop. also, when braking on rough pavement, pedal goes to floor and abs kicks in in preventing quick stop. *ak
05/01/1997212/09/1992
 Anti-lock brakes locked up/failed twice, causing vehicle to pull to the left. *ak
10/15/19975
 During emergency stops the brakes do not engage. the abs system has to be pumped to stop the vehicle. when the brakes are applied ther is a squeaking noise. the dealer has been notified. *ak
 When the brakes are applied the vehicle shimmies, resulting in extended stopping distances. the dealer has repaired the vehicle, but the problem still exists. *ak
 While driving the vehicle consumer tried to make a sudden stop by depressing the brake pedal, the vehicle continued to travel. consumer depressed the pedal again, the vehicle stopped. *ak
 Abs do not stop in sufficient time. sometimes in sudden stop they will not brake, about 2 car lengths before coming to a complete stop. dealer said consumer was not used to having a big vehicle. *ak
 Abs; in an emergency stop hears noises, pedal goes to floor , no brakes.takes about 3 car lengths before it comes to a complete stop. dealer replaced all brake system. cannot find problem. *ak
02/10/1996
 While driving applied the brakes and the pedal went to the floor, causing the truck to be involved in a collision. *ak consumer states that on 4/20/98 when brakes were applied the pedal went to the floor resulting in extended stopping distances causing a collosion injuring the driver of the other car. the dealer has been notofied.
 Owner has abs brakes. while driving vehicle on wet pavement vehicle will not stop when brakes are applied. dealer cannot find a problem. *ak
07/01/199305/01/1993
 Ea95-026, the braking system malfunctions when there is a sudden stop, having extended stopping distance,causing rearend accidents on dry payment. dealer cannot determine problem. *ak
08/22/1997
 Whenever brakes (abs) are applied, the pedal goes down to floor; happens intermittently. stopping distance would be extended. because of this problem, vehicle ended up ina ditch & was totaled. *ak
 Abs brakes; when applying the brakes in normal conditions on a wet surface or on a rough pavement, there is an extended stopping distance. please provide further details. *ak
 When brakes are applied the pedal goes to the floor , resulting in extended stopping distance. the dealer has been notified. *ak
10/31/19975
 When applying abs brakes, pedal goes to the floor; it's intermittent failure that causes extended stopping distance. on occasions, brakes would make a grinding sound while trying to make turns or applying brakes (abs). *ak
10/27/1997606/01/1993
 Consumer states that in an emergency stop, the pedal goes to the floor, resulting in extended stopping distance. the dealer has been notified. they replaced the ecm on the vehicle. *ak *slc
 When applying the brakes make a noise and vibrate. there is also less braking ability. it mostly happens at low speeds. *ak
10/24/1997
 During panic stops the brakes grab and let go, resulting in extended stopping distance, causing the vehicle to collide. the dealer has been notified. *ak
07/01/19972
 Ea95026, the defective abs braking system malfunctioned, causing the pedal to touch the floor, noises and extended stopping distance which may cause an accident. dealer replaced brake master cylinder 2 times. dealer cannot determine problem. *ak
 Abs brakes; when applying the brakes under normal conditions, the pedal goes to the floor and the brakes fail to stop the vehicle. replaced brake pads. *ak
12/16/1996
 When driving the truck and applying foot to the brake pedal the truck does not stop right away, it takes longer to stop. *ak
6
 While driving, tried to stop vehicle, but did not stop. consumer feels unsafe about the brakes. her husband had checked the vehicle in his shop. *ak *slc
07/01/1997203/01/1996
 While driving at approximately 30 mph when wanting to make quick stop, abs do not stop right away,no pattern. sometimes abs light comes on, usually when starting vehicle. this defect can result in an accident. *ak *slc
7
 While driving vehicle applied brakes, but vehicle did not stop and did act like a free road, according to consumer. the vehicle was taken to dealer, and they said:is no problem with the vehicle's brakes. the consumer asked dealer if they could diconnect the abs because he did not feel secure. *ak
08/06/1997306/01/1995
 Ea95-026; consumer was traveling about 30 to 35 mph applied force to the brake pedal to make a sudden stop to avoid hitting a dog, pedal traveled to the floorboard, vehicle continued to move. *ak consumer states this failure has happened on 3 occasions, at different speeds. *slc
02/01/1993
 The defective abs system malfunctioned, causing extended stopping distance, and causing the vehicle wheels to lock up and slide. dealer cannot determine problem. *ak
10/15/199710
 When braking on downhill slope and/or hitting bump, driver will temporary lose braking power; pedal sometimes soft/goes to floor; mostly low speed; wet/dry surface. brake system not checked by dealer/mechanic. *ak
10/10/1997
 Upon making a gradualor a sudden stop consumer noticed a loud sound, rear brakes locked up. pulstation in the brake pedal, resulting in extended stopping distance. *ak
04/15/19972
 Brakes failed to stop vehicle during panic braking, driver slammed on brakes, pedal went to floor, vehicle went through stop sign, no warning, released brakes, applied again, brakes worked okay, dry weather, brakes not checked by dealer/jmechanic. *ak this has also happened again. *yd
06/06/1995
 Abs brake problems; when hitting a bump and applying the brakes at the same time lose brakes. the pedal goes down a considerable distance, and have no brakes what so ever. has to take foot off the brake and reapply. the problem has been reported to the dealership. problem still exists. *ak
06/10/19971
 When applying the brakes the vehicle keeps going and the pedal goes to the floor.*ak the driver has to pump the brakes to get the vehicle to stop. *nlm
06/06/19934
 Abs brake problems; intermittently; while driving on regular road conditions, during normal braking when applying the brakes, the pedal almost reaches the floorbroad and system will kick in and stop. the vehicle surges forward before it stops. the front brakes pads have been replaced (4) times in 70,000 miles. both calipers have been replaced, and the rotors on the right side. consumer is still experiencing a braking problem. *ak
12/18/19963
 Was driving vehicle when the abs failed to work. this caused the vehicle to have extended stopping distance which caused an accident. *ak
10/15/19933
 Abs: applied brakes, could hear abs kick in, brakes released, did not grab, pedal went to floor, vehicle went through intersection, rearended another moving vehicle, problem has caused three crashes, dry weather with water puddles; according to dealer, brakes are working fine. owner does not understand abs. *ak
10/10/1996
 Abs brake problems; intermittently, on any type of road conditions, when applying the brakes the vehicle goes to the left or to the right. the calipers were replaced about a month ago, problem still exists. at high speed, when pressing the pedal there is no brake, and vehicle cannot come to a stop. *ak
05/28/1995
 After engagement of abs sensor mode functioned momentarily and suddenly released. result: vehicle crashed 2 times. *ak
 While drivng vehicle on wet pavement the abs brakes will lock up and then release. owner is very concerned for safety. owner has not taken vehicle to dealer. *ak
07/27/1997
 During brake application abs stutters/catches and stops. sporadic grab release motions. probable cause: collision. *ak
09/03/1997305/01/1993
 Going 30mph when brake light came on. the hydraulic booster did not work; had to press on brakes hard to stop vehicle. took to dealer & had computer replaced. *ak left front seat belt would not retract at times. *slc
02/01/199702/16/1997
 Intermittent abs brake failure. *ak
06/01/1996
 The abs brakes fail quite often. dealer and local mechanic claim that nothing is wrong with vehicle. *ak
06/10/19972
 Applied the brakes and the vehicle would not stop. the driver had to switch lanes to avoid hitting another vehicle. the brakes went out two different times. *ak *slc
10/10/1997100
 While driving at any variuos speed, goes to apply brake vehicle pulls to left. has to pull to right in order to gain control. front end of vehicle vibrates, mechanic replaced front capliers/,rotated tires/cleaned and adjusted rear brakes. this defect can cause a serious accident. *ak
05/01/19972
 While driving about 30 mph went to stop at an interection, applied brakes ,went to floor, did not regain brakes, changed gear to nuetral then to park in order to stop.dealership changed brakes and rear axle leak in brakes,this defect has reoccurred, this defect is a potenial for an accident. *ak
 When brakes are applied on unusual rod conditions and roads with ripples, they resist. the dealer and the manufacturer have been contacted about the problem.*ak
2
 When applying force to the brake pedal while traveling on pavement, the vehicle intermittently pulls to the right, consumer also experiencing problems with stopping the vehicle. *ak *slc
09/01/19974
 Consumer can be driving when needs to make a panic stop brakes will not work properly, takes about 20 sec to make stop. needs to leave pressure on brakes in order to stop. dealership changed vacuum chamber,but defect still is occurring. *ak
2
 When applying the abs brakes on normal road condition the pedal will travel to the floor, causing extended stopping distance. the dealer replaced the master cylinder on two occasions which did remedy the problem. please give any further details. *ak
 When brakes were applied at 15mph vehicle did not stop and rear ended vehicle in front of it. dealer saw nothing wrong. *ak
 When applying the abs brakes on wet or dry pavement the pedal will travel to the floor, causing extended stopping distance which could result in a vehicle collision. please give any further details.
10/09/19973
 Consumer at approx 55 mph went to apply abs brakes, brakes went to floor. had to pump brakes in order to slow down, started to jump. this would occur when ever hard braking was necessary. *ak
0
 When appling the brakes they feel mushy, can feel the brakes letting go and pick up again when applying them. when making sudden stop the brakes make chatter noises. *ak
06/01/1996
 Ea95-026, the braking system malfunctioned intermittently twice in 2 years which almost caused an accident. dealer cannot determine problem. *ak
08/22/199706/24/1993
 Abs brakes failed in an emergency situation at less than 10 mph, resulting in a collision. *ak
07/10/1997
 The truck has abs brakes; the driver was trying to stop and the vehicle kept going with the brake pedal being depressed, causing an accident. *ak
12/10/1996201/26/1993
 While driving applied the brakes and heard the abs kick in, and the pedal went to the floor and the vehicle did not stop. the vehicle kept on going about 10-15 feet before coming to a stop. this has happened twice to the abs. *ak *jb
112/01/1993
 Antilock brakes failed.
01/01/1997100
 Intermittent abs brake failure. *ak
04/01/19961109/01/1993
 Antilock brakes locked up 11 times, once causing accident.
04/18/1997604/01/1993
 Antilock brakes failed 6 times, once causing accident.
01/01/1996
 Abs brakes lock up/fail.
105/01/1993
 Antilock brakes malfunctioned, causing extended stopping distance.
11/01/1996
 Ea95-026, abs brake computer failure, caused the pedal to go the floor, complete loss of brakes, replaced complete braking system. abs light comes on and regular brakes come on red. *ak
05/01/1994
 Upon making a sudden stop and applying force to the brake pedal the anti-lock brake system kicks in, causing extended stopping distance and pulsation in the brake pedal. *ak
11/06/19951
 Antilock brakes malfunctioned.
10/17/1995303/01/1994
 Poor performance of abs caused vehicle not to stop on three occasions while pulling trailer.
01/11/1997203/01/1996
 When applying the abs brakes in the snow or wet wheather the brakes will locked up, once causing the consumer to run a traffic light, resulting in an accident. *ak
01/13/1996302/23/1995
 Ea95-026 brake failure, on wet surface and low speed applied brakes and the rear abs brakes locked up, in for repairs 3 times. *ak
 When applying brakes the vehicle did not stop. it rearended another vehicle. *ak
05/15/199310007/02/1993
 When applying brakes hard, heard loud grinding noise, pedal goes to floor, vehicle keeps moving, intermittent problem, according to dealer, brakes are working normal, no crashes, happens any speed. *ak
5
 On (5) seperate occasions, abs brakes failed to stop, resulting in extended stopping distance. abs designed by kelsey hayes. dealership says this is normal performance. please describe details. *ak
 Has no control over vehicle when abs brakes kick in. *ak
 When applying the abs in snow or any wet weather the abs locked, causing an accident. please describe details.
01/01/1995
 Ea95-026 active, abs brake failure, when brakes are applied,they pulsate, and vehicle pulls from right to left; there is also extended stopping distance on dry pavement. *ak
01/10/19970
 Riving vehicle, had stopped, pulled onto road, notice bend & started to slow down, heard mealing noise (abs working), pushed brakes, vehicle picked up speed, kept vehicle straight, went over embankment, had no brakes, finally hit tree. notified dealer. *ak
12/15/1996
 When applied anti-lock brake system engages, stops/ normal braking momentarily, causing extended stopping distance, intermittent problem, according to dealr, brakes are operating normally. *ak
11/05/1995104/19/1993
 Antilock brakes failed, causing accident.
06/01/1996806/01/1996
 Ea94-038 active, abs brake failure, when going over bumps on highway, loss of effectiveness, pedal goes to the floor, resulting in extended stopping distance. *ak
12/01/1995207/01/1993
 Abs brakes failed, vehicle would not stop on low traction under normal winter road conditions. *ak
 When applying the abs brakes in a sudden stop situation, the vehicle brakes failed. *ak
08/01/19931008/01/1993
 When abs are applied the vehicle begins to stop, then suddenly the brakes release as if vehicle was hit from the rear. ea95026. *ak consumer states vehicle begins to stop then suddenly the brakes release as if you were being hit from the rear.*jb
11/06/1994
 Driving along and getting ready to make a left turn, person in front made a sudden stop, hit brakes and the pedal went to the floor, the vehicle did not stop, the brakes just failed and vehicle rammed into the back of the car . *ak
108/02/1996
 When vehicle is crancked and m0ved the abs brakes make a funny noise when 8 mph is reached. *ak
06/06/1996
 When braking normally on dry pavement the brakes chatter as if they were on ice and the vehicle will not stop. the system has abs. this happens intermittently, once resulting in an accident. *ak
11/15/1996
 When applying the abs brakes, in a sudden stop situation, the vehicle brakes failed, causing an accident. *ak
 While driving, when pressing on the abs brakes, action seems inadequate, pedal becomes spongy and when brakes activate, vehicle speeds up. *ak
 While driving normal braking experienced, abs brakes malfunctioned when pedal pulsated while applying brakes. *ak
11/09/19960
 Consumer was driving down street and applied her abs brakes and nothing happened- consumer ended up going through a red light, lucky no traffic .*ak
 At a sudden stop the abs brakes grab for a second; have to gear off in order to stop . please describe in detail. *ak
 When applying the abs brakes, the vehicle brakes failed. please describe. *ak
10/01/1996
 Abs brake failure, ea94-038 active, when brakes are applied pedal goes to the floor, also when applied pulls very hard to right or left, in for repairs, changed the computer for abs system. *ak
110/01/1992
 Vehicles abs braking system failed with hard pedal going to the floor, then after almost hitting another car the brakes finally worked. ea95-026. *ak *jb
09/13/1993
 While driving applied the abs brakes and the vehicle will not stop. under investigation (ea 95 026). *ak
01/01/1995201/01/1993
 Antilock brakes failed, causing accident.
09/16/1996
 When applying abs brakes, the truck pulls to the right. please describe. *ak
08/08/1996305/10/1996
 Antilock brake system failed to stop vehicle, causing accident/injuries.
08/07/1996101/01/1993
 Rear seals failed, allowing fluid to collect on rear brakes; also cabs/axle seals leaked on rear brake shoes and drums. *ak
08/16/1996109/10/1992
 Extended stopping distance when applying brakes on wet roads.
01/23/19963
 Antilock brake system failed, causing accidents. *dsh
03/21/199510
 Abs brakes do not slow vehicle. in both failures, vehicle was going down steep driveways, abs buzzed then accelerated/ also sensitive to any dirt/ripples *ak
12/01/19931
 Antilock brakes fail to stop brakes from locking up in emergency stops.
04/01/19951
 On bumpy roads, antilock brake system causes brake pedal to go to floor/extended stopping distance. *dsh
04/17/1996
 Ea-95-026 active, abs, brake failure, impact 12:00, speed 20 mph, extended stopping distance. *ak
03/01/19931
 Anti-lock brakes fail often on hills, gravel, or wet roads, almost causing accidents. *dsh
 Sometimes when applying the brake, there is no brake, have abs anti-lock brakes. please describe .*ak
12/01/1993
 Abs; failure on the abs brakes, cannot stop the vehicle, causing the consumer to have a near accident ea95-026. *ak
 Abs brakes; on bumpy road surfaces, brakes release, do not stopping properly. please describe details. *ak
11/15/1994
 Abs: anti-lock brake system is failing to stop vehicle within a reasonable distance when performing a hard/panic stop; hear grinding noise, no warning. *ak
 Abs-brakes - while driving about 30mph coming around the curb the owner tried to appily brakes and the brakes went to the floor, the car would not stop. *ak
02/01/1996
 Ea95-026, brake failure,driving at speed of 55mph, pedal went to the floor, loss of effectiveness, *ak
02/12/1996
 Abs system failure, experience excessive stopping distances
09/01/19951
 Anti-lock brakes failed 3 times, resulting in loss of control/accidents. *ak
 Abs brakes; brakes fail upon long braking or uneven road surface, brake pedal goes to floor. please describe details. tt
07/24/19954
 Abs brakes failed. *sd
01/03/1996
 Abs brake does not respond during sudden stop on wet pavement, resulted in two different accidents. tt
09/01/1995
 Abs system failure, partial loss of braking, equipped with abs brakes. tt
 #pe95-023 when applying the brake it doesn't stop it slows the truck down . tt
 #pe95-023 the performance of the brake it slows the truck down it doesn't stop have abs anti-lock brake . tt
 #pe95-023 when apply the brake goes to the floor and locking up have abs anti-lock . tt
12/03/1995
 Ea95-026, active, brake failure when brakes are applied vehicle will not stop, loss of effectiveness, impact 12:00 position speed 35mph. tt
11/25/1995
 Abs brakes release completely, resulting in an accident. tt
 Abs braking problems. please describe. tt
11/27/1995
 The brakes do not have the power to stop the car. tt
11/22/1995101/01/1993
 Poor braking performance of the vehicle equipped with abs. it takes a long/distance to stop . tt
6
 Abs braking problems. tt consumer states he was braking and he was standing on the brakes, which first grabbend and then released almost causing an accident. *slc
08/01/1995201/01/1993
 Vehicles abs braking system intermittently malfunctioned with soft pedal and long extended stopping distances. tt consumer states one one occasion there were no brakes.*jb
10/21/1995
 Vehicles abs braking system in a sudden stop car did not slow down and caused a 5 car accident.(ea95-026). tt
11/11/1995204/08/1993
 Abs braking problems. tt vehicle stopped suddenly in front of consumer, when consumer applied brakes they failed and caused an accident. transfer case failed. *slc
11/13/1995
 Poor braking performance of the abs system. tt
06/07/19957
 Anti-lock brake design, causes braking problems. *skd
08/01/1995
 Abs, brake failure, when brakes are applied skided and have extended stopping distance, impact 12:00, spped 25 mph. tt
10/23/1995
 Consumer was driving when applied the brake failed have abs anti-lock brake . tt
 Abs brakes; brakes very slow in responding w/screeching noise. extended stopping distance is questioned. please describe details. tt
 Vehicles abs braking system pedal feels mushy and unordinary long stopping distance.(ea95-026). tt
10/21/19952
 Abs system failure, difficulty stopping the vehicle, excessive brake pedal travel. tt *slc
11/02/1995
 Abs system failure, the rear wheels do not stop vehicle, only the front wheels are working. tt
10/01/1995
 Abs, brakes when applied experience brake lockup, or uneven surface. tt
10/31/1995
 The truck has abs. the stopping distance has increased and makes alot of noise when applied. please describe. tt
212/17/1992
 Abs braking problem. tt clunk in rear brakes, consumer states they do not feel right, dealer attempted to correct however failed, noise still exists. *slc
 Abs braking problem. please describe. tt
10/01/1993406/01/1993
 Abs brakes; on (4) occasions, brakes system has failed completely on dry pavement.tt on four occasions have stepped on brake pedal and pedal went to the floor.*jb
2
 Abs brakes; brakes completely malfunctions on gravel icy and snow roads and poor effectiveness. owner identifies several near misses. tt when applying brake on icy or snow or gravel road, the brake make buzzing sound and failed completely and the vehicle goes out of cotrol. *yh
 Abs braking system malfunctions on bumpy roads and has long extended stopping distances.now when braking truck pulls to left. tt
 Anti-lock brakes lock up on wet pavement, causing vehicle to go out of control. *ak
11/15/1994110/30/1993
 Consumer was driving applying the brake pedal went to the floor and rear ended the car in front. tt vehicle had been to dealer prior to accident regarding brake problems, dealer had resurfaced rear drums, sanded lingings, and replaced front brake pads. engine revs to 1500 rpms after sitting 20 to 25 minutes, engine runs rough. seat belts do not always retract. transmission shifts hard. when air conditioner is on medium or high, vehicle's engine revs to 2500 rpms on acceleration from a stop. *slc
09/01/199310
 #pe95-023 poor performance of anti lock brakes. tt dealer stated to consumer that abs feels different when making panic stops . *slc
06/15/1995
 Abs:when anti lock system comes into play, brakes do not stop vehicle; pedal tends to go to floor; rearended another vehicle. tt
10/01/1994
 Abs system malfunction, left wheel locked up when braking. tt
 Abs brakes fail at various times. tt
01/01/1994
 Having problem with poor brake performance with the abs system. tt
09/12/1995
 Only going 20mph vehicle stopped short in front of owner applied abs brakes and they failed. tt
06/01/1995
 Pe95-023 active, brake failure applied extended stopping distance, impact 12:00 speed, 30 mph. tt
 Experience intermittent abs brake failure, when front wheels lockup under normal application of brake, wet or dry conditions. tt
11/15/1994
 Abs: erratic braking; brake lock up; brake warning light comes on when there's no obvious brake problem present. tt
08/01/1995
 Abs, brakes failure, impact 12:00 position, speed 25 mph, loss of brake effectiveness, pe95-023 active. tt
08/01/1993
 When brakes are applied, vehicle continues to move at least two car lengths. (abs). tt
 Vehicles abs braking system malfunctions on bumpy roads locks-up.and also takes longer stopping distance. tt
09/05/1995
 Abs system failure, total loss of braking in the rear brakes. tt
08/29/1995
 Pe95-023 active, loss of brake, impact 12:00 position speed 15mph, (abs). tt
08/28/19952
 Abs brakes; brakes fail w/soft pedal and poor response. also when pavement uneven. tt
04/01/19951
 Experiencing extended stopping distance. tt
01/01/1995
 Abs,pe95-023 active, brakes failure intermittently makes a loud noise, has extended stopping distance. tt
 If you press on the brake truck feels like the brake will not stop it has abs anti-lock brake . tt
 Consumer was driving came to a stop there was no brake pedal went to the floor there was a noise has abs anti lock brake . tt
08/01/19953
 Consumer was driving and came to a stop, there was no brake, pedal went to the floor,there was a noise, has abs anti lock brake . tt
04/01/1994
 Abs system failure, loss of braking at low speeds. tt
06/15/1995
 Brakes make grinding sound feels like pedal goes to the floor. no response from anti lock braking system. tt
05/26/1995
 Abs system, applied pressure to brakes during emergency stopping, brakes grab and than a loud noise, then pedal fade out, resulting in accident. tt
05/15/19951
 Abs system failure, loss of braking ability at low speeds. tt
03/01/1993
 Abs, brake failure in wet road condition intermittently on dry road condition. tt
01/01/1995
 Abs, brake failure , experience lockup when brakes are applied, impact 12:00 speed 5 mph. tt
03/13/19954
 Abs brakes failed to stop vehicle when applied, causing extended stopping or inoperative. repaired 4 times. tt
03/01/19952
 Abs brakes fails to stop vehicle when applied causing extended stopping, loud popping noises and inoperative. tt
06/23/1994
 In times of extreme emergencies the anti lock and braking system are inoperative. tt
05/01/199411
 Anti-lock brake problems, causing brakes to fail intermittently. *skd
11/18/19941
 Abs system malfunctioned during normal stopping,vehicle experienced long stopping distance periodically, dealer said nothing is wrong. tt
05/19/19931
 When abs was applied in an emergency situation, brakes failed to release fully, resulting in accident/injury. *ak
12/01/19931
 Vehicle experiences long stopping distance, dealer said abs operation is normal. tt
SERVICE BRAKES, HYDRAULIC - ANTILOCK - ABS WARNING LIGHT
06/26/1995108/02/1993
 Abs warning light illuminates. *sd
SERVICE BRAKES, HYDRAULIC - ANTILOCK - CONTROL UNIT/MODULE
06/01/1994
 Ea95-026, the vehicle's abs system fails, resulting in the pedal touching the floor and the vehicle not stopping which can cause an accident. *ak
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS
105/01/1993
 Brakes failed, on several occasions, one incident resulted in rear end collision, the seat belts broke during collision. yh
11/04/19981
 Brakes failed causing consumer to rear end a stalled vehicle. nlm
01/06/1997209/01/1992
 Vehicle pulls when brakes applied, brake pads/fluid/calipers and rotors replaced, however problem continued, brake hoses replaced.
301/01/1993
 Anti lock brakes continually failing, replacement of the front wheel brakes did not rectify abs failures.
11
 Brakes failed.
04/01/1995202/01/1994
 Brakes lock up in rain/snow, also on gravel roads.
10/01/1996106/01/1993
 Brakes pedal went to floor upon hitting bumps in roadway.
05/29/1996
 When applying the brakes the pedal goes to the floor and there is extended stopping distance. under investigation ea 95026. *ak
108/02/1993
 Vehicle veers to the side when brakes are applied. *sd
 Experiencing intermittent brake failure. *ak
02/01/1993
 Experiencing extended stopping distances. tt
 While driving, experience brake failure when made attempt to slow down, pedal went to floor, no prior warning. tt
 When braking, pedal goes to floor. had in twice, still is not fixed. tt
01/01/1994
 Brakes make loud noises with normal use. tt
06/12/1993
 Intermittent problem. depressed pedal brakes went to the floor resulting in extended stopping distance. describe in more detail. tt
08/27/19931
 Heard humming noise when brakes were applied, also pedal went to the floor. tt
01/10/1995
 Brakes do not always stop the vehicle. please describe details. tt
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC
08/01/1999
 No summary listed for above vehicle. *ak
11/12/1997506/01/1997
 Windshield wipers constantly shut off when it starts raining, the only way to get them to work is to stop the car and get out and manually force them to work again. they will work for a little while then do it again. the grill : the crome is pealing off of the grill. the brakes; there is intermittent problems. one is the disc keep warping after they have been repaired. they sometime fail to stpo the car as they should. the pedal goes to the floor while trying to stop.*ak
03/01/20001
 While driving at a approximately 30 mph and brakes are hit, vehicle starts to violently shift to the left. brakes/calipers, and anti-lock brake valves have been replaced. also, rotors were turned by dealership at consumer's expense. manufacturer has a shop bulletin issue to dealership for remedy of problem, but problem still occurs. there has not been a recalle issued. this defect does not allow consumer to stop appropriately, and can cause a serious accident. *ak brake hoses failed. brake fluid was out again after replacing it. *yh
03/02/20001506/01/1993
 Over the entire time that we have owned this vehicle, the brakes and the abs system have not operated reliably. whenever the vehicle is being driven on an irregular or wet street (even at low speeds, below 30mph), and the brakes are applied, the brake pedal will go to the floor and all braking effect vanishes momentarily. this definitely involves the abs system, because there is the characteristic vibration of the pedal when the system is activated. abs activation during these episodes is inappropriate, ineffective, and dangerous to the occupants of the vehicle. *ak
01/07/19939
 Ea95-026; consumer experiencing excessive wear of the front brake pads and rotors. also, upon making a sudden stop, consumer noticed extended stopping distance/ brake fade away. consumer has contacted the dealer. *ak
06/06/19934
 Abs brake problems; intermittently; while driving on regular road conditions, during normal braking when applying the brakes, the pedal almost reaches the floorbroad and system will kick in and stop. the vehicle surges forward before it stops. the front brakes pads have been replaced (4) times in 70,000 miles. both calipers have been replaced, and the rotors on the right side. consumer is still experiencing a braking problem. *ak
06/05/1996
 Vehicle is loosing brake fluid. at 31 thousand miles the vehicle has no wear on the front brakes.*ak
 Front brakes failed-brakes would not release-(consumer has abs brakes) no injuries was sustained. *ak
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - CALIPER
101/14/1993
 Brake calipers failed.
 When applying the brakes in emergency stopping on wet or dry pavement the pedal will travel to the floor, causing extended stopping distance, resulting in an accident, mechanic states that the caliper is bad. please attach repair information. *ak
07/25/1995108/02/1993
 Brake pads/calipers/master cylinder replaced due to failure. *sd
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - PADS
301/14/1993
 Brake pads failed three times.
 Abs brakes; when applying the brakes under normal conditions, the pedal goes to the floor and the brakes fail to stop the vehicle. replaced brake pads. *ak
01/16/1996103/01/1994
 Brake front disc pads were worn/rear brakes need adjustment.
04/01/1994105/01/1993
 Brake pads replaced.
07/25/1995108/02/1993
 Brake pads/calipers/master cylinder replaced due to failure. *sd
01/01/1993
 Experiencing delayed braking reaction. front brake pads and rotors replaced four times. tt
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - ROTOR
201/14/1993
 Brake rotors failed twice.
04/01/1994105/01/1993
 Brake rotors replaced.
09/12/1995305/01/1993
 While driving vehicle the rotors cracked and the brakes failed. pushed on the brakes and there was no reaction with the stopping of the vehicle, ea 95 026. *ak
08/17/19957
 Brake rotors failed. *ak
05/01/19951
 Premature wear of front brake rotors. *ak
01/01/1993
 Experiencing delayed braking reaction. front brake pads and rotors replaced four times. tt
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM
06/18/1997109/01/1992
 Brake shoes replaced and drums de glazed.
01/16/1996103/01/1994
 Brake front disc pads were worn/rear brakes need adjustment.
08/07/1996101/01/1993
 Rear seals failed, allowing fluid to collect on rear brakes; also cabs/axle seals leaked on rear brake shoes and drums. *ak
06/01/1995
 Rear brake seal broke and leaked brake fluid over rear brakes. tt
04/01/1995
 Pe95-023 active, extended stopping distance at low speed, and rear locked up. tt
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - HOSES, LINES/PIPING, AND FITTINGS
03/01/20001
 While driving at a approximately 30 mph and brakes are hit, vehicle starts to violently shift to the left. brakes/calipers, and anti-lock brake valves have been replaced. also, rotors were turned by dealership at consumer's expense. manufacturer has a shop bulletin issue to dealership for remedy of problem, but problem still occurs. there has not been a recalle issued. this defect does not allow consumer to stop appropriately, and can cause a serious accident. *ak brake hoses failed. brake fluid was out again after replacing it. *yh
01/15/1997
 Brakes still pull, replace hoses,lube brakes.
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - MASTER CYLINDER
07/01/19983
 When applying brakes pedal feels soft and spongy. brakes failed 3 times, no accident. vehicle taken to dealer twice for this problem, found no problem the first time. second time, master cylinder was replaced. six months after last repairw were done, brakes were fine, then brake failed again.*ak
05/05/1996305/01/1996
 Whenever braking on dry pavement abs would kick in without warning. vehicle would fail to stop, resulting in extended stopping distance. took to dealer & had the master cylinder replaced for the third time after it was blown twice in one month. had everything in the brake system was checked, fluids replaced, rotors turned, etc. dealer is unable to identify problem. *ak *ml
08/17/19991
 When the brakes were applied in a panic stop , the driver heard a loud noise, pedal became soft and went to the floor, causing extended stopping distance which resulted in loss of master cylinder. the dealer has replaced the master cylinder. *ak *ml
08/11/1997306/01/1993
 Master cylinder replaced three times and currently having same problem. *ak
07/01/199303/01/1993
 The problem with the abs brakes is ongoing, there is no fix. when going down a slight incline on the road, and if the road has some slite ribbing or wash board effect, the brakes fail completely if used in a panic stop situation, even if one continues to push the brake pedal as instructed with abs. also medium ie 50 mph panic stops also have the same effect. the problem seems to be a long hesatation before the abs starts its cycle of braking, and any road irregularities or road sand increases this hesitation before the abs starts its braking cycle. it should be noted that the master cylinder was changed early in 1993 to no avail. it would appear to be a software problem in the abs logic controller. *ak
3
 When brakes are applied in a panic stop the master cylinder blew out, resufied. *ak
07/01/19971202/02/1993
 Master cylinder failed.
07/01/19972
 Ea95026, the defective abs braking system malfunctioned, causing the pedal to touch the floor, noises and extended stopping distance which may cause an accident. dealer replaced brake master cylinder 2 times. dealer cannot determine problem. *ak
 When applying the *ak
01/01/1994105/01/1993
 Master cylinder replaced due to brake failure.
07/25/1995108/02/1993
 Brake pads/calipers/master cylinder replaced due to failure. *sd
10/01/1995106/01/1993
 While driving, at approx. 15-20mph, suddenly master cylinder failure occured when pedal went to floor, without prior warning. tt master cylinder was replaced by dealer.*jb
SERVICE BRAKES, HYDRAULIC - PEDALS AND LINKAGES
2
 Prior to recall brakes failed, causing accident, recall #01i006000. the consumer is still waiting for the parts. *yd
06/15/20011
 Consumer received recall 01i006000 notification concerning brake pedal feed. dealership did not have component available to correct defect. please provide any additional information / attachments.*ak
09/18/19958
 Brake pedal becomes hard during emergency braking, resulting in extended stopping distance. *ak
SERVICE BRAKES, HYDRAULIC - POWER ASSIST - VACUUM
09/03/1997305/01/1993
 Going 30mph when brake light came on. the hydraulic booster did not work; had to press on brakes hard to stop vehicle. took to dealer & had computer replaced. *ak left front seat belt would not retract at times. *slc