Cobra Cobra 1987-2003
Model Cobra made by Cobra got 13 consumer complains. Consumer complaints with reference, among others things, to electrical system, engine and engine cooling and fuel system, gasoline.
Car model
| Name | Recalls | Bulletins | Investigations | Consumer Complaints |
|---|---|---|---|---|
| Cobra Cobra 1987 | 0 | 0 | 0 | 1 |
| Cobra Cobra 1989 | 0 | 0 | 0 | 1 |
| Cobra Cobra 1990 | 0 | 0 | 0 | 4 |
| Cobra Cobra 1991 | 0 | 0 | 0 | 1 |
| Cobra Cobra 1992 | 1 | 0 | 1 | 2 |
| Cobra Cobra 1993 | 1 | 0 | 1 | 0 |
| Cobra Cobra 1994 | 0 | 0 | 1 | 1 |
| Cobra Cobra 1995 | 0 | 0 | 1 | 0 |
| Cobra Cobra 1996 | 0 | 0 | 0 | 5 |
| Cobra Cobra 1997 | 0 | 1 | 0 | 0 |
| Cobra Cobra 1998 | 0 | 1 | 0 | 0 |
| Cobra Cobra 2003 | 0 | 0 | 0 | 2 |
Model 9999
Consumer Complaints
| Fail date | miles | occurences | Purchase date |
|---|---|---|---|
| ELECTRICAL SYSTEM - WIRING | |||
| 1 | |||
| (the name listed above is the attorney of the consumer: mr. mcchesney) and he experienced numerous problems with the vehicle. and one of the problem(s) are as followed: the wiring was installed in a manner that would cause shorts and electrical fires. *scc | |||
| ENGINE AND ENGINE COOLING - ENGINE | |||
| 7 | |||
| (the name listed above is the attorney of the consumer: mr. mcchesney) and he experienced numerous problems with the vehicle. and one of the problem(s) are as followed: there is water in the oil system & the lower end of the engine leaked oil, the bore of the blocks are oversized (at .030-the max you can bore this block), there are score marks at the bottom of all bores, the pistons are loose in the bores-the block must be replaced, the rocker arms cannot lash the valves to proper settings, the engine over heated on several occasions/at slow speeds and caused the gaskets to blow, and the blown gaskets caused the water to leak into the oil system, damaging the rings and the engine bearings. also the cylinder heads were assembled with the lock washers on the head bolts, causing failure of the head gaskets when they broke, and the rear main seal was leaking along with the oil pan assembly. (upon the removal of the rear main cap, found that the main bearings are .010/oversized) *scc *dt | |||
| FUEL SYSTEM, GASOLINE - CARBURETOR SYSTEM | |||
| 1 | |||
| (the name listed above is the attorney of the consumer: mr. mcchesney) and he experienced numerous problems with the vehicle. and one of the problem(s) are as followed: the threads are stripped in several locations of the intake manifold. *scc | |||
| FUEL SYSTEM, GASOLINE - STORAGE - TANK ASSEMBLY | |||
| 2 | |||
| (the name listed above is the attorney of the consumer: mr. mcchesney) and he experienced numerous problems with the vehicle. and one of the problem(s) are as followed: the fuel tank was leaking in several areas, and upon the removal of the fuel tank, it was found that the construction standards were dangerous and a fire hazard. *scc | |||
| OTHER | |||
| 1 | |||
| Possible safety issue with the seat installation of replica race cars.*mr other problems with the vehicle which included: manufacturer seat rails to replace incorrectly installed seats bolted to the floor with ten washers. bleed air out the oil pressure gauge line to correct inaccurate gauge readings. installed rear spring coil spacers to reduce travel when going over bumps. replaced water temperature gauge. all orange-peel in the paint was machine buffed. the hood was removed and buffed to reduce the bump and reinstalled. the passenger door was realigned to correct the rubbing against the front body panel. *ph *jb | |||
| POWER TRAIN - DRIVELINE - DRIVESHAFT | |||
| 2 | |||
| (the name listed above is the attorney of the consumer: mr. mcchesney) and he experienced numerous problems with the vehicle. and one of the problem(s) are as followed: upon the removal of the transmission clutch, the bell housing and fly wheel, the drive shaft was misaligned by a margin which will require the modification of the existing mounting of the transmission differential, and the clutch assembly was worn to the point that the drive disk needs replacement. *scc | |||
| SEATS | |||
| 1 | |||
| Possible safety issue with the seat installation of replica race cars.*mr other problems with the vehicle which included: manufacturer seat rails to replace incorrectly installed seats bolted to the floor with ten washers. bleed air out the oil pressure gauge line to correct inaccurate gauge readings. installed rear spring coil spacers to reduce travel when going over bumps. replaced water temperature gauge. all orange-peel in the paint was machine buffed. the hood was removed and buffed to reduce the bump and reinstalled. the passenger door was realigned to correct the rubbing against the front body panel. *ph *jb | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - MASTER CYLINDER | |||
| 1 | |||
| (the name listed above is the attorney of the consumer: mr. mcchesney) and he experienced numerous problems with the vehicle. and one of the problem(s) are as followed: the cylinder heads were assembled with lock washers on the head bolts, causing failure of the head gaskets when they broke. *scc | |||
| STEERING - LINKAGES - ROD - RELAY - CONNECTING | |||
| 1 | |||
| (the name listed above is the attorney of the consumer: mr. mcchesney) and he experienced numerous problems with the vehicle. and one of the problem(s) are as followed: the push rods are not long enough. *scc | |||
| STRUCTURE | |||
| 1 | |||
| Possible safety issue with the seat installation of replica race cars.*mr other problems with the vehicle which included: manufacturer seat rails to replace incorrectly installed seats bolted to the floor with ten washers. bleed air out the oil pressure gauge line to correct inaccurate gauge readings. installed rear spring coil spacers to reduce travel when going over bumps. replaced water temperature gauge. all orange-peel in the paint was machine buffed. the hood was removed and buffed to reduce the bump and reinstalled. the passenger door was realigned to correct the rubbing against the front body panel. *ph *jb | |||
| SUSPENSION - REAR - AXLE - NON-POWERED AXLE ASSEMBLY | |||
| 1 | |||
| (the name listed above is the attorney of the consumer: mr. mcchesney) and he experienced numerous problems with the vehicle. and one of the problem(s) are as followed: the front-end alignment was not correct, and the rear stub axles rub the frame. *scc | |||
| SUSPENSION - REAR - SPRINGS - COIL SPRINGS | |||
| 1 | |||
| Possible safety issue with the seat installation of replica race cars.*mr other problems with the vehicle which included: manufacturer seat rails to replace incorrectly installed seats bolted to the floor with ten washers. bleed air out the oil pressure gauge line to correct inaccurate gauge readings. installed rear spring coil spacers to reduce travel when going over bumps. replaced water temperature gauge. all orange-peel in the paint was machine buffed. the hood was removed and buffed to reduce the bump and reinstalled. the passenger door was realigned to correct the rubbing against the front body panel. *ph *jb | |||
| TRAILER HITCHES | |||
| 05/13/1995 | 3 | ||
| Recall repairs (93v054) to reflective devices and associated equipment refused by dealer due to part unavailability. *skd | |||
Car dealers selling
| State | City | Zip | Name | Phone |
|---|---|---|---|---|
| AZ | TEMPE | 85281 | LEVY RACING INC. | 480-446-8442 |