Bulletins
| Bulletin | Bulletin date | Replacement Bulletin | Item no. | Summary | Added |
|---|---|---|---|---|---|
| STEERING | |||||
| 0538 | 02/21/2005 | 10012950 | Increased turning effort during low speed sharp turns false 4x4 engagement. *eh | 04/05/2005 | |
Investigations
| NHTSA ID | Manufacturer | Date open | Date close | Subject | Recall campaign | |
|---|---|---|---|---|---|---|
| STEERING | ||||||
| EA09013 | Ford Motor Company | 08/18/2009 | 02/12/2013 | Vehicle Rollaway Allegations | ||
| This investigation is being closed based on several considerations.by the most inclusive counting of all alleged rollaway incidents (i.e., counting all alleged rollaway incidents and assuming a singular failure mechanism), the incident rate is low, however during ea09-013, odi identified a number of different failure mechanisms in 180 incidents related to the alleged defect.the highest rate for any particular failure mechanism, the failure of the automatic transmission parking system, was 4.4/100k.the next-highest failure rate was for the bsi system, at 3.4/100k.for all identified failure mechanisms there has been a drastically declining trend including very few incidents occurring in recent years.accordingly, this investigation is closed.the closing of this investigation does not constitute a finding by nhtsa that a safety-related defect does not exist.for additional information regarding this investigation, see the complete closing resume in the document file for ea09-013. the odi reports cited above can be reviewed at www-odi.nhtsa.dot.gov/complaints under the following identification (odi) numbers:10168454, 10279630, 10280078. | ||||||
| PE09020 | FORD MOTOR COMPANY | 04/21/2009 | 08/19/2009 | VEHICLE ROLLAWAY ALLEGATIONS | ||
| In response to an information request (ir) letter sent by the office of defects investigation (odi), ford stated consumer reports of higher than expected efforts when shifting into and out of park could be a result of a groove being worn into the swing arm ramp of the steering column. the swing arm is a component bolted to the steering column that assists in shifting through the transmission gears.an engineering evaluation conducted by ford of returned steering columns found the groove could be created over time if consumer shift more quickly from the drive or reverse to park than the brake shift interlock (bsi) solenoid pin retracts after the brake pedal is applied. in november of 2004, ford released a redesigned bsi solenoid with a shorter pin retracting time as a serviceable component. ford has noted the shorter retraction time significantly lessens the likelihood of bsi solenoid pin to swing arm contact even with rapid consumer shifts.ford also issued a technical service bulletin, tsb 04-22-12, to instruct service technicians on the proper diagnosis and vehicle repair. reviewing complaints to odi and data submitted by ford, odi has identified 200 alleged incidents of unintended vehicle movement after consumers believe they have shifted the vehicle into park, resulting in 85 alleged crashes and 32 alleged injuries.in addition to the reports of alleged incidents of unintended vehicle movement, odi has also identified 883 reports of consumers alleging difficulty or the inability to shift the vehicle into park.this preliminary evaluation has been upgraded to an engineering analysis (ea09-013) to further assess the scope, frequency and risk to motor vehicle safety of the alleged defect in the subject vehicles. | ||||||
| EA09013 | FORD MOTOR COMPANY | 08/18/2009 | VEHICLE ROLLAWAY ALLEGATIONS | |||
| In response to an information request (ir) letter sent by the office of defects investigation (odi), ford stated consumer reports of higher than expected efforts when shifting into and out of park could be a result of a groove being worn into the swing arm ramp of the steering column. the swing arm is a component bolted to the steering column that assists in shifting through the transmission gears.an engineering evaluation conducted by ford of returned steering columns found the groove could be created over time if consumers shift more quickly from the drive or reverse to park than the brake shift interlock (bsi) solenoid pin retracts after the brake pedal is applied. in november of 2004 ford released a redesigned bsi solenoid with a shorter pin retracting time as a serviceable component. ford has noted the shorter retraction time significantly lessens the likelihood of bsi solenoid pin to swing arm contact even with rapid consumer shifts.ford also issued a technical service bulletin, tsb 04-22-12, to instruct service technicians on the proper diagnosis and vehicle repair. reviewing complaints to odi and data submitted by ford, odi has identified 200 alleged incidents of unintended vehicle movement after consumers believe they have shifted the vehicle into park, resulting in 85 alleged crashes and 32 alleged injuries.in addition to the reports of alleged incidents of unintended vehicle movement, odi has also identified 883 reports of consumers alleging difficulty or the inability to shift the vehicle into park.preliminary evaluationpe09-020 has been upgraded to an engineering analysis to further assess the scope, frequency and risk to motor vehicle safety of the alleged defect in the subject vehicles. | ||||||
| STEERING - COLUMN | ||||||
| EA09013 | Ford Motor Company | 08/18/2009 | 02/12/2013 | Vehicle Rollaway Allegations | ||
| This investigation is being closed based on several considerations.by the most inclusive counting of all alleged rollaway incidents (i.e., counting all alleged rollaway incidents and assuming a singular failure mechanism), the incident rate is low, however during ea09-013, odi identified a number of different failure mechanisms in 180 incidents related to the alleged defect.the highest rate for any particular failure mechanism, the failure of the automatic transmission parking system, was 4.4/100k.the next-highest failure rate was for the bsi system, at 3.4/100k.for all identified failure mechanisms there has been a drastically declining trend including very few incidents occurring in recent years.accordingly, this investigation is closed.the closing of this investigation does not constitute a finding by nhtsa that a safety-related defect does not exist.for additional information regarding this investigation, see the complete closing resume in the document file for ea09-013. the odi reports cited above can be reviewed at www-odi.nhtsa.dot.gov/complaints under the following identification (odi) numbers:10168454, 10279630, 10280078. | ||||||
| EA09013 | FORD MOTOR COMPANY | 08/18/2009 | VEHICLE ROLLAWAY ALLEGATIONS | |||
| In response to an information request (ir) letter sent by the office of defects investigation (odi), ford stated consumer reports of higher than expected efforts when shifting into and out of park could be a result of a groove being worn into the swing arm ramp of the steering column. the swing arm is a component bolted to the steering column that assists in shifting through the transmission gears.an engineering evaluation conducted by ford of returned steering columns found the groove could be created over time if consumers shift more quickly from the drive or reverse to park than the brake shift interlock (bsi) solenoid pin retracts after the brake pedal is applied. in november of 2004 ford released a redesigned bsi solenoid with a shorter pin retracting time as a serviceable component. ford has noted the shorter retraction time significantly lessens the likelihood of bsi solenoid pin to swing arm contact even with rapid consumer shifts.ford also issued a technical service bulletin, tsb 04-22-12, to instruct service technicians on the proper diagnosis and vehicle repair. reviewing complaints to odi and data submitted by ford, odi has identified 200 alleged incidents of unintended vehicle movement after consumers believe they have shifted the vehicle into park, resulting in 85 alleged crashes and 32 alleged injuries.in addition to the reports of alleged incidents of unintended vehicle movement, odi has also identified 883 reports of consumers alleging difficulty or the inability to shift the vehicle into park.preliminary evaluationpe09-020 has been upgraded to an engineering analysis to further assess the scope, frequency and risk to motor vehicle safety of the alleged defect in the subject vehicles. | ||||||
| PE09020 | FORD MOTOR COMPANY | 04/21/2009 | 08/19/2009 | VEHICLE ROLLAWAY ALLEGATIONS | ||
| In response to an information request (ir) letter sent by the office of defects investigation (odi), ford stated consumer reports of higher than expected efforts when shifting into and out of park could be a result of a groove being worn into the swing arm ramp of the steering column. the swing arm is a component bolted to the steering column that assists in shifting through the transmission gears.an engineering evaluation conducted by ford of returned steering columns found the groove could be created over time if consumer shift more quickly from the drive or reverse to park than the brake shift interlock (bsi) solenoid pin retracts after the brake pedal is applied. in november of 2004, ford released a redesigned bsi solenoid with a shorter pin retracting time as a serviceable component. ford has noted the shorter retraction time significantly lessens the likelihood of bsi solenoid pin to swing arm contact even with rapid consumer shifts.ford also issued a technical service bulletin, tsb 04-22-12, to instruct service technicians on the proper diagnosis and vehicle repair. reviewing complaints to odi and data submitted by ford, odi has identified 200 alleged incidents of unintended vehicle movement after consumers believe they have shifted the vehicle into park, resulting in 85 alleged crashes and 32 alleged injuries.in addition to the reports of alleged incidents of unintended vehicle movement, odi has also identified 883 reports of consumers alleging difficulty or the inability to shift the vehicle into park.this preliminary evaluation has been upgraded to an engineering analysis (ea09-013) to further assess the scope, frequency and risk to motor vehicle safety of the alleged defect in the subject vehicles. | ||||||
| STEERING - COLUMN LOCKING - ANTI-THEFT DEVICE | ||||||
| EA09013 | Ford Motor Company | 08/18/2009 | 02/12/2013 | Vehicle Rollaway Allegations | ||
| This investigation is being closed based on several considerations.by the most inclusive counting of all alleged rollaway incidents (i.e., counting all alleged rollaway incidents and assuming a singular failure mechanism), the incident rate is low, however during ea09-013, odi identified a number of different failure mechanisms in 180 incidents related to the alleged defect.the highest rate for any particular failure mechanism, the failure of the automatic transmission parking system, was 4.4/100k.the next-highest failure rate was for the bsi system, at 3.4/100k.for all identified failure mechanisms there has been a drastically declining trend including very few incidents occurring in recent years.accordingly, this investigation is closed.the closing of this investigation does not constitute a finding by nhtsa that a safety-related defect does not exist.for additional information regarding this investigation, see the complete closing resume in the document file for ea09-013. the odi reports cited above can be reviewed at www-odi.nhtsa.dot.gov/complaints under the following identification (odi) numbers:10168454, 10279630, 10280078. | ||||||
| PE09020 | FORD MOTOR COMPANY | 04/21/2009 | 08/19/2009 | VEHICLE ROLLAWAY ALLEGATIONS | ||
| In response to an information request (ir) letter sent by the office of defects investigation (odi), ford stated consumer reports of higher than expected efforts when shifting into and out of park could be a result of a groove being worn into the swing arm ramp of the steering column. the swing arm is a component bolted to the steering column that assists in shifting through the transmission gears.an engineering evaluation conducted by ford of returned steering columns found the groove could be created over time if consumer shift more quickly from the drive or reverse to park than the brake shift interlock (bsi) solenoid pin retracts after the brake pedal is applied. in november of 2004, ford released a redesigned bsi solenoid with a shorter pin retracting time as a serviceable component. ford has noted the shorter retraction time significantly lessens the likelihood of bsi solenoid pin to swing arm contact even with rapid consumer shifts.ford also issued a technical service bulletin, tsb 04-22-12, to instruct service technicians on the proper diagnosis and vehicle repair. reviewing complaints to odi and data submitted by ford, odi has identified 200 alleged incidents of unintended vehicle movement after consumers believe they have shifted the vehicle into park, resulting in 85 alleged crashes and 32 alleged injuries.in addition to the reports of alleged incidents of unintended vehicle movement, odi has also identified 883 reports of consumers alleging difficulty or the inability to shift the vehicle into park.this preliminary evaluation has been upgraded to an engineering analysis (ea09-013) to further assess the scope, frequency and risk to motor vehicle safety of the alleged defect in the subject vehicles. | ||||||
| EA09013 | FORD MOTOR COMPANY | 08/18/2009 | VEHICLE ROLLAWAY ALLEGATIONS | |||
| In response to an information request (ir) letter sent by the office of defects investigation (odi), ford stated consumer reports of higher than expected efforts when shifting into and out of park could be a result of a groove being worn into the swing arm ramp of the steering column. the swing arm is a component bolted to the steering column that assists in shifting through the transmission gears.an engineering evaluation conducted by ford of returned steering columns found the groove could be created over time if consumers shift more quickly from the drive or reverse to park than the brake shift interlock (bsi) solenoid pin retracts after the brake pedal is applied. in november of 2004 ford released a redesigned bsi solenoid with a shorter pin retracting time as a serviceable component. ford has noted the shorter retraction time significantly lessens the likelihood of bsi solenoid pin to swing arm contact even with rapid consumer shifts.ford also issued a technical service bulletin, tsb 04-22-12, to instruct service technicians on the proper diagnosis and vehicle repair. reviewing complaints to odi and data submitted by ford, odi has identified 200 alleged incidents of unintended vehicle movement after consumers believe they have shifted the vehicle into park, resulting in 85 alleged crashes and 32 alleged injuries.in addition to the reports of alleged incidents of unintended vehicle movement, odi has also identified 883 reports of consumers alleging difficulty or the inability to shift the vehicle into park.preliminary evaluationpe09-020 has been upgraded to an engineering analysis to further assess the scope, frequency and risk to motor vehicle safety of the alleged defect in the subject vehicles. | ||||||
Consumer Complaints
| Fail date | miles | occurences | Purchase date |
|---|---|---|---|
| STEERING | |||
| 02/21/2009 | 48958 | ||
| I own a 2005 ford explorer that i purchased in june, 2005. on saturday, february 21, 2009, i attempted to shift my 2005 ford explorer, which had roughly 49,000 miles driven at the time, into reverse in order to back out of my driveway. in doing so, the gearshift almost completely broke away from the steering column. i was able to turn the ignition off, but was unable to remove the key from the ignition. after having the vehicle towed to the dealer, i was informed that the gearshift is not a serviceable part and that the entire steering column would need to be replaced. the service representative stated she had never seen this issue before, it was not covered under warranty, and the cost for a new steering column and associated labor would be more than $1,600. she also informed me that a used steering column from a junkyard would cost much less, but that she would not be able to provide the exact amount until early monday morning. on monday morning, i was informed by krf south that they could obtain a used steering column and the total costs for parts and labor would be $620. i chose to have the used used steering column installed due to the price differential. simply put, a gearshift should not break off from the steering column through normal vehicle use. i believe this to be a serious safety issue that should be addressed by ford. i was fortunate enough to be able to turn off the ignition after the gearshift broke away. had i not been able to turn the vehicle off, i would have needed to remain in the vehicle with my foot on the brake until i could get assistance. now i have a replaced steering column, with the everlasting thought that the gearshift could break off at any point in the future. i have a wife and 3 small children and i am hesitant about her using the vehicle due to the fact this may very well happen again. | |||
| 11/14/2009 | 80000 | ||
| I own a 2005 ford explorer. this incident happened in november of 2009. the ford explorer had approximately 80,000 miles on it. i pulled into my sister's driveway which is a flat, gravel driveway. the ford explorer is an automatic transmission. i shifted the car into park and then exited the ford explorer. after exiting the ford explorer, it started moving backwards. the open door knocked me down and then the tire on the driver's side ran over my leg. my sister ran and stopped the car. the gear shift moved from park into reverse. | |||
| 07/21/2007 | 45000 | ||
| Tl* the contact owns a 2005 ford explorer. when attempting to start the vehicle, the engine began to sputter. she restarted the vehicle to resume normal vehicle operation. on another occasion while driving, the power steering and brakes failed without warning, which caused her to crash into a fence. the vehicle was taken to an independent mechanic for inspection on two separate occasions. the failure was contributed to the fuel sensor and throttle position sensor. the throttle position sensor was replaced. the repair did not remedy the failure. the failure mileage was 45,000. the current mileage was 80,000. the vehicle identification number was unavailable. | |||
| STEERING - ELECTRIC POWER ASSIST SYSTEM | |||
| 06/22/2006 | 5000 | 8 | 01/28/2005 |
| I have a 2005 ford explorer eddie bauer which looses power steering control and braking ability at random. i have taken this vehicle into service at the dealership for repair but no satisfactory outcome is there. for the first problem of loosing the braking ability, the vehicle when started has no problems but after driving a short distance (few meters to up to a mile) the advance traction loss message is displayed in the message centre and the vehicle looses the ability to stop in the required stop distance. when applying the brakes, the pulsation is felt in the brake paddle and a screeching heard before the vehicle stops. then once the engine is turned off, and vehicle re-started, the message is reset and vehicle works fine. the second issue is that the vehicle while driving, at random gives the message in the display with an audio signal indicating oil pressure low, service engine soon and other lights in the display and rpm meter showing zero reading with loss of steering ability. there is no power assist to turn the steering whereas the engine is running and also vehicle accelerates if pedal is pushed. i have been into the dealership thrice but the problem is yet to be fixed from last 15 months. the control on the vehicle can be got back once the engine is switched off and restarted. i have resorted to putting the vehicle in neutral and let it roll and turn the engine off and then restart it and get the steering control back. i had left the vehicle at the dealership in oct 2005 for 10 days to diagnose and rectify but i was advised that problem has been reported to the authorities at ford but i am yet to hear back from the dealer or the oem. *nm | |||
| STEERING - GEAR BOX (OTHER THAN RACK AND PINION) | |||
| 02/21/2006 | 5248 | 1 | 05/01/2005 |
| Dt*: the contact stated while the vehicle was parked, fluid was discovered on the driveway from an unknown source. upon further inspection, the steering gear box was leaking power steering fluid. although the vehicle was not seen by a dealer, the contact continued to monitor the power steering fluid level. | |||