Bulletins
| Bulletin | Bulletin date | Replacement Bulletin | Item no. | Summary | Added |
|---|---|---|---|---|---|
| POWER TRAIN - AUTOMATIC TRANSMISSION | |||||
| 0803006 | 08/25/2006 | 0803006A | 10021239 | Powertrain control module initialization. *kb | 03/23/2007 |
| 2100104 | 02/10/2004 | 10005978 | Transmission solenoid replacement. *tt | 04/05/2004 | |
| POWER TRAIN - AUTOMATIC TRANSMISSION - CONTROL MODULE (TCM, PCM) | |||||
| 1802907 | 04/26/2007 | 10021684 | Generic powertrain control module (pcm) procedure. *kb | 06/15/2007 | |
| 0801505 | 03/02/2005 | 10013731 | Powertrain control module initialization. *sc | 04/26/2005 | |
| 1800604A | 04/06/2004 | 1800604B | 10005981 | Generic powertrain control module (pcm) procedure. *tt *mj this bulletin supersedes bulletin 18-006-04a dated 04/06/2004. *tt | 04/05/2004 |
| 30 | 11/01/2003 | 10005354 | Powertrain control module (pcm) electrical connector seal customer satisfaction notification no. c30. *tt | 02/23/2004 | |
| 1800703C | 08/15/2003 | 1800703B | 10003541 | Generic powertrain control module (pcm) procedure. 2004 models included. *tt | 10/23/2003 |
| 03014 | 08/29/2003 | 10003520 | Service action 03014 - powertrain control module (pcm) electrical connector seal inspection/repair procedure. *tt | 10/22/2003 | |
| 1800703B | 07/25/2003 | 1800703A | 10003417 | Generic powertrain control module (pcm) procedure. 2004 models included. *tt | 10/20/2003 |
| 1800703A | 07/04/2003 | 1800703 | 10003416 | Generic powertrain control module (pcm) procedure. *tt | 10/20/2003 |
| POWER TRAIN - AXLE ASSEMBLY - AXLE SHAFT | |||||
| 0300604 | 09/15/2004 | 10010478 | Front hub/half shaft click/pop sound. *tt | 11/29/2004 | |
| POWER TRAIN - MANUAL TRANSMISSION | |||||
| 0600105 | 02/19/2005 | 10012813 | Transmission gear rattle sound at idle. *tt | 03/31/2005 | |
Consumer Complaints
| Fail date | miles | occurences | Purchase date |
|---|---|---|---|
| POWER TRAIN | |||
| 06/20/2012 | 85000 | 1 | |
| Engine light came on, it acted like it was misfiring. car shut off at around 60mph. drifted off road and restarted and went a mile or so and it shut off again we kept doing that until we got home. the next day we took it to our mechanic it ran fine on the way there, around 15 miles. he put it on his computer, it read bad injectors so he replaced them. then he took it for a ride and it acted like it was misfiring again he put it back on his computer and it read bad coil so he replaced the coil pack,plugs and plug wires. it ran fine for about 4 months . until now 10/30/2012. . took back to mechanic, he replaced o2 sensors. ran for 2wks. same thing again! once again took back to mechanic . he put it on his computer once again and it read fine. he said we should take it to our chrysler center. although we couldn't ask for a better running car (when it is running right) ,this car is very dangerous to be on the road shutting off in traffic. i would hate to have to replace it. please fine answer to problem. *tr | |||
| 06/20/2012 | 85000 | ||
| Engine light came on, it acted like it was misfiring. car shut off at around 60mph. drifted off road and restarted and went a mile or so and it shut off again we kept doing that until we got home. the next day we took it to our mechanic it ran fine on the way there, around 15 miles. he put it on his computer, it read bad injectors so he replaced them. then he took it for a ride and it acted like it was misfiring again he put it back on his computer and it read bad coil so he replaced the coil pack,plugs and plug wires. it ran fine for about 4 months . until now 10/30/2012. . took back to mechanic, he replaced o2 sensors. ran for 2wks. same thing again! once again took back to mechanic . he put it on his computer once again and it read fine. he said we should take it to our chrysler center. although we couldn't ask for a better running car (when it is running right) ,this car is very dangerous to be on the road shutting off in traffic. i would hate to have to replace it. please fine answer to problem. | |||
| 09/01/2010 | 70000 | ||
| Tl- the contact owns a 2004 chrysler pt cruiser. the contact stated the piece that goes from the gear shift to the transmission broke and the contact was unable to change gears. the contact did not remember the exact name of the part at time. the contact had the part replaced on sept. 1, 2010 and the part broke again 15 days later. the part used is made out of plastic. the dealer is replacing the part this time for free, but the contact is concerned that this may happen again while driving the vehicle and not be able to change gears. the failure mileage was 70000 and the current mileage was 70200.rl | |||
| 01/01/2005 | 59 | ||
| The consumer pt cruiser trip meter constantly reset itself, when this happens the dash lights flash on and off, gas gauge drops to empty and the bells start beeping. *bf the mechanic sprayed static guard in it that time to resolve the issue, but this did not work. the consumer was told that the problem was with the cloth seats and to get out and grab the metal bar. the gear shifter knob would come off, there was a grinding noise in the rear due to the brakes, it was hard for the consumer to get out of the vehicle at time because the lock and tumblers were sticking, the engine would knock intermittently during acceleration and would only get 12.9 miles to the gallon and would run rough intermittently, and the gauges would quit working at times. *sc | |||
| 07/21/2004 | 7027 | 3 | |
| Hose came loose from transmission causing vehicle to cut off several times. *bf *tc | |||
| POWER TRAIN - AUTOMATIC TRANSMISSION | |||
| 12/07/2009 | 121040 | 1 | |
| While driving down the freeway, my 2004 chrysler pt cruiser lost all the oil out of my engine. this caused my engine oil light immediately came on and i pulled off the freeway. after putting 2 pints of oil into the engine, i drove home only to find out that again my engine had no oil in it after roughly 50 miles of driving. i put 3 pints of oil in a day later and turned over the engine and found that my oil was leaking out of the engine gasket seal. i contacted chrysler, and the informed me that engine gasket repairs are not covered for vehicles over 120,000 miles. leaking oil in this manner is a major fire hazard, and i'm lucky that my vehicle did not catch fire while driving home. i noticed online, that many other pt owners have complained about these types of engine failures consistently. i cannot pay the 2800 dollars for this repair, the car will sit until chrysler loses this lawsuit. *tr | |||
| 05/22/2009 | 36000 | 1 | |
| This vehicle i purchased new with 236 mi. at 36000 miles the transmission has started to lunge forward upon starting of the vehicle and also at a stop it lunges and acts like the engine is going to quit . is it going to take a fatality of a pedestrian or other motorists before this issue is addressed? this is consistently the way this vehicle runs. *tr | |||
| 07/20/2008 | 17901 | 1 | |
| Vehicle lunges forward when coming to a stop and stalls when accelerating. you have to keep your foot firmly on the brake when stopping to prevent the sudden forward motion and be careful when pulling out into traffic because of the stall. this problem has been ongoing since purchasing the car in july 2008 with only 17,900 miles on the car. it is now march 2009 and the car has around 29,000 miles on it, with the same problems. the problems are not getting worse. *tr | |||
| 09/10/2004 | 500 | 100 | 02/01/2004 |
| 2004 pt cruiser stalls when stopping without warning. stalls when turning corners or stopping for signs and traffic lights. accidents almost occurred a number of time. 2 separate dealers have had the car, they cannot make it do it? at least 10 trips and the last 9 without paperwork because they say they don't need it until they check it out. something is fishy with these cars. private party looked at the problem and said the transmission is not down shifting when coming to a stop or slowing to minimum speed. dealers and chrysler are denying a problem. i am getting rid of the auto as it is too unsafe to continue driving. i hope more owners of these complain as to get something done asap. someone is going to get killed. *jb | |||
| 05/28/2005 | 5493 | 1 | 07/20/2004 |
| Dt: consumer states that the dealer's service department is telling her that the transmission is not going into fourth gear. 11/2004, 5/5/2005, 5/6/2005, 2/25/2005 she had the vehicle serviced. the light on the dash board came on so she took vehicle in, got the car back and the light came back on. consumer took the vehicle back in last wednesday and vehicle has been there ever since. consumer feels the vehicle is too new to have this many problems. *tt | |||
| POWER TRAIN - AXLE ASSEMBLY | |||
| 05/06/2007 | 52437 | 3 | 08/01/2005 |
| Starting in the fall of 2006 when making a left turn it made a grinding, squealing noise. it was very loud. thought it needed brakes, and had it checked . they were fine. then, it felt like the tire was bad on the passenger's front. took the car to dealer in mid march 2007 to have the tire checked and it was a loose axle instead. that stopped the squealing for the time being. just recently we thought the rotors needed turned because the vibrations and noises had started again. on 5-06-07 my son was killed when he went off the right side of the road and supposedly overcorrected and rolled several times. after further investigation into the crash it was discovered that half of the front passenger rotor broke off with a bubble defect in the metal. there appeared to be an old crack across the rotor along with the brake that severed it. not sure what was going on, but there' was obviously a problem with the front ends and if it saved a life it was worth checking into. *ak | |||
| 06/05/2006 | 1 | 11/25/2004 | |
| I have had to replace the front wheel assembly twice in less than a year. purchased new wheel bearings and the entire hub assembly and even a whole new axle. have continued to have problems. was told by mechanic that the axle is too short and is coming loose resulting on the expedited wear on the bearings causing a need for a whole new assembly. i am extremely frustrated with this vehicle. *nm | |||
| 02/07/2005 | 1 | ||
| While driving approximately 35 mph front axle literally broke. there were no injuries.*ak | |||
| POWER TRAIN - CLUTCH ASSEMBLY | |||
| 03/26/2005 | 17000 | 1 | 06/27/2004 |
| When shifting from first to second gear vehicle stopped moving and would not shift into gear. vehicle was towed to the dealer, who informed consumer hat the clutch and bearing needed to be replaced. consumer was concerned that the parts wore out with less then 17,500 miles.*ak | |||
| POWER TRAIN - DRIVELINE | |||
| 01/02/2011 | 35508 | ||
| Front wheel bearings worn ,extremely clearance(wheel moves approximateil 1 inch top to bottom when shaking it). will replace bearings soon. noticed while replacing front brakes at 35,508 miles. a sealed wheel bearing should not wear out at this low mileage unless defectt in bearing or manufactures design. | |||
| 07/14/2006 | 17000 | 1 | 11/01/2005 |
| Pt cruiser. vibration at certain speeds while under acceleration. *jb | |||
| POWER TRAIN - MANUAL TRANSMISSION | |||
| 07/28/2006 | 24000 | 3 | 01/10/2004 |
| I have owned a manual shift 2004 chrysler pt cruiser since jan 2004. in june of 2006 the vehicle started rolling back in our driveway. it does not matter what gear it is in. i reported this to the dealer who at first said it wouldn't happen. then they saw it with their own eyes. they diagnosed the problem and said it was the clutch slipping. two days later i had paid for a new clutch and was told the vehicle did not roll back anymore, even when they pushed on it. i was told to set the parking brake at least 3 clicks for the next 3 days until the clutch had settled in. three weeks later i parked on my drive of normal slope and ran inside for 5 minutes. when i returned the vehicle was 3/4 down the driveway. i returned the vehicle to the dealer. the next day they called to tell me that their service manager and mechanic had been told by chrysler that the roll back is normal for that car. when asked why it never did it before i was told that the engine had gotten older and more lose and that all the pt cruisers roll back. i have been working with the dealer who has been in touch with chrysler. i have also reported this problem with the customer assistance center but they are still standing their ground saying that the roll back is normal. now the dealership is saying even a 2006 manual shift pt cruiser can be seen rolling back when they put it on a slope in their shop. i believe this is a major safety issue. it could actually cause a death if there was a child playing near the vehicle or even injury to an adult. *jb | |||
| POWER TRAIN - MANUAL TRANSMISSION - FLOOR SHIFT ASSEMBLY | |||
| 03/26/2005 | 17000 | 1 | 06/27/2004 |
| When shifting from first to second gear vehicle stopped moving and would not shift into gear. vehicle was towed to the dealer, who informed consumer hat the clutch and bearing needed to be replaced. consumer was concerned that the parts wore out with less then 17,500 miles.*ak | |||
| POWER TRAIN - MANUAL TRANSMISSION - LUBRICANT | |||
| 03/01/2007 | 30000 | 1 | 09/15/2004 |
| After my 30,000 mile major maintenance, i noticed a leak on the the driver side front of the car. i took it back to the dealer and they said it was a transmission oil leak. it was under the $100 deductible warranty so i paid the $100 and they fixed it. the leak continued after 3 other attempts to fix it over a 6 month period. it is currently in the dealer shop to be fixed and they say they can't find the leak. they now think it's coming from the top. since i don't monitor the transmission fluid level, my concern is that i will have a major failure the may cause an accident and/or injury if the transmission fails. also, the car is kept in my garage during extended times when i'm out of town and there is a considerable puddle when i return. i'm assuming that the transmission oil is flammable so there is some concern there. the dealer has been cooperative but seems to lack guidance and how to fix it. *tr | |||