Recalls


CampaignManufacturerManufacturing dateType# of units affectedDate Owner notified MfgRecall Initiated byManufacturers of recalled vehicles/productsReport Recieved DateRecord Creation DateRegulation Part NumberFMVSS Number
SERVICE BRAKES, HYDRAULIC - ANTILOCK
96V074000CHRYSLER CORPORATIONfrom 08/01/1994 to 08/30/1995V (Vehicle)9000007/08/1996MFRCHRYSLER GROUP LLC05/02/199605/03/1996
Defect SummaryCorrosion of the abs hydraulic control unit can cause the solenoid valves to stick in the open position.
Consequence SummaryIf either front wheel valve sticks, the vehicle would swerve from a straight stop when the brakes are applied.
Corrective SummaryDealers will install a plate and silicone grease injected into the solenoid cavity to eliminate the potential for this condition.
NotesOwners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time, should contact chrysler at 1-800-853-1403.also contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393.
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - MASTER CYLINDER
96V075000CHRYSLER CORPORATIONfrom 08/01/1994 to 10/01/1995V (Vehicle)15180006/10/1996MFRCHRYSLER GROUP LLC05/03/199605/08/1996
Defect SummaryThe brake master cylinder can leak brake fluid due to a damaged double lip rear piston seal.
Consequence SummaryBrake fluid leakage can result in diminished effectiveness of one half of the split brake system. the instrument panel warning light(s) will signal system impairment prior to partial brake system loss.
Corrective SummaryDealers will replace the rear brake master cylindr piston assembly.
NotesSystem: brakes; hydraulic; master brake cylinder. vehicle description: passenger vehicles. includes neon vehicles equipped with the acr competition package only. note: owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time, should contact chrysler at 1-800-853-1403. also contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393.

Bulletins


BulletinBulletin dateReplacement BulletinItem no.SummaryAdded
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS
05079906/25/1999606160Brief information on the use of asbestos fiber brake linings. *tt08/11/1999
CH05059505/01/199543074Unknown11/01/1995

Consumer Complaints


Fail datemilesoccurencesPurchase date
SERVICE BRAKES, AIR - ANTILOCK
10/01/1998105/01/1995
 Many many problems with this vehicle
12/03/1997108/01/1996
 Also.....water pump failure.....3/6/99....mileage....67,500. the listed incidents are unusal and unexpected. it seems i am having one problem after another on this vehicle. dealer has worked with me and has been more than fair. i am happy with their service. i am not happy about the quality of the product chrysler has created. i believe that i am paying for their design flaw, as this is the first year of totally new designed vehicle.
01/12/1999108/01/1995
 Chrysler wants us to be responsible for 50% of charges to repair only the transmission; which was already overhauled at 35,000 miles. we need help in getting chrysler to take responsibility for a possible lemon. the power steering pump is going out and the dealer said it is premature; chrysler will not even acknowledge. the abs brake light comes on and stays on at different times, the front of the car jumps upon slowing to stop. the car has been nothing but trouble.
SERVICE BRAKES, AIR - ANTILOCK - ABS WARNING LIGHT
09/02/2004119000412/16/2003
 Rpm's running high, transmission slipping, rough idle, abs light consistantly on even after inspection, gear slips when placing into park, while driving the car reversed on its own. have complained and wanted into another car due to having this one on a 24 lease, they denied me and have had to drive it and with 3 children and myself in the car it is not safe, but is the only transportation we have. we need help resolving this problem. *ak
SERVICE BRAKES, AIR - DISC - ROTOR
07/12/1995
 Front brake rotors are warped, causing pulsation when brakes are applied.
SERVICE BRAKES, HYDRAULIC
03/04/2006122150710/16/2004
 I've had my engine checked back in may of 05 by the dealer they said it was engine misfire,the distributor ignition was bad. they charged me $321 just to check it,then i paid $276 to get it fixed. the car has had a drip ever since. in the past 6 to 8 months or longer i've had a drip from the engine that can't be fixed , i recently had my car worked on it was in the shop for a month it cost me $2500 to repair and it still has a leak. it's back there again because it needs that expansion plug and retaining bracket that only the dealer can provide according to every site but the place the car comes from. i'm also having transmission problems which i've had since i brought the vehicle. because i need a shift mechanism and cable from the dealer according to every site but where the car comes from. a few of the problems that are on the list i've either got fixed or got an estimate for.(one ) of the problems on the list ,the dealer sent something in the mail and i got it taken care of by the dealer,it was the( trans. floor shifter). also on your list! i've spent a lot of money to repair this vehicle for mistakes made by the dealer and it's not fair . i would like to be reimbursed and the recall problem fixed. *nm
11/15/20030
 I don't have time to go back through the thousands of dollars worth of receipts for this lemon that has had every major component fail multiple times. the latest is the 3rd transmission failure since 1995.
630002
 When brake pedal was depressed they didn't move and vehicle didn't stop. cause unknown.*ak
04/02/200368388112/06/1994
 While driving down the interstate, it suddenly sounded like there was an increase in road noise, then suddenly there was a puff of smoke from the back and the noise disappeared. stopping to check, my master cylinder was half-empty. per chrysler dealer who repaired it, right rear brake came apart (cylinder blown and springs broken). when it failed, it also damaged right rear tone wheel and sensor, making the anti-lock brakes inoperative. there was no warning before this catastrophic brake failure. *jb
SERVICE BRAKES, HYDRAULIC - ANTILOCK
09/01/2004105/01/2001
 Dealership refused to honor recall for abs brake repairs. *mr when the consumer purchased the vehicle, the abs light was on. *sc *jb
07/01/2002
 Nhtsa recall 96 v 075-000/manufacturer's recall 687 concerning abs hydrulic master cylinder:recall repair was not completed.feel free to provide any further information.*ak
08/26/2002
 Anti lock braking system light appears on dashboard until vehicle is turned off. dealership is aware of problem.*ak
 Dealership examined anti-lock brake system and determined that brake fluid is not reaching rear-brake system. component causing this problem to occur is called the hydromatic control unit, and is reported to be on a national back-order. please provide any additional information / documentation.*ak
08/01/1997
 Brakes-driving on several occasions brakes will make a grinding sound and go to the floor, and will finally stop. had brakes replaced often, because they wear down often. battery- had to replace battery several times, because something causes battery to go dead. engine-driving at different speeds or sitting at stop signs and lights car will stall withot warning, took car to the shop, could not find problem, also called manufacture. electrical system-gas gauge shows empty when car is full, check engine light comes on, radio in car would go off when you hit a bump, finally stop working ,dash lights come on and off. air conditioner-have had several problems with air conditioner, have had different parts replaced,when sitting with air on car tries to go died. transmission- car leaks fluid, can't find spot, while driving up a hill transmission will slip is hard to pull, have had many problems out of car and sent to car repair shop many times. *ak
06/08/2001
 Vehicle was in park with engine running, consumer applied brakes, and put vehicle in drive. suddenly engine revved, and vehicle surged forward, pedal to floor. vehicle hit a couple of curbs, went airborne about 32 ft, then, landed in a 15 ft deep ditch. damage $ 666.00, no injuries.*ak
03/16/20011
 Consumer was traveling on highway and abs braking light system came on. she took vehicle to a mechanic, and he told her that master cylinder piston and hydraulic chamber malfunctioned. this vehicle wa snot included in manufacturer's recall 686. *ak *slc
02/05/2001
 After slamming on brakes abs light came on. currently, has regular brakes, but no abs.*ak
02/08/20012
 After applying brakes abs system did not release after each brake application which caused brakes to fail and the vehicle to fishtail, resulting in a collision. *ak consumer states the brake lines collapse, rear brake adjusters failed. *slc
09/01/19961801/27/1995
 While depressing brake pedal, vehicle would begin to slow, a click sound is heard and the pedal seems to lock and vehicle does not slow for a period of seconds, dealer can not find any problems and states that brakes are working as normal. *slc
07/24/20000
 While driving could step on brake pedal and would hear noise coming from the rear like grinding metal to metal. *ak
07/08/20002
 While driving abs braking system malfunctioned, causing abs light to come on and the brake pedal to travel to the floor, and vehicle acclerated which may have caused a crash. to stop vehicle, emergency parking brake had to be applied. mechanic fixed an abs right sensor. problem is still occurring.ak
403/01/1996
 Have had the brakes repaired 4+ times and still not fixed. have spent $1500.00 just on brakes not to mention other problems such as transmission. this is the worst car and i will never buy chrysler product again. no help from manufacturer. contacted each time. i just wish the brakes would be fixed before a major accident is caused. *ak
06/06/2000
 Recall 96v075000/brakes:hydraulic:master cylinder: brake failed while driving at 35-40 mph, forcing vehicle into an field to avoid a collision. but, five passengers sustained minor injuries; dealer notifed. feel free to provide further details. *ak
03/05/2000301/01/1995
 Hydraulic noise under hood as brakes applied, brakes failed to stop car, caused minor crash, leaking master cyl replaced, brakes failed again twice, chrysler replacing computer module governing brake hydraulics, would not confirm this would cause brakes to fail
11/01/1999106/01/1996
 Noise detected same week car purchased replaced once, but noice continued until present, dealer informed of noise from beginning and several times and also manufacturer but problem presist. dealer said could not do anything because noise could not be reproduced wich then was reproduced but was considered normal but problem caused accident accident also problem with brakes wearing out too fast. *ak
12/17/1999106/01/1998
 Complete steering failure at left frt wheel, luckily i was backing when it occurred. abs light on braking system indicates a problem, pulls when brake is applied
508/01/1995
 Bendix antilock brakes failed causing them to make grinding noise. nlm
05/15/1998101/01/1995
 These incidents seemed to go all about the same time. the abs light still will not reset. the brake light on the dash comes on intermittently. the electronic control module on the hydraudlic secquencing valve was found to be inoperative. the ecm module was defective. the fuel pump electrical 4-pin connector on the fuel pump within the fuel tank showed discoloration . the fuel tank low level light was 'adjusted', never has been accurate. fuel
03/14/1998401/08/1998
 Abs hydraulic unit and module failed. mjs
04/28/1999105/01/1995
 Abs brakes not operable, increased stopping distance. abs light on constantly since date indicated, dealers say no safety issue and will not repair under warranty. notification to chrysler corp.
06/20/1998207/01/1995
 Abs warn lite on cost $300.00 + 1st time 2nd time , want $300.00+again no end to this could lead to fatal crash when or if wheel does not perfom as required during hard stopping. please review problem as it is costly because of many components in abs system and mechanics seem to have trouble fixing problem 1st time around.
10/01/199809/07/1995
 Vehicle experienced 3 sidewall tire blowouts. in addition, abs module/ transmission failures.
07/31/1998405/19/1996
 Brake failure due to abs module failure.
04/01/1998106/01/1997
 Anti lock brakes failed causing loss of control.
01/27/1998308/09/1997
 While driving vehicle the consumer tried to stop at a red light when she stepped on brakes pedal, the pedal went all the way to the floor, and vehicle did not have any brakes. consumer had taken vehicle to dealer a few times for the same problem. *ak
101/01/1995
 Master cylinder replaced, however problem still exists. the pedal feels spongy and goes too far to the floor.
07/29/1997108/08/1995
 Brakes unable to stop vehicle.
11/08/1996205/01/1995
 Front abs brakes failed twice.
5
 Abs brakes lock up and occasionally grind when stopping; also, premature wear of front brake pads. in addition, vehicle experienced power steering fluid leakage;insufficient lighting from heaflights and check engine light constantly comes on due to wiring problems. *ak
09/17/1997
 When car has been running for a while the abs light comes on. owner is not experiencing braking problems. the dealer has been contacted. *ak
07/01/1997203/20/1995
 Abs light comes on while driving or when stopped with foot on the brake.
 When applying the abs brakes at any speed, the pedal goes to the floor and there is extended stopping distance. please provide details. *ak
 Owner received recall notice, contacted dealer and was told that the parts were not available. recall#96v074000. *ak
02/19/1997
 Recall 96v075000, after having recall work performed on 1/31/97, the brakes failed and caused owner to have an accident on 2/19/97. mechanic stated that brakes were in bad shape. *ak
10/01/19963
 Driving, tried applying brakes, they took for a bit, then suddenly no brakes (abs); was unable to stop vehicle; steering wheel made whinning noises. took to dealer severaltimes for repairs. *ak
 Experienced loss of brake pressure while coming to a stop. *ak
 Owner has abs brakes, she states that her abs brake system failed , resulting in an accident after owner received recall notice. *ak
803/01/1995
 Engine failed 4 times; abs brake sfailed twice and the transmission failed once. *ak
112/20/1994
 When releasing the brake pedal, abs brakes squeal. *ak
11/12/1996
 Brakes locked up and caused an accident, has abs anti-lock brakes . please describe . *ak
12/06/19951
 Antilock brakes failed, causing accident/injury.
07/30/19961
 Abs brakes failed, causing accident.
07/30/1996
 When truning left on dry surface (abs) the brakes went out while trying to avoid another car . please describe more.*ak
06/23/1996105/01/1996
 While in drive,sudden acceleration forward took place, also no deployment of driver's air bag during accident, resulting in injuries and abs brake failure. *ak
11/15/1995
 Abs:front right brakes wear down metal to metal within 1,200 miles, replaced 3 times, excessive wear on one side, cannot press on brakes, *ak
 There is a delay on the abs anti-lock brake, received recall after the problem #96v074000, please describe . *ak
 Equipped w/abs brakes; four sets of brakes pads wear excessively w/rear brake cylinders leaking. please describe details. *ak
10/01/19953012/01/1994
 Failure of the abs system, causing no braking or partial braking and then the brake pedal to go to the floor and the wheels lock up. *ak *slc
12/01/1995
 Abs braking system; failure on the brake system, applied force to the brake pedal, the pedal was hard. *ak
09/10/1995
 Abs braking system; failure on the abs braking system, the consumer could not stop the vehicle. *ak
 While driving on dry pavement abs brakes kicked in when not suppose to. tt
 While applying brakes, the pedal went down to floor and there were no brakes for five minutes. please describe. tt
 While driving, at approx. 5-10mph about to turn, abs system malfunctioned, when pedal went to floor, allowing to hit another vehicle, no prior warning. tt
11/09/1995101/01/1995
 The vehicle has abs brakes and while driving the system went out and would not stop the car. tt brake light came on indicating a brake problem, consumer was driving on expressway, took vehicle to dealer, and it was discovered that master cylinder had to be replaced.*jb
 Abs braking problems. his son had an accident nov. 27. please describe. tt
05/15/1995
 Abs: brakes defective, need replacing, brake pad all way to rotor worn. tt
 The abs anti-lock brake has poor performance there is no air conditioner don't work purchase car new . tt
08/31/1995
 The car is new and with 15,000 miles on the car it needs a complete brake job. please describe. *ak
 Brake failed there was no warning have abs anti-lock brake some time the light comes on the wiper,radio and the air conditioner stop working purchase car new .
04/14/1995
 Consumer was driving and turn left applied the brake went to the floor pulled over parked car turn off turn back on there was brake have abs anti-lock . tt
01/23/19953
 Anti-lock brakes failed, causing loss of control/accident. *skd
03/03/19953
 Tried to stop the vehicle and the abs system failed and the car did not stop. tt
06/20/19953
 The brake pedal fall to the floor, have abs anti-lock brakes. tt
SERVICE BRAKES, HYDRAULIC - ANTILOCK - ABS WARNING LIGHT
02/01/199602/28/1995
 Abs brake light stays on for unknown reason.
SERVICE BRAKES, HYDRAULIC - ANTILOCK - CONTROL UNIT/MODULE
1
 The anti lock brake light illuminated constantly. the vehicle was taken to the dealership and they diagnosed the problem as a failed abs control unit. *jb
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS
05/08/2002
 While driving when brakes are applied they wouldn't hold due to enclosed bearings and brake cable system failing. dealer contacted.*ak
1
 While driving 40 mph, driver noticed a stopped vehicle, driver hit the brakes to avoid hitting the stopped car, brakes did not stop and vehicle hit stopped vehicle in the rear, rear wheels of stopped vehicle came off the ground, front airbags did not deploy, and the driver's seat belt did not lock, drivers forehead hit windshield. vehicle totaled. *tt
02/08/20012
 After applying brakes abs system did not release after each brake application which caused brakes to fail and the vehicle to fishtail, resulting in a collision. *ak consumer states the brake lines collapse, rear brake adjusters failed. *slc
105/20/2000
 Brakes squeaking. *mjs
 When driving at any speed and making making any type of turn there is a loud knocking noise coming from the front of the vehicle, and when applying for the brakes the noise is there. *ak
09/10/1999
 Braking system malfunctioned, causing the brake pads to burn out, also, a fire broke out due to brake fluid leaking out from a hose and spraying onto pads. *ak
02/25/1998
 While driving at a low rate of speed, the brakes were applied, the pedal went to the floor, resulting in extended stopping distances, causing the vehicle to collide. owner states that vehicle's abs system was replaced prior to collision. the dealer will be notified. *ak
112/16/1994
 Brakes failed.
1
 The brakes failed.
07/14/19961
 Brakes failed, causing accident.
11/20/19950
 Brakes wore out. *sd
 Brakes do not release properly. *ak
04/04/1996
 Consumer was driving on wet road, applied the brake and it failed, causing an accident. please describe . *ak
01/01/19951
 Brakes lock up. *sd
06/28/19951
 Brake pedal goes to the floor, brakes do not stop vehicle. *ak
01/23/19951
 Brakes did not work, lost control of vehicle, resulting in an accident/injury. tt
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC
10/27/1998110/13/1998
 Brake replaced and rotors turned, causing vehicle to pull while braking *mjs
11/01/1999106/01/1996
 Noise detected same week car purchased replaced once, but noice continued until present, dealer informed of noise from beginning and several times and also manufacturer but problem presist. dealer said could not do anything because noise could not be reproduced wich then was reproduced but was considered normal but problem caused accident accident also problem with brakes wearing out too fast. *ak
2
 Front brakes replaced twice.
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - CALIPER
07/07/2003401/15/2003
 After coming to a complete stop and releasing the brake the car will go into low gear and becomes very hard to accelerate. took it to a shop because it was said to be a brake problem, i got new rotors, front and back brakes, and calipers. problem still is there.*ak
12/13/1998
 The right brake caliper malfunctioned, causing more wear and tear on the brake pads, which may cause extended stopping distance. please provide further information. *ak
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - PADS
07/07/2003401/15/2003
 After coming to a complete stop and releasing the brake the car will go into low gear and becomes very hard to accelerate. took it to a shop because it was said to be a brake problem, i got new rotors, front and back brakes, and calipers. problem still is there.*ak
 Excessive wear of the front brake pads . consumer has contacted dealer on a number of occasions to have the pads replaced. please provide any further details. *ak
04/13/2000210/01/1997
 Car returned to dealer for 4th time for brake failure. in the past they have not found anything wrong. now, master cylinder to be replaced for 2nd time. brake shoes and pads were replaced for second time since 10/97 in 02/00, and already show excessive and uneven wear and need replacing again. even through total brake failure, the abs warning light has never come on. this car is a nightmare!
06/01/1997
 The rear brake pads and shoes malfunctioned, causing extended stopping distance, which may result an accident. been replace 2 times. dlr cannot determine the problem. please provide further information. *ak
5
 Abs brakes lock up and occasionally grind when stopping; also, premature wear of front brake pads. in addition, vehicle experienced power steering fluid leakage;insufficient lighting from heaflights and check engine light constantly comes on due to wiring problems. *ak
 Equipped w/abs brakes; four sets of brakes pads have worn excessively w/rear brake cylinders leaking. please describe details. *ak
02/25/1996
 Abs; brakes worn out so bad and there was no warning signal. at 23,000 miles had to replace pads, rotors and hub. please describe details. *ak
 Had front pads rear brake shoes, master cylinder, both valves and hoses had to be replaced. tt
05/15/1995
 Abs: brakes defective, need replacing, brake pad all way to rotor worn. tt
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - ROTOR
07/07/2003401/15/2003
 After coming to a complete stop and releasing the brake the car will go into low gear and becomes very hard to accelerate. took it to a shop because it was said to be a brake problem, i got new rotors, front and back brakes, and calipers. problem still is there.*ak
10/27/1998110/13/1998
 Brake replaced and rotors turned, causing vehicle to pull while braking *mjs
01/01/1996
 This form is not user friendly. you are precluded from going back to previous screens without losing information. i just filled out a form completely, and was cut off before i could add comments! please cross reference my information. my additonal comment is that given that my car is less than 4 years old, i feel that i have had major repair items, such as a/c compressor/ brake rotors/tie rods). if a car is made to last, these problems should not arise. the dealerships view is that a 4 year car with 27,000 miles is worn out and that's just the way it is. my other car is a saturn and after 6 years i have had zero repairs aside from normal maintenance. chrysler makes bad products, and doesn't stand behind their cars. please be on alert that there are way too many problems arising with cirrus models. i have dealt with tamiami chrysler in miami 305 266-5500 who are incompetent, liars and crooks. come down hard on chrysler. *ak
11/08/1996205/01/1995
 Brake rotors have been replaced twice.
05/25/1997106/05/1995
 Brake rotors failed due to rust.
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM
1
 Rear brakes replaced.
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM - DRUM
11/01/19962
 Master cylinder failed prior to service recall; also rear brake drums contained excessive dirt/dust, causing master cylinder to fail. *ak
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM - WHEEL CYLINDERS
09/02/2004119000412/16/2003
 Rpm's running high, transmission slipping, rough idle, abs light consistantly on even after inspection, gear slips when placing into park, while driving the car reversed on its own. have complained and wanted into another car due to having this one on a 24 lease, they denied me and have had to drive it and with 3 children and myself in the car it is not safe, but is the only transportation we have. we need help resolving this problem. *ak
05/01/1997110/05/1995
 Brake wheel cylinder failed.
08/02/1996111/24/1994
 Rear brake cylinders leak.
 Equipped w/abs brakes; four sets of brakes pads wear excessively w/rear brake cylinders leaking. please describe details. *ak
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - HOSES, LINES/PIPING, AND FITTINGS
11/18/2005611/18/2005
 Tl*the contact owns a 1995 chrysler cirrus. the contact attempted to start her vehicle, but was unsuccessful. the entire instrument panel illuminated. the vehicle was taken to a mechanic and he stated that the modulator needed to be replaced. the work was performed, but the failure recurred a month later. there is a rod on the rear driver side that is supposed to hold the wheel in place, but it has rusted. the rod fell apart and the contact had it replaced. while the vehicle was parked, she noticed that the brakeline was leaking brake fluid onto the ground. the contact took the vehicle to a mechanic and had it repaired. the vin, engine size, number of cylinders, powertrain, and failure mileage were unknown. the current mileage was 63,742.
09/10/1999
 Braking system malfunctioned, causing the brake pads to burn out, also, a fire broke out due to brake fluid leaking out from a hose and spraying onto pads. *ak
10/01/1998105/01/1995
 Many many problems with this vehicle
 Had front pads rear brake shoes, master cylinder, both valves and hoses had to be replaced. tt
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - MASTER CYLINDER
03/16/20011
 Consumer was traveling on highway and abs braking light system came on. she took vehicle to a mechanic, and he told her that master cylinder piston and hydraulic chamber malfunctioned. this vehicle wa snot included in manufacturer's recall 686. *ak *slc
 When brakes are applied vehicle will swerve. dealer inspected vehicle, and informed consumer that hydraulic control was inoperable due to corrosion. a recall 96v074000 has been issued on vehicle's make/ model; however, this vehicle was not included due to vin.*ak
06/06/2000
 Recall 96v075000/brakes:hydraulic:master cylinder: brake failed while driving at 35-40 mph, forcing vehicle into an field to avoid a collision. but, five passengers sustained minor injuries; dealer notifed. feel free to provide further details. *ak
04/13/2000210/01/1997
 Car returned to dealer for 4th time for brake failure. in the past they have not found anything wrong. now, master cylinder to be replaced for 2nd time. brake shoes and pads were replaced for second time since 10/97 in 02/00, and already show excessive and uneven wear and need replacing again. even through total brake failure, the abs warning light has never come on. this car is a nightmare!
03/05/2000301/01/1995
 Hydraulic noise under hood as brakes applied, brakes failed to stop car, caused minor crash, leaking master cyl replaced, brakes failed again twice, chrysler replacing computer module governing brake hydraulics, would not confirm this would cause brakes to fail
11/01/1995501/13/1995
 Replaced the front brake prior to the recall notice for master cylinder. yh
105/24/1995
 Master brake cylinder problems, owner has not received notice of recall, other vehicle same year and model have received notice.
209/01/1995
 Master cylinder replaced twice, still makes grinding noise.
112/16/1994
 Master cylinder failed.
07/18/19961
 Master cylinder replaced.
 After having recall repair work done, the vehicle is still having a problem with the master cylinder. recall#96v075000. *ak
11/01/19962
 Master cylinder failed prior to service recall; also rear brake drums contained excessive dirt/dust, causing master cylinder to fail. *ak
 After being stopped at a stop sign applied the accelerator and the brakes felt like they were still being applied, the vehicle began to pull to the right; replaced master cylinder. please describe in detail. *ak
06/17/19961
 Brake master cylinder failed.
 The master cylinder was replaced about four times, purchased car new . please describe .*ak
07/15/1996
 Recall 95v075, made an appointment several times to get the repair done, there are no parts available from jul. 15 to present. please describe.*ak
06/28/1996
 Failure of the brake power assist, causing the brake pedal to go to the floor, resulting in an accident.*ak
 Owner received recall notice two weeks ago, took vehicle to dealer and was told they have to order parts. dealer still does not have parts in.
11/01/1995
 Brake failure, master cylinder completly went while driving without warning. *ak
11/01/1995
 Brake failure, master cylinder completely went while driving without warning. *ak
11/09/1995101/01/1995
 The vehicle has abs brakes and while driving the system went out and would not stop the car. tt brake light came on indicating a brake problem, consumer was driving on expressway, took vehicle to dealer, and it was discovered that master cylinder had to be replaced.*jb
 Had front pads rear brake shoes, master cylinder, both valves and hoses had to be replaced. tt
SERVICE BRAKES, HYDRAULIC - PEDALS AND LINKAGES
112/20/1994
 When releasing the brake pedal, abs brakes squeal. *ak
SERVICE BRAKES, HYDRAULIC - POWER ASSIST
06/28/1996
 Failure of the brake power assist, causing the brake pedal to go to the floor, resulting in an accident.*ak
SERVICE BRAKES, HYDRAULIC - POWER ASSIST - VACUUM - HOSES, LINES/PIPING, AND FITTINGS
 Had front pads rear brake shoes, master cylinder, both valves and hoses had to be replaced. tt