Recalls


CampaignManufacturerManufacturing dateType# of units affectedDate Owner notified MfgRecall Initiated byManufacturers of recalled vehicles/productsReport Recieved DateRecord Creation DateRegulation Part NumberFMVSS Number
SERVICE BRAKES, HYDRAULIC - POWER ASSIST - VACUUM - HOSES, LINES/PIPING, AND FITTINGS
97V068000CHRYSLER CORPORATIONfrom 06/25/1995 to 06/25/1996V (Vehicle)5800005/19/1997MFRCHRYSLER GROUP LLC04/28/199705/01/1997
Defect SummaryVehicle description: pickup trucks equipped with diesel engines. the engine driven vacuum pump can allow engine oil into the vacuum hoses due to the absence of an internal check valve. the oil can cause the hose to deteriorate and partially collapse, reducing the vacuum supply to the brake booster.
Consequence SummaryReduced power brake assist can result increasing the risk of a vehicle crash.
Corrective SummaryDealers will add a vacuum pump check valve to the vacuum pump. in addition, the vacuum hose connected to the vacuum pump will be replaced with a hose that is engine oil resistant.
NotesOwner notification began may 19, 1997. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chrysler at 1-800-853-1403.also contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393.

Bulletins


BulletinBulletin dateReplacement BulletinItem no.SummaryAdded
SERVICE BRAKES, AIR - DRUM - SHOES/LININGS
05049703/28/199754386Front brake lining wear prematurely when compared to the wear experienced on the rear brake linings. *yc04/07/1998
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS
05069906/25/1999606161Information regarding accelerated brake lining wear, front versus rear. *tt08/11/1999
05039703/17/199751965Brakes - chassis dynamics diagnosis. *tw07/17/1997
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM - SHOES/LININGS
05059703/28/199705-02-96A6088765Concerns with accelerated brake lining wear, front versus rear. *nlm01/07/2000
SERVICE BRAKES, HYDRAULIC - POWER ASSIST - VACUUM
05119912/31/1999609987Information regarding a revised power brake booster check valve. *tt04/12/2000

Investigations


NHTSA IDManufacturerDate openDate closeSubjectRecall campaign
SERVICE BRAKES, HYDRAULIC
EA98005CHRYSLER GROUP LLC02/27/199805/24/1999CLUTCH HYDRAULIC LINE
 Alleged plastic clutch tube may fail from exposure to exhaust heat, resulting in loss of clutch function and possible vehicle fire.
PE97043CHRYSLER GROUP LLC10/20/199702/27/1998CLUTCH HYDRAULIC LINE FAILURE99V115000
 Alleged clutch line may melt and leak hydraulic fluid in the vicinity of the exhaust manifold.leaked hydraulic fluid could ignite and cause a vehicle fire.

Consumer Complaints


Fail datemilesoccurencesPurchase date
SERVICE BRAKES, AIR - ANTILOCK
01/05/1999305/01/1997
 On three occasions brakes have lost pressure to hydraulic system. on last incident accident was the result of losing braking entirely. since system totally failed and inspection of braking components,excluding abs, have not uncovered defect it,but light on abs system has turned on -indicating system problem - i believe abs components may be faulty
08/07/1996
 When backing the truck there were no brakes when going forward, vehicle has abs anti-lock brakes . please descibe.*ak
 When applying the brakes in damp weather, the front brakes lock up, causing the vehicle to slide.*ak
SERVICE BRAKES, HYDRAULIC
05/21/19973
 Consumer has a problem with brakes. they work fine when driving in town. when driving at 30 - 35 mph or more, the brakes do not stop accurately. when pressing the pedal for braking driver must release them. then press again before stopping. *ak
08/31/19961
 Going to a camp ground on dirt road, hauling a trailer, going down a hill, driver tried to apply brakes (abs), had no brakes, ran into another vehicle w/trailer, the other vehicle literally stopped the vehicle at bottom of hill.*ak after inspection, it was found that the master cylinder was faulty. *slc
SERVICE BRAKES, HYDRAULIC - ANTILOCK
1
 The abs and the brake light illuminated. the vehicle brakes even when not in motion. the service writer says consumers vehicle needs a cabs computer module. the front rotors needed replacing because of what the dealer claims to be pitting. a friend in formed consumer that it was because of air bubbles in the casting when the rotors were made. *jg
01/14/20020
 Abs light came on and had not turned off. had taken vehicle to dealer, they fixed the problem for a couple days. but, problem came back. please provide more information.*ak
01/14/20020
 While driving could step on the brake pedal to reduce or to stop vehicle. pedal will pulse causing extended stopping distance, dealer had been contacted. please provide more information.*ak
08/21/20011
 The front and rear causing the abs and brake light to illuminate while driving. nlm
04/01/1996
 During application of brake system vehicle will suddenly pull hard to left or right, direction is unpredictable. dealership has examined vehicle, but was unable to remedy problem. please provide any additional information / attachments. *ak
11/01/20000
 Abs braking system light comes on dashboard and stays on. dealership is aware of problem.*ak
05/20/2001
 When applying brakes in a panic stop they locked up, resulting in a collision which caused minor injuries. *ak
10/01/20000
 When applying brakes abs braking system lights comes on dashboard panel. dealership is aware of problem. pedal is hard and sticks a little.*ak
10/10/20000
 Consumer was traveling on highway the and noticed that abs braking system light came on intermittently on dashboard. dealership was aware of problem.*ak
08/07/20000
 While driving to a stop sign behind other vehicle, applied brake pedal and vehicle lost braking power. consumer was forced to drive off the road. technician pointed out that problem was with brake line that delivered fluid to brakes. *ak
06/01/1996
 When applying brakes vehicle will pulls hard to left . dealer has resurfaced front brakes, and flushed master cylinder and its lines, but defect keeps reoccurring. *ak
12/01/1995
 Transmission will not shift to 2-3 geras normaly, also, abs brake light comes on at idle. *ak
 When applying the brakes the pedal goes to the floor, causing extended stopping distance. replaced brakes five times within two years. also, the rotors are prematurley wearing. please give any further details. *ak
08/15/1998410/02/1997
 Transmission shudders at 45 mph, does not shift and shakes when going into 3rd or overdirve, and jerks and slips, dealer has replaced the valve body and reconditioned transmission and replaced convertor, transmission continues to lock up and jerk. driver and passenger side mirrors were both replaced due to being loose. emergency brake handle came off and was replaced. fuel gauge read empty with 12 gallons in tank, dealer replaced fuel pump module. wiper blades weren't cleaning windshield, dealer replaced both wiper blades, windshield washer was inoperable, dealer replaced washer motor. vehicle has experienced many problems with the interior and dome lights failing, dome light keeps blowing fuse and dealer has replaced the strip lighting and fuse box door and repaired the open circuit to junction block. radiator cap was replaced due to low coolant. there was a brake fluid leak, dealer replaced caps for the master cylinder, the brake and abs light were illuminated, dealer replaced rear wheel speed sensor and wiring. passenger side vent window would not open and leaked air. vehicle only gets 13mph on highway, consumer states this is poor gas mileage. *slc
03/24/1999105/01/1997
 When applying the brakes, vehicle has no power. also, the power steering failed, causing consumer to put vehicle into neutral, and rev the engine. took six months to get part after repeated calls. front brakes wearing out prematurely because rear brakes are not self adjusting. very unsafe when braking at higher speeds. *yc the left rear axle seal was leaking. water collects near the passenger door underneath the carpet. *yh
 Abs brake problems; when applying brakes duriing heavy braking conditions, abs brakes do not work correctly, and truck glides along. this happens on normal road condtions. the dealer is not able to detect what the problem is with the system. please provide further details. *ak
11/05/1998509/01/1995
 Excessive pedal effort required to stop vehicle in normal braking situations. front brakes smoke during hard stops or in stop and go traffic. it also gives off a burning smell. brought back to dealer 2 times and they state that it is normal. i just found out that in 1997, dodge changed the master cylinder on this truck to a larger unit. the rest of the brake system components are the same. i would think that this would solve my problem. *ak
08/09/1998506/24/1996
 The brakes were replaced at least 5 different times. brake lining overheats when brakes are applied. vehicle not stopping when brakes are applied quickly. dealer cannot find problem. *ak *ml
311/17/1995
 Brakes have been a continued problem with vehicle, several repairs made however continue to have problems.
 Abs brakes; when applying brakes in a panic stop, the brakes fail to stop the vehicle, causing extended stopping distance. please provide details. *ak
 When driving at various speed and applying brakes, vehicle pulls to the left. the harder pushes on brakes the harder vehicle pulls to left. consumer has to counter steer in order to avoid hitting oncoming traffic. has replaced brakes pads, but defect is still occurring. *ak
 Abs brakes; when applying brakes in a panic stop, there is extended stopping distance before vehicle comes to a complete stop. please describe details. *ak
 While driving on icy roads abs brakes lock up.
05/01/1996107/31/1996
 Abs brakes failed.
08/08/1997
 Abs brake problems; intermittently when applying the brakes on dry road conditions, under normal braking, they seem to be very spongy, and the pedal travels to the floorboard. they do not stop the truck. all brake pads have be replaced on 3/7/98. the rear brakes pads were glazed over like they were heated up. *ak
01/10/1998
 While driving the truck applied the brakes and the abs brakes failed. on 4-3-98, driver applied the brakes and the entire brake system went out, leaving the driver with no brakes. owner has taken the truck into dealer three times, and they replaced numerous parts, such as the fuel pump, spark plug wire, and etc. the truck still is having brake problems. *ak
06/01/1997
 Abs system malfunctioned due to a module which has been replaced less than a year. the abs and braking light comes on. during a panic stop the wheels lock up. dealer cannot determine problem. *ak
11/01/1996
 Front brakes pull really hard to left and to right.
01/08/1997412/10/1996
 Anti-lock brakes grab.
12/26/1996103/01/1996
 Anti lock brakes lock up, causing loss of control.
02/27/1996200
 Turned engine on, no reserve load. pumped brakes 4-6 times. let sit 1-3 minutes, no back support and vacuum assist disappeared. dilemma: total loss of braking capability. *ak
10/20/19974
 When applying the abs brakes the pedal will intermttently travel to the floor, causing extended stopping distance which nearly caused a collision. also, dealer replaced calipers/rotors and master cylinder. *ak
0
 Recall 97v068000; 2 weeks ago the recall work had been performed at auto west dodge. now, if the brakes are hit more than six times, the brakes will fail. *ak
05/01/1997
 Abs equipped: upon depressing the brake pedal consumer noticed the front end shimmy. pedal traveled to the floorboard, resulting in extended stopping distance. consumer, therefore, released foot from brake pedal to gain control of vehicle. consumer has contacted the dealer. please provide any further details. *ak
10/21/1997
 While driving at 20 mph the defective abs braking system malfunctioned causing the wheels to lock up and skid. having extended stopping distance, causing a frontal impact. the defective driver's side airbag did not deploy. *ak
10/17/19963
 While driving on freeway, consumer applied brakes & vehicle pulled left, across 2 lanes. at a much lower speed, pulled right. took to dealer several times for brake problem & was corrected 75%. was informed normal for truck to pull right. *ak consumer states that the vehicle is now constantly pulling to the left at any speed. *slc
104/06/1996
 Rear anti lock brakes failed.
06/18/19974
 When brakes are applied vehicle veers to the right; also, abs light and brake lights come on when pulling a trailer. in addition, replaced front brake rotors/pads/calipers. *ak
01/01/19961
 On any type of road surface, when braking in an emergency situation, the brake pedal goes to the floor and the vehicle does not stop. condition almost caused several crashes. *ak front brake pads was replaced at 40,000 miles. problem still exist. *jb
07/06/1996206/25/1996
 While trying to stop vehicle and putting on brakes the vehicle wll pull hard in any direction, causing driver to go off the road. *ak brakes have been replaceed on 4 occasions, however problem still persisted, chrysler is replacing vehicle. *slc
03/13/199614
 When applying abs brakes vehicle shakes violently/pulls to the left. *ak
04/29/1997206/26/1996
 Vehicle experienced a transmission overheating problem. also, vehicle pulled to the left upon braking/front end misalignment pulled vehicle to the right. *ak
04/14/1997
 Abs brake failure, when brakes are applied vehicle pulls to the right, and when coming to a stop, brakes lock up/jerks the vehicle, causing a loss of control. *ak
04/17/1997
 Abs brake failure, made a loud noise , also, replaced disc pads/rotoes and calipers. *ak
10/16/1996
 While driving the brakes would pull and vibrate. also, the brakes made a loud noise without applying the brakes. dealer replaced brakes every 6000 miles. *ak
01/29/1997206/07/1996
 Abs brakes failed, applied the brakes and the pedal goes the floor, loss of effectiveness, pedal fade,s. in for replacement of master cylinder, bleeding the lines. *ak
03/17/1997204/01/1996
 When applying the brakes on normal road condtions the pedal went to the floor and vehcile hit a curb. the system has abs. *ak
05/23/19964
 When braking pedal sometimes goes to floor, vehicle pulls to left, no accidents. dealer aligned wheels, replaced shim pack, various speed. *ak
09/23/1996103/28/1996
 Antilock brakes failed.
05/11/1996102/17/1996
 Antilock brakes inoperative.
12/10/1996
 Abs brakes make vehicle pull to side as a result of of recent repairs. *ak
 Owner has abs brakes, she states that the pedal goes to the floor when brakes are applied and that there is noticeable pedal fading when brakes are used. *ak
09/16/19963
 Anti-lock brakes defective; when applied, truck spins around, according to dealer, abs do not seem to be working, hard to stop, lock up on wet pavement, no accidents, speed from 30 to 45 mph. *ak
 Equipped w/rear abs brakes; front disc brakes wear excessively with replacements of three sets of pads. front rotors and calipers have also been replaced with failure reoccurring repeatedly. *ak
04/23/19961
 When driving the abs brake light comes on the dashboard and the brake pedal gets soft and goes to the floor. *ak *jb
09/05/1996
 Consumer states that when applying the brakes they lock up and throw vehicle off the road. the vehicle will slide more on on wet roads. the system has abs. has been experiencing problem since owning the vehicle. *ak
101/01/1996
 When appying the abs brakes, the vehicle pulls to the right and left sides. *ak consumr states at 12,000 miles there was extensive brake pad wear on front brakes, consumer contacted manufacturer and was advised they were aware of the braking problems.*jb
04/04/1996
 When driving in the rain at 30 mph you have to apply so much brake pedal that the front abs brakes lock up; also, the brake pads have been replaced at 5,500 and 18,000 miles and the calipers have been rebuilt at 18,000 miles. *ak
 In ten months the front rotor and pads wore out, vehicle has abs anti-lock brakes. please describe . *ak
10/18/1996
 On wet road conditions when applying the brakes, the brake pedal went to the floor and there was no braking ability. the system has abs. *ak
02/02/1996
 When hitting the brakes hard the brakes grab and release and have no braking ability. they do not hold. this happens on normal road conditions the system has abs. *ak
01/11/1996
 Poor abs brake performance, complete brake failure has been experienced 8 times, the whole vacuum system has been replaced. the pedal goes to the floor. the brake warning lights did come on. dodge ram br2500 diesel 1996. *ak
04/04/1996
 Abs brakes have been replaced 3 times; at 4/96-5,000 miles/ 7/96-10,000 and 9/96 14,000. brakes have to be replaced again at 18,000. *ak
10/12/1996
 Consumer was rearended and the driver's side air bag didn't deploy, also the seat belt didn't restrain and abs skidded and went to one side . please describe . *ak
 Abs brakes failed when trying to stop at light, applied emergency brakes when coming to a bumpy stop, hit car in rear, causing minor damage.*ak
 When applying the brakes, the abs brakes failed. please describe. *ak
208/05/1995
 Abs brakes failed with brake pedal going to the floor, also 3rd sideview mirror blurs vission. *ak
04/07/19961
 During frontal impact, the driver's side air bag did not deploy, also abs brakes failed. *ak
11/30/1995
 Abs/rear wheel: when coming to a stop, braking takes extremely long time to stop, driver literally has to stand on brake pedal to stop, caused accident, vehicle ran into light post.*ak
08/31/19961
 Going to a camp ground on dirt road, hauling a trailer, going down a hill, driver tried to apply brakes (abs), had no brakes, ran into another vehicle w/trailer, the other vehicle literally stopped the vehicle at bottom of hill.*ak after inspection, it was found that the master cylinder was faulty. *slc
07/18/199607/04/1996
 Failure of the abs brakes, causing loss of power assist, the brake pedal went to the floor.*ak
08/13/1996
 During vehicle operation. when the abs brakes are applied, a severe pull to the right is experienced.*ak
06/19/199605/28/1996
 Abs; went to apply the brakes and pedal went to the floor. lost all braking power, also replaced leaking master cylinder/booster . *ak
08/07/1996
 When backing the truck there were no brakes when going forward, vehicle has abs anti-lock brakes . please descibe.*ak
04/09/1996
 Abs: anti-lock brakes/normal brake light on dashboard remains illuminated;reset when engine is off, comes back on upon startup, causing abs to fail. *ak
05/01/199605/11/1996
 Abs, brakes make a loud noise when coming to a stop, vehicle will jump when coming to a stop, also replaced front brake pads/ windshield wipr blade/rearview mirror. *ak
03/12/1996
 Failure on the front disc brakes, need to replace the front brakes and pads and shoes to often. *ak
06/13/1996
 Abs braking system failed to stop vehicle when coming off exit. when applying brakes vehicle steered to the left. almost caused an ident. please describe. *ak
06/20/1996
 Abs; ran into the back of a vehicle because brakes would not stop the truck. please describe details. *ak
03/18/1996103/16/1996
 Epa standard. onboard computer redesigned for 1999, doesn't provide proper reading to engine, resulting in hesitation and stalling. *ak
06/18/1996
 Ask for ext 455. backing out of driveway something popped, noticed light on dash panel. loss total brake and anti lock braking system. *ak
 W/all around abs brakes; performance when applied results in excessive pulling in either direction w/cause unknown. pads, rotors and calipers replaced. *ak
 Abs braking system not working properly, experiencing weak/mushy brake pedal. *ak
05/17/1996
 The abs system will not stop the vehicle at all. please describe. *ak
05/19/1996
 Abs brake system locked up on wet surface. *ak
 While backing up made attempt to slow/stop, brake pedal went to floor at approx. 10mph, afterwards abs and hydralic light appeared.
 Abs braking system not working properly, experiencing weak/mushie brake pedal. *ak
 Abs braking system not working properly, experiencing weak/mushy brake pedal *ak
03/07/1996
 Abs brakes; failure on the abs brakes, the brake pedal went to the floor, causing the consumer to have a accident. *ak
11/15/1995
 Abs: lot of pulsation when applying; steering pulls left/right on hard brake application. *ak
01/14/1996
 Failure of the abs brake caused consumer to have a near accident. tt
SERVICE BRAKES, HYDRAULIC - ANTILOCK - ABS WARNING LIGHT
06/29/1996102/17/1996
 Antilock brake warning light illuminated.
11/12/1996111/04/1995
 Other: airbag warning light/antilock brake warning light illuminated.
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS
1
 The abs and the brake light illuminated. the vehicle brakes even when not in motion. the service writer says consumers vehicle needs a cabs computer module. the front rotors needed replacing because of what the dealer claims to be pitting. a friend in formed consumer that it was because of air bubbles in the casting when the rotors were made. *jg
 When driving downhilee brakes will not stop vehicle. consumer also stated vehicle has inadquate braking, burns up calipers and brake pads. dealer contacted. nlm
11/01/2001
 Brakes are not working properly, causing extended stopping distance. please provide more information. *ak
05/02/1996105/01/1996
 Consumer states the vehicle keeps blowing wheel seals which contaminate the brakes, consumer purchased lifetime wheel seals and lasted two weeks.*ak. consumer also stated the throttle linkage has been replaced 3 times.*slc
08/19/1999
 When the brakes are applied the pedal gets mushy and goes to the floor causing extended stopping distances resulting in a collision. the dealer has notified. mjs
08/15/1998410/02/1997
 Transmission shudders at 45 mph, does not shift and shakes when going into 3rd or overdirve, and jerks and slips, dealer has replaced the valve body and reconditioned transmission and replaced convertor, transmission continues to lock up and jerk. driver and passenger side mirrors were both replaced due to being loose. emergency brake handle came off and was replaced. fuel gauge read empty with 12 gallons in tank, dealer replaced fuel pump module. wiper blades weren't cleaning windshield, dealer replaced both wiper blades, windshield washer was inoperable, dealer replaced washer motor. vehicle has experienced many problems with the interior and dome lights failing, dome light keeps blowing fuse and dealer has replaced the strip lighting and fuse box door and repaired the open circuit to junction block. radiator cap was replaced due to low coolant. there was a brake fluid leak, dealer replaced caps for the master cylinder, the brake and abs light were illuminated, dealer replaced rear wheel speed sensor and wiring. passenger side vent window would not open and leaked air. vehicle only gets 13mph on highway, consumer states this is poor gas mileage. *slc
09/08/1997410/01/1995
 Brake performance diminished, takes heavy brake pedal pressure to stop. parking brake does not hold vehicle, with parking brake pushed on hard the vehicle can still creep. front brake pads wearing very qucikly, rear brake shoes glazed. rear brake shoes replaced three times, a new set of heavy duty rear wheel cylinders were installed by the dealer. the wheel cylinders helped some but the truck has poor braking performance, especially with a light load in the bed or towing an empty 16' flat bed trailer. replaced front brake pads and they were worn unevenly. i don't know if a proportining valve would cause this kind of problem. the dealer has tried what they thought would fix the problem. the truck is out of warranty now since october of 1999.
05/21/1999205/28/1996
 While driving vehicle suddenly accelerated, causing a crash. sudden acceleration problem happened once before. dealer could not determine the problem. *ak brake failed. *yd
3
 Braking system fails intermittently.
10/07/19961
 Brakes failed.
107/16/1996
 Brake system has never worked properly.
09/01/1996
 While applying the brakes the vehicle will move to the right lane unexpectedly. has to release the brakes in order to move back into the orginal lane, which may cause an accident. dealer cannot determine problem. dealer replace control arms, brake pads etc. please provide details. *ak
05/21/19973
 Consumer has a problem with brakes. they work fine when driving in town. when driving at 30 - 35 mph or more, the brakes do not stop accurately. when pressing the pedal for braking driver must release them. then press again before stopping. *ak
11/07/19961
 Brakes continue to pull hard, several repairs made however have failed to remedy situation.
09/03/1997
 Received recall notice (#97v06800) & called dealer for an appointment. was informed that they had no parts. called back 3 weeks later & informed of the same thing again. parts on back order. *ak
01/01/1996112/01/1995
 Brakes failed.
07/06/1996206/25/1996
 While trying to stop vehicle and putting on brakes the vehicle wll pull hard in any direction, causing driver to go off the road. *ak brakes have been replaceed on 4 occasions, however problem still persisted, chrysler is replacing vehicle. *slc
07/12/1997
 When applying the brakes the vehicle keeps on going for a short distance before the vehicle comes to a stop. driver noticed that the vehicle has a lot of vibration and shaking in it. *ak
5
 Brakes failed 5 times.
02/12/1997102/01/1996
 Brake noise.
06/12/1996
 When applying the brakes the vehicle pulls to the left. dealer attempted to fix vehicle several times but the vehicle stills pulls when applying the brakes. *ak
01/13/1996101/13/1996
 Brake problem causes vehicle to pull to the left when brakes are applied.
10/02/1996110/01/1995
 When driving at any speed applied brakes and they made a loud grinding noise, in for repair twice in one year. *ak
06/14/1996
 When applying the brakes, the right front brake locked up. please describe.*ak
07/15/1996111/01/1995
 Brake rotors/pads/master cylinder replaced due to brake failure/pulling to one side.
07/31/1996
 Applied brakes, front brakes completely disintegrated, driver heard loud noise, noticed loss of stopping power prior to failure, no other prior warning. drove very slowly until came to stop, no accident.*ak
03/12/1996
 Vehicle brakes are pulling to the right when applying the brakes. *ak
 Not sure if abs or not; when applying brakes, they stick, grinds/vibrate and eventually shuts engine off. please describe details. *ak
12/07/1995
 While driving the brake pedal went to the floor. tt
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC
08/01/2001
 There are problems with front brake discs. when consumer is stopping there is vibration coming from brakes.*ak
404/01/2000
 Front right brake caliper keeps pulling shortly after replacement. 4 have been replaced. sometimes a very strong pull where steering is pulled from hands. especially dangerious when pulling a travel trailer. -- fuel cell has a badly worn sleeve which causes floating suction to hang up causing air suction and running out of fuel at 1/2 tank plus or minus. *ak
06/01/1996
 When applying brakes vehicle will pulls hard to left . dealer has resurfaced front brakes, and flushed master cylinder and its lines, but defect keeps reoccurring. *ak
11/05/1998509/01/1995
 Excessive pedal effort required to stop vehicle in normal braking situations. front brakes smoke during hard stops or in stop and go traffic. it also gives off a burning smell. brought back to dealer 2 times and they state that it is normal. i just found out that in 1997, dodge changed the master cylinder on this truck to a larger unit. the rest of the brake system components are the same. i would think that this would solve my problem. *ak
10/14/19981
 While driving and applying the brakes there is a loud noise and the front brakes pads are gone completely and the rotors are in bad shape. contacted the manufacturer and they won't fix the vehicle unless the consumer pays for the repairs. *ak
1501/15/1996
 Front end misalignment. in addition, rear axle seals/axle bearings/steering drag:link/front brake calipers/rotors and pads/rear brake shoes and drums and rear brake cylinders and brake vacuum booster failed/replaced.
10/20/19974
 When applying the abs brakes the pedal will intermttently travel to the floor, causing extended stopping distance which nearly caused a collision. also, dealer replaced calipers/rotors and master cylinder. *ak
101/01/1996
 When appying the abs brakes, the vehicle pulls to the right and left sides. *ak consumr states at 12,000 miles there was extensive brake pad wear on front brakes, consumer contacted manufacturer and was advised they were aware of the braking problems.*jb
 When applying the brakes in damp weather, the front brakes lock up, causing the vehicle to slide.*ak
03/24/1996
 Disc brakes; the front right side brakes caught fire. *ak
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - CALIPER
06/01/1996
 The front brakes have pulled during braking from day 1. it is an admitted problem (by chrysler) with the calipers. mine have been replaced twice to no avail. *ak
06/18/19974
 When brakes are applied vehicle veers to the right; also, abs light and brake lights come on when pulling a trailer. in addition, replaced front brake rotors/pads/calipers. *ak
1
 Brake caliper failed.
04/17/1997
 Abs brake failure, made a loud noise , also, replaced disc pads/rotoes and calipers. *ak
12/30/19963
 When applying brakes, vehicle pulls severely to right, according to dealer, calipers were sticking, replaced calibers/ rotors, problem has reoccurred; also, experiencing lot of play in steering column, can m ove shaft u/down, not a tilted steering wheel. *ak
12/01/1996102/24/1996
 Front brake rotors malfunctioned, causing vehicle to pull; also, front brake pads/ calipers/power locks/gas gauge sender failed. *ak
11/18/19964
 Left/right front calipers malfunctioned, causing vehicle to pull left or right. *ak
04/04/1996
 When driving in the rain at 30 mph you have to apply so much brake pedal that the front abs brakes lock up; also, the brake pads have been replaced at 5,500 and 18,000 miles and the calipers have been rebuilt at 18,000 miles. *ak
1001/15/1996
 Front brake pads failed, causing vehicle to drift to the left on stops sometimes so severely that vehicle pulls out of lane; also replaced calipers/ rotors/torsion bar. *ak
03/18/1996703/16/1996
 Front brake pads/calipers failed, causing vehicle to pull to the right, also steering wheel off center. *ak
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - PADS
12/30/19981
 Axle seal failed, brake shoes replaced. *mjs
12/27/1998101/01/1996
 Initial transmission problem started @ 38000 just out of warranty. dealer said they couldn't help. i never thought of contacting manufacturer. trans. diagnosis complete at 72500 mis, dealer say rebuild, r+r at 89300mis. brake mastercylinder lid was leaking causing insufficiet fluid level lead to pad and shoe failure. transmission failure led to lifter failure in the engine. trans would long shift putiing strain on engine causing a higher rev. ultimately weakening 2 lifters. i am now hearing a noise and feeling jolts on the steering wheel turning left . problem is unknown at this time. *ak
05/03/1999107/01/1996
 The brake pads are also in need of changing at 50000 miles when they were changed at 22702miles by the dealership. something is wrong with the breaking system. *ak
09/18/1996101/19/1996
 Brake rotors out of round, brake pads failed resulting in vibration.
 When driving at various speed and applying brakes, vehicle pulls to the left. the harder pushes on brakes the harder vehicle pulls to left. consumer has to counter steer in order to avoid hitting oncoming traffic. has replaced brakes pads, but defect is still occurring. *ak
04/11/1998
 The brake pads separated from the shoe, causing the wheel to lock up. the dealer has been notified. *ak
08/08/1997
 Abs brake problems; intermittently when applying the brakes on dry road conditions, under normal braking, they seem to be very spongy, and the pedal travels to the floorboard. they do not stop the truck. all brake pads have be replaced on 3/7/98. the rear brakes pads were glazed over like they were heated up. *ak
08/03/1997303/19/1996
 Premature wear of front brake disc pads and shoes. also, brake shoe/drum adjusters failed.
06/18/19974
 When brakes are applied vehicle veers to the right; also, abs light and brake lights come on when pulling a trailer. in addition, replaced front brake rotors/pads/calipers. *ak
 Vehicles front disc brake system at 20,000 miles had 4 sets of pads and 3 sets of rotors .then, everything connected to the front braking system was changed. the manufacturer bought the vehicle back, they could not find the defect. *ak
10/14/1996103/27/1996
 Left front brake pad worn.
06/18/19961
 Front brake pads replaced.
04/17/1997
 Abs brake failure, made a loud noise , also, replaced disc pads/rotoes and calipers. *ak
04/10/19963
 Took vehicle to dealer and he said that the rear brakes are not working that's why the front brake need to have brake rotors and pads replaced every 10-1200 miles. vehicle went through 3 sets of front pads. the non-functioning rear brakes, causing front brakes to work harder. *ak
11/15/1995911/15/1995
 Vehicle's abs braking system has extreme premature wear and tear, had pads/rotors and other parts changed 9 times. *ak
12/01/1996102/24/1996
 Front brake rotors malfunctioned, causing vehicle to pull; also, front brake pads/ calipers/power locks/gas gauge sender failed. *ak
04/04/1996
 When driving in the rain at 30 mph you have to apply so much brake pedal that the front abs brakes lock up; also, the brake pads have been replaced at 5,500 and 18,000 miles and the calipers have been rebuilt at 18,000 miles. *ak
1001/15/1996
 Front brake pads failed, causing vehicle to drift to the left on stops sometimes so severely that vehicle pulls out of lane; also replaced calipers/ rotors/torsion bar. *ak
 In ten months the front rotor and pads wore out, vehicle has abs anti-lock brakes. please describe . *ak
03/18/1996703/16/1996
 Front brake pads/calipers failed, causing vehicle to pull to the right, also steering wheel off center. *ak
05/01/199605/11/1996
 Abs, brakes make a loud noise when coming to a stop, vehicle will jump when coming to a stop, also replaced front brake pads/ windshield wipr blade/rearview mirror. *ak
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - ROTOR
1
 The abs and the brake light illuminated. the vehicle brakes even when not in motion. the service writer says consumers vehicle needs a cabs computer module. the front rotors needed replacing because of what the dealer claims to be pitting. a friend in formed consumer that it was because of air bubbles in the casting when the rotors were made. *jg
04/01/1997
 Steering pitman arm and idler arm have a lot of play, front bearings loose, front rotors rusted and worn out required replacement. *ak
 When applying the brakes the pedal goes to the floor, causing extended stopping distance. replaced brakes five times within two years. also, the rotors are prematurley wearing. please give any further details. *ak
08/23/1996106/07/1996
 Rotors failed.
09/18/1996101/19/1996
 Brake rotors out of round, brake pads failed resulting in vibration.
103/04/1996
 Brake rotors warped due to overheating.
02/01/1996101/01/1996
 Front brake rotors warped.
06/18/19974
 When brakes are applied vehicle veers to the right; also, abs light and brake lights come on when pulling a trailer. in addition, replaced front brake rotors/pads/calipers. *ak
05/23/1997
 Brake problems; when applying the brakes the front end of vehicle virbrated . this was due to the rotors being warped. the rotors were resurfaced on 5/23/97. *ak
1
 Front rotors failed.
 Vehicles front disc brake system at 20,000 miles had 4 sets of pads and 3 sets of rotors .then, everything connected to the front braking system was changed. the manufacturer bought the vehicle back, they could not find the defect. *ak
03/10/19971
 Driver's side brake rotor out of round.
04/17/1997
 Abs brake failure, made a loud noise , also, replaced disc pads/rotoes and calipers. *ak
04/10/19963
 Took vehicle to dealer and he said that the rear brakes are not working that's why the front brake need to have brake rotors and pads replaced every 10-1200 miles. vehicle went through 3 sets of front pads. the non-functioning rear brakes, causing front brakes to work harder. *ak
11/15/1995911/15/1995
 Vehicle's abs braking system has extreme premature wear and tear, had pads/rotors and other parts changed 9 times. *ak
12/01/1996102/24/1996
 Front brake rotors malfunctioned, causing vehicle to pull; also, front brake pads/ calipers/power locks/gas gauge sender failed. *ak
1001/15/1996
 Front brake pads failed, causing vehicle to drift to the left on stops sometimes so severely that vehicle pulls out of lane; also replaced calipers/ rotors/torsion bar. *ak
 In ten months the front rotor and pads wore out, vehicle has abs anti-lock brakes. please describe . *ak
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM
1
 Consumer states brake shoes and brake drums were down to the metal and had to be replaced. *jb
09/03/1999102/01/1996
 Bracket for the emergency brake cable has fallen off due to nuts on the bolts securing the bracket becoming loose and both falling off. nuts are located behind the gas tank and are not accessable unless the gas tank is removed. emergency brake not operational.
07/04/1996605/15/1996
 Ongoing problem with rear brakes adjusting at least 5 different times. brakes fail to work. the self adjustor does not work. had to have them manually adjusted. *ak *ml
04/15/1996904/01/1996
 Rear brakes failed to stop vehicle when brakes were applied. front brakes working fine. sometimes front brakes lock up. took to dealer & was informed rear brakes functioned fine. found no problems. *ak *slc
08/03/1997303/19/1996
 Premature wear of front brake disc pads and shoes. also, brake shoe/drum adjusters failed.
03/10/19971
 Rear brakes replaced.
12/25/1996102/01/1996
 Brake drum failed.
12/02/1996101/13/1996
 Rear brake drums causing, severe vibration ( out-of-round). replaced but exhibiting identical symptoms.
112/05/1996
 Consumer was driving and applied the brakes vehicle could not stop, took to dealer, replaced the rear brake shoes and turned the drums . *ak. consumer states the rear brakes work for about 30 miles after dealer has replaced them , however then one has to stand on them for any braking power, consumer states that the front brakes are beginning to wear now due to they are the only ones operating on vehicle. *slc
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM - DRUM
1501/15/1996
 Front end misalignment. in addition, rear axle seals/axle bearings/steering drag:link/front brake calipers/rotors and pads/rear brake shoes and drums and rear brake cylinders and brake vacuum booster failed/replaced.
203/04/1996
 Drums warped due to overheating.
112/05/1996
 Consumer was driving and applied the brakes vehicle could not stop, took to dealer, replaced the rear brake shoes and turned the drums . *ak. consumer states the rear brakes work for about 30 miles after dealer has replaced them , however then one has to stand on them for any braking power, consumer states that the front brakes are beginning to wear now due to they are the only ones operating on vehicle. *slc
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM - SHOES/LININGS
08/09/1998506/24/1996
 The brakes were replaced at least 5 different times. brake lining overheats when brakes are applied. vehicle not stopping when brakes are applied quickly. dealer cannot find problem. *ak *ml
08/01/1996106/16/1996
 Brake shoes failed.
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM - WHEEL CYLINDERS
1501/15/1996
 Front end misalignment. in addition, rear axle seals/axle bearings/steering drag:link/front brake calipers/rotors and pads/rear brake shoes and drums and rear brake cylinders and brake vacuum booster failed/replaced.
08/15/1996103/27/1996
 Right/rear wheel cylinder leaks.
07/30/19961
 Replaced rear wheel cylinder.
07/18/1996106/06/1996
 Brake cylinder sensor bent.
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - HOSES, LINES/PIPING, AND FITTINGS
08/07/20000
 While driving to a stop sign behind other vehicle, applied brake pedal and vehicle lost braking power. consumer was forced to drive off the road. technician pointed out that problem was with brake line that delivered fluid to brakes. *ak
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - MASTER CYLINDER
06/18/20001
 While driving 50mph & went to apply brakes, master cylinder/power booster studs came out. it split the metal attachment. there were no brakes. rearended another vehicle. had contacted manufacturer. a representative checked vehicle's brakes & indicated the brakes were fine & manufacturer was not liable for anything.*ak
06/01/1996
 When applying brakes vehicle will pulls hard to left . dealer has resurfaced front brakes, and flushed master cylinder and its lines, but defect keeps reoccurring. *ak
12/27/1998101/01/1996
 Initial transmission problem started @ 38000 just out of warranty. dealer said they couldn't help. i never thought of contacting manufacturer. trans. diagnosis complete at 72500 mis, dealer say rebuild, r+r at 89300mis. brake mastercylinder lid was leaking causing insufficiet fluid level lead to pad and shoe failure. transmission failure led to lifter failure in the engine. trans would long shift putiing strain on engine causing a higher rev. ultimately weakening 2 lifters. i am now hearing a noise and feeling jolts on the steering wheel turning left . problem is unknown at this time. *ak
03/22/1999207/01/1997
 Brake master cylinder prematurely malfunctioned, causing the power brake booster to fail. also, caused the brake pedal to travel to the floor, resulting in extended stopping distance. *ak
11/05/1998509/01/1995
 Excessive pedal effort required to stop vehicle in normal braking situations. front brakes smoke during hard stops or in stop and go traffic. it also gives off a burning smell. brought back to dealer 2 times and they state that it is normal. i just found out that in 1997, dodge changed the master cylinder on this truck to a larger unit. the rest of the brake system components are the same. i would think that this would solve my problem. *ak
10/20/19974
 When applying the abs brakes the pedal will intermttently travel to the floor, causing extended stopping distance which nearly caused a collision. also, dealer replaced calipers/rotors and master cylinder. *ak
04/08/1996104/01/1996
 Master cylinder failed.
 Was driving and the abs and brake light came on, brake pedal went to the floor, took to dealer once and replaced the master cylinder, now the truck is at dealer for rear seal repair. *ak
03/01/1996112/30/1995
 Master cylinder cracked, causing brakes to pull.
08/31/19961
 Going to a camp ground on dirt road, hauling a trailer, going down a hill, driver tried to apply brakes (abs), had no brakes, ran into another vehicle w/trailer, the other vehicle literally stopped the vehicle at bottom of hill.*ak after inspection, it was found that the master cylinder was faulty. *slc
06/19/199605/28/1996
 Abs; went to apply the brakes and pedal went to the floor. lost all braking power, also replaced leaking master cylinder/booster . *ak
SERVICE BRAKES, HYDRAULIC - POWER ASSIST
07/18/199607/04/1996
 Failure of the abs brakes, causing loss of power assist, the brake pedal went to the floor.*ak
SERVICE BRAKES, HYDRAULIC - POWER ASSIST - HYDRAULIC
 The brake pump in the vehicle does not have enough boost in it to stop the vehicle correctly. there was a recall on brakes, but problem still exists (97v-068). *ak
SERVICE BRAKES, HYDRAULIC - POWER ASSIST - VACUUM
03/22/1999207/01/1997
 Brake master cylinder prematurely malfunctioned, causing the power brake booster to fail. also, caused the brake pedal to travel to the floor, resulting in extended stopping distance. *ak
02/07/1999110/01/1997
 The brakes have not been 100% since i purchased this vehicle. i took the vehicle to the dealer at41,000 miles and complained about low pedal . i was told that the pads and shoes were fine. at about 50,000 miles, the brake booster failed and the vehicle had to be towed to the dealer. squealing noise from under the hood was found to be the water pump.
05/01/1997
 There is no reserve canister for brake vacuum causing loss of brakes in heavy stop and go traffic.
1501/15/1996
 Front end misalignment. in addition, rear axle seals/axle bearings/steering drag:link/front brake calipers/rotors and pads/rear brake shoes and drums and rear brake cylinders and brake vacuum booster failed/replaced.
06/19/199605/28/1996
 Abs; went to apply the brakes and pedal went to the floor. lost all braking power, also replaced leaking master cylinder/booster . *ak
SERVICE BRAKES, HYDRAULIC - POWER ASSIST - VACUUM - HOSES, LINES/PIPING, AND FITTINGS
12/09/2003984491
 The vehicle vacuum system became contaminated with oil. this effected the vehicle's hav system, brake booster and deteriorated all the vacuum hoses which caused the brakes to fail intermittently. *ph a recall was initiated for this problem but the consumer's vehicle was not included due to vin. the dealer recommended that the consumer install an external brake booster check valve and hose, replace vent and defroster actuator. the customer declined the repairs. *nm
09/17/20031270002
 While driving at any speed vehicle took a long time to slow down when the brake pedal was pressed. brake light stayed on, and oil was leaking into the vacuum system. *ak
09/26/1997102/01/1996
 Recall work done on the abs check valve, however loss of brakes and problems with system after recall work..
12/02/1997103/07/1996
 Power vacuum lines failed, causing loss of brakes prior to recall.
12/02/1997103/07/1996
 Recall #97068, dealer replaced the vacuum check valve in the brake pump in which the problem still exists. the vehicle experiences no braking ability. had to use the emergency parking brake in order to stop. *ak consumer states the rubber vacuum fitting on line between pump and brake booster dislodged vacuum, oil fumes reacted to rubber and became unstable, this occurred after recall, all fittings have been replaced with better rubber fittings. *slc