Bulletins
| Bulletin | Bulletin date | Replacement Bulletin | Item no. | Summary | Added |
|---|---|---|---|---|---|
| SERVICE BRAKES, AIR - DISC - ROTOR | |||||
| 9845 | 03/02/1998 | 601264 | Availability of hub-mount brake rotor machining equipment. *yc | 07/15/1998 | |
| SERVICE BRAKES, HYDRAULIC | |||||
| 99411 | 03/08/1999 | 604767 | Vehicles experiencing increased brake pedal effort and / or false abs cycling at low speeds, or abs lamp illumination. *tt | 05/12/1999 | |
| SERVICE BRAKES, HYDRAULIC - ANTILOCK | |||||
| 991313 | 06/28/1999 | 606515 | Subject regarding anti-lock brake lamp illumination, increased break pedal effort and / or false anti-lock brake system (abs) cycling at low speeds. *tt | 08/26/1999 | |
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS | |||||
| 99194 | 09/20/1999 | 6090082 | Information for servicing and diagnosing brake vibration, brake inspection, and brake friction material replacement. *tt | 03/06/2000 | |
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - ROTOR | |||||
| 9814 | 01/19/1998 | 605562 | Subject regarding the availability of hub-mount brake rotor machining equipment. *tt | 07/09/1999 | |
| 985A5 | 03/18/1998 | 601003 | Hub-mount brake rotor machining equipment from rotunda is now approved for warranty and service use. *yc | 06/17/1998 | |
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM | |||||
| 99107 | 06/01/1999 | 606482 | Conditions on rear drum grabbing during first few brake applications while brakes are cold. *tt | 08/25/1999 | |
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM - DRUM | |||||
| 01192 | 10/01/2001 | 627680 | Some vehicles may exhibit a grabbing condition from the rear drum brakes during the first few brake applications after extended humidity exposure. *tt | 02/13/2002 | |
Consumer Complaints
| Fail date | miles | occurences | Purchase date |
|---|---|---|---|
| SERVICE BRAKES, AIR - ANTILOCK - ABS WARNING LIGHT | |||
| 03/01/1998 | 2 | 03/01/1998 | |
| Abs sensor. | |||
| SERVICE BRAKES, HYDRAULIC | |||
| 11/07/2008 | 112000 | 1 | |
| I purchased a 1998 ford f-150 in 2000 from carmax in arlington, tx. i have had no major problems until nov. 7th 2008. i was driving and approached a traffic signal. i attempted to depress my brakes when the vehicle locked up and spun sideways at the intersection. when i exited the vehicle i found that my driverside rear differential had broken lose and the rear differential clamp had broken off allowing the entire driverside differential to fly off of the vehicle. % minutes earlier i was on the freeway. if this would of happened on the freeway, i would not be here today. *tr | |||
| 11/07/2007 | 68700 | 1 | 11/14/2000 |
| Tl*the contact owns a 1998 ford f150. while idling at a traffic light with the brake pedal depressed, the vehicle began to roll until it crashed into another vehicle. no warning lights were illuminated. aaa towed the vehicle and the brake lines were replaced. he has not notified the manufacturer. the contact has pictures of the defective brake lines. the current and failure mileages were 68,700. updated 01-11-08. *kb updated 12/12/07 *tr | |||
| 08/13/2007 | 1 | ||
| Hydraulic brake failure. vehicle towed to repair facility. rear brake lines replaced due to corrosion. *tr | |||
| 09/05/2005 | 0 | ||
| Brake were not right spongy. wearing out bake pad's nothing happened yet but not working right as of now. i replaced caliper and pad's. and brakes are still dragging. *nm | |||
| 07/15/2001 | 1 | ||
| Consumer states why he was driving in the rain and attempted to apply his antilock brakes they locked on him , causing him to have accident. no injuries were sustained. | |||
| SERVICE BRAKES, HYDRAULIC - ANTILOCK | |||
| 06/17/2004 | 1 | ||
| While driving at 30 mph pplied the brakes.and brake pedal went to the floor, and there were no brakes. this resulted in in extended stopping distance. dealer notified. *ak | |||
| 01/02/2004 | 1 | 07/07/1998 | |
| Abs brake problems; when applying brakes in an emergency situation, under wet road conditions, the system locked up, resulting in a roll over. i had noticed this in the past and took it to a dealer and was told it was just the natural for a ford. *ak | |||
| 02/01/2003 | 86500 | 08/26/1998 | |
| When applying the brakes, the pedal seems to jerk and slow to stop. when coming to a stop there is a ticking noise, it seem to be coming from the firewall. the abs light has came on several occasion. i've had both set of brakes serviced and rotors turned three different times and still have problem. *nlm | |||
| 04/01/2099 | |||
| On april 2, 2000 while traveling on the parks hwy. this vehicle accelerated & continued to accelerate out of the driver's control. the brakes were applied heavily for three quarters of a mile or more in order to slow the vehicle & find a place to pull to the side and attempt to turn the vehicle off. once this was achieved, the vehicle restarted normally. nye ford service dept. was contacted & a pcv kit was installed by that dealership on april 19, 2000. on august 13, 2002 this vehicle again accelerated & continued to accelerate out of the driver's control. the same procedure was used to stop t he vehicle. the vehicle started normally on the fourth attempt. during the first 3 attempts to restart the vehicle, the engine was revving out of control.*ak | |||
| 09/01/2002 | |||
| Brake pedal will go all the way to the floor. brakes are warped. dealership is aware of problem. *ak | |||
| 11/20/2001 | 4 | ||
| While making a right hand turn consumer tapped the brakes and felt abs coming on, but vehicle did not slowdown, had to use emergency brakes to stop, it usually happens with a hard turn, consumer felt that if it happened on a busy street someone could had been injured. *ak consumer stated that the wires which are going from brake to the right front tire, were giving a false reading of a tire lock up. *yd | |||
| 08/05/2001 | |||
| Anti-lock braking system is ineffective when a sudden stop needs to be made. also, brakes will begin to grap, then release. dealer has been contacted. please provide further details. consumer was almost involved in three collisions. *ak | |||
| 1 | |||
| Intermittently when the brakes are applied pedal pulsates, resulting in extended stopping distance. dealer has changed pads and rotors. however, problem still exists. *ak slc | |||
| 08/29/2001 | 1 | 07/01/1998 | |
| Proceeded down wet highway at 40 mph. vehicle ahead slowed. applied brakes, had full lockup and hit car ahead at est 7 mph speed. antilock system did not activate at all. had noticed tis phenomena at stop signs in wet condition before, had checked at dealer, no problem found by technician. i feel that this is a problem associated only with wet road conditions. software problem rather than mechanical. am aware of other cases. although my damage minor, i feel this should be investigated due to potential serious nature of problem.*ak | |||
| 07/16/2001 | 1 | 04/01/2001 | |
| Brakes failed after continous stop and go traffic. no abs, no stopping 35900 miles.*ak | |||
| 1 | 06/01/1998 | ||
| While having vehicle serviced technician noticed rear brakes were not working properly due to abs valve not working. please provide fusrther information.*ak | |||
| 08/03/2001 | |||
| While traveling at 55 mph another vehicle pulled out in front of consumer's vehicle, consumr depressed brake pedal with force, causing wheels to lock up. consumer lost control of vehicle, and ran into other vehicle. please provide further information.*ak | |||
| 09/23/1998 | 5 | 10/25/1997 | |
| The rear brakes were inoperative due to a malfunction in the system therefore the front brakes were doing all the work and causing the vehicle to jump to a stop and skid in traffic, the front brakes and rotors had to be replaced as a result of the malfunction, the system malfunction was covered under extended warranty but the front brakes and rotors were not. nlm | |||
| 04/01/2001 | |||
| While driving on road consumer stepped on gas and pedal got stuck. consumer could not press on brake to slow vehicle down. so consumer put vehicle in nuetral, and finally stopped vehicle. contacted dealer, and dealer replaced throttle body. *ak | |||
| 02/13/2001 | |||
| While driving downhill at 30 mph, applied brake and pedal went to floor. consumer used emergency brake, and dropped to low 1 to slow vehicle down. it felt like a brake line leak. dealer replaced brake sensor. *ak | |||
| 06/15/1999 | |||
| Ongoing problem with abs brakes causes rear wheels to lock up when applying brakes on wet/damp road. it also causes extended stopping distance. also, a problem with courtesy lights, and running tail lights momentarily remain on from 2 minutes up to 2 hours before turning off, even after vehicle was turned off. dealer/manufacturer were not notified at this time. please feel free to provide any further details on this matter. *ak | |||
| 11/19/2000 | 2 | 02/12/1998 | |
| Recall 98v007000/throttle icing: speed control will not disengage when applying brakes, and intermittent problem with brake pedal going to floor. *ak 2 goodyear wrangler ap tire's tread is completely gone, size p255/70r16, dot pdcuf8wr038. consumer states engine has a ping sound when first started in cold weather, dealership is aware of the problem. *slc | |||
| 12/01/1997 | 20 | 10/01/1997 | |
| Two months after i purchased the vehicle, i noticed when on icy, snowy, or similar slippery surfaces, the anti-lock braking system locked-up and did not anti-lock as designed. this is evidenced by my rear-end sliding around sideways and no reverse brake petal pressure. i had previously owned a vehicle that had anti-lock brakes and the brake petal would push against my foot and make a vibrating noise when activated. this does not occur on this vehicle. also, when the vehicle is cold, all four brakes will lock up when any petal pressure is applied--especially at low speeds such as pulling out of my driveway or out of a parking lot. this was brought to the attention of the ford dealer nearest my residence (not the dealer i originally purchased the truck) on two separate occasions. the first time i took it in was at my 30,000 mile check-up about 10 months after i purchased the vehicle (august 27, 1998). they checked brakes and noted on the service invoice could not verify. the second time i took it in was about 7 months later (march 8, 1999) after the winter season was over and had them check the system and no service was noted or performed. i took at face value that when they said nothing was wrong that there wasn't anything wrong. however, anti-lock brakes are not something that you can check year round but rather only when the pavement is slippery. they said they checked them by putting heavy pressure on the brakes and then pressing the gas pedal and ruled out failure of the abs. i am here to tell you that even today, they still lock-up and do not function properly. i can send you photocopies of the service invoices if needed. *ak | |||
| While depressing brakes vehicle goes into extended stopping distance. dealer has been notified, but problem continued. please provide further information. *ak | |||
| 12/02/2000 | |||
| Vehicle was hit head-on. upon impact, vehicle exploded, resulting in minor injuries. dealer has been notified, and the manufacturer will be notified. *ak | |||
| 12/20/1997 | |||
| Ongoing / intermittent problem when applying brakes in a sudden stop / emergency situation, it causes rear wheels to lock up. vehicle been in dealer shop on two occasions, and problem still reoccurring. please feel free to provide any further details on this matter. *ak | |||
| 04/01/1999 | |||
| At slow speed when brakes are applied, brakes don't work. abs sensor has been replaced by dealer 5 times for this problem. *ak | |||
| 04/17/1998 | 04/01/1998 | ||
| The dealer has addressed the brake issue by turning rotors/drums. 10,000 miles later im having the same problem, there seems to be a problem with braking equalization from front to rear. the rear brakes have yet to show signs of wear. overall the vehicle is running good but it appears the few on going problems are going to cost me after warranty is over.*ak | |||
| 09/05/1999 | 1 | ||
| Left front wheel locks up. when this happens, vehicle starts sliding. dlr can't duplicate the problem.*ak | |||
| 03/24/2000 | 01/01/2000 | ||
| This dealership does business in an unsafe, fraudlent, manner. i have documentation proving this claim .no safety defect listed. *ak | |||
| 01/01/2000 | 6 | ||
| Whenever applying brakes intermittently it caused vehicle to surge forward. pedal would get hard, and vehicle would continue on before stopping. vehicle has been in/out of dealer shop on six occasions, dealer informed consumer that nothing could be found. feel free to provide further details.*ak | |||
| 03/15/2000 | 1 | 11/01/1999 | |
| While driving in town and approaching a stop sign or light, applied brakes, left rear wheels locked up and vehicle slid. contacted dealer, they cleaned the brakes, and couldn't find any problem. while leaving the lot, vehicle started to do the same thing. service consultant said that wheels were supposed to lock up when wet. for now problem has been solved by making adjustments to the rear brakes. *ak *ml | |||
| 05/05/2000 | 1 | 11/01/1999 | |
| I took the truck in and the service consultant said that the brakes were working normally eventhough the rear ones did lock up at 20 m.p.h. or slower when leaving the parking lot of their lot. *ak | |||
| 05/05/2000 | 1 | 11/01/1999 | |
| While driving, i would come up to a stop sign or light and apply the brakes and the left rear brake would lock up. i took it in and they looked at the brakes and said they were ok. i went to leave and it did it again. i went back in and told them that they were still doing it and they said that it was normal for the abs to do that. i went back the next day and they adjusted the brakes and now they do what they are suppose to do. it could be possible that one of the self adjusters might not be working. *ak | |||
| 6 | 10/01/1998 | ||
| Brakes fail when depressed, then grab at last second. dealer performed a brake service consisting of grinding the metallic pads but problem is worse and brakes now groan upon stop. *ak | |||
| 06/06/1998 | |||
| When applying brakes during normal braking brakes locked up, causing the truck to slide. driver has lost control of the vehicle many times. this has happened during inclement weather ,aftet the truck has set for a while. problem was reported to the dealer. dealer stated that problem was due to the rear brake shoes and not the abs. problem has not been corrected. please provide any further information. *ak | |||
| 11/01/1998 | 2 | 03/01/1998 | |
| Deal has attempted to fix both brakes and the door cracks: brakes still do not work and door cracked again. dealer now will not fix them again. *ak | |||
| While driving in a parking lot and applying the brakes, pedal went the floor, the vehicle accelerated out of control, causing a collision. please give any further details. *ak | |||
| 04/11/1999 | 20 | 07/01/1998 | |
| Truck anti lock brakes lock up when ever it rains or gets wet. dealer attempted to fix 4 times, still lock up. | |||
| The bushings on the spindle are too big which causes the brakes to lock up/grind and overheat. please give any further details. *ak | |||
| 06/17/1999 | |||
| While driving at 70 mph and applying the brakes on wet pavement, vehicle didn't stop and went straight through a red light, and the front right wheel locked up when applying the brakes real hard while trying to stop. *ak | |||
| 08/01/1998 | 1 | 08/29/1998 | |
| While depressing brake pedal vehicle continues traveling, resulted in an accident. *ak *ml | |||
| While driving on a wet surface and applying the brakes, the vehicle feels as if it has lost power in the brakes. then the brakes lock up and the vehicle skids. dealer can't duplicate the problem. *ak | |||
| When applying the brakes on dry pavement back brakes grab, but the front brakes do not, causing extended stopping distance. at 22,000 miles the brake pads and rotors were replaced. at 28,000 miles the problem has returned. please provide any further details. *ak | |||
| 11/28/1998 | 1 | 02/01/1998 | |
| Rear abs brakes locked up. *yc | |||
| 06/03/1999 | |||
| Abs brake problems; when applying brakes in an emergency situation, under wet road conditions, the system locked up, resulting in a rear end crash. truck is being repaired. please provide any further details. *ak | |||
| 04/15/1999 | 3 | ||
| Consumer took vehicle to dealership more than three times for transmission, and dealer said the problem were the brakes. the transmission has been taken out, and the brakes were repaired three times. *ak | |||
| 05/14/1999 | |||
| Driver's side door and passager's side doors have cracks within the frame and panel. both door's are rusting at the bottom when driving at 25 mph on wet pavement. also, when applying brakes rear brake's will lock up. *ak | |||
| 01/03/1999 | |||
| On-going/intermittent problem with abs brakes locking up during 5 mph or more; condition was reported to manufacturer. but nothing can be done at this time. seeking help from nhtsa in this matter. *ak | |||
| 02/15/1999 | 1 | ||
| Anti lock brake module failed causing light to illuminate. mjs | |||
| 03/30/1999 | 1 | 09/01/1998 | |
| While traveling in the right hand lane, i noticed an abandoned vehicle in the road ahead of me. i attempted to slow down and pull behind the vehicle to my right to avoid a collision. when my truck did not noticeably begin to slow, i attempted to bring my truck to a complete stop. i increased pressure on th brake pedal. the truck began very difficult to control and slowly began to decrease speed. after approx 100 yds i felt the brakes began to grab and was pulled forward against the seat belt. i had already traveled an excessive distance, and once the brakes began to work there was nto enough space left to bring my vehicle to a complete stop. this resulted in my truck ramming into the abonded vehicle at 5-15 mph. *ak | |||
| 08/24/1998 | |||
| When brakes are applied they become mushy, resulting in extended stopping distance. the dealer has been notified. *ak | |||
| Consumer has abs brakes. brake failure occurred twice in rainy conditions in which the brake pedal went to floor of vehicle, causing vehicle not to stop. also, vehicle has no control when brakes are applied. problem is intermittent. dealers cannot find a problem. *ak | |||
| 01/31/1998 | |||
| Consumer experiencing ongoing problem with vehicle abs braking system during wet weather. vehicle has been in/out of dealer shop on three occasions, and problem cannot solved. dealer informed consumer that they cannot find the problem. *ak | |||
| 11/30/1998 | |||
| The consumer has been experiencing problems with anti-lock brake system. when applied the brakes, foot went to the floorboard. the manufacturer has been contacted. *ak | |||
| 08/01/1998 | 1 | 02/01/1998 | |
| Anti lock brakes locked up resulting in vehicle collision. | |||
| 05/15/1998 | |||
| Consumer been experiencing intermittently/ongoing problem with vehicle braking system. condition occurred when road conditions were either damp/wet and at a rate of below 30 mph. brakes locked up, and vehicle rear ended sideways. dealer notified, and informed consumer that the problem could not be duplicated. *ak | |||
| 07/10/1998 | |||
| The abs braking system malfunctioned, causing the vehicle to slide through and extended stopping distance which resulted in an accident at 30 mph. the vehicle slid through and rearend another vehicle. upon impact, the driver's and passenger's airbags did not deploy. did not protect the occupant in this accident. dealer cannot determine problem. *ak | |||
| 05/19/1998 | 1 | 03/01/1998 | |
| Steering shaft failure. also, power door locks failed/abs brakes malfunctioned, causing brakes to vibrate upon braking. | |||
| 1 | 12/16/1997 | ||
| Anti lock brakes not working properly, extended stopping distance. | |||
| 11/30/1997 | 2 | 10/30/1997 | |
| Anti-lock brakes failed several times, on one occasion accident resulted. | |||
| While driving the vehicle consumer tried to make a sudden stop by depressing the brake pedal to the floorboard, the vehicle slowly came to a stop. consumer contacted dealer.*ak | |||
| SERVICE BRAKES, HYDRAULIC - ANTILOCK - ABS WARNING LIGHT | |||
| 03/10/2005 | 7600 | 3 | 02/01/1998 |
| At some point the cruise control on my 1998 ford f150 pick-up stopped working. as i seldom use it i'm not sure how long it was out. next the #13 fuse failed. the replacement fuse failed immediately. with this fault i was unable to get the truck out of park if started in park. the abs light was flashing and the brake lights did not work. took truck to earnhardt's ford dealer for repairs. they traced problem to shorted brake pressure safety switch and speed control servo. due to the defective brake switch the wiring harness was saturated with brake fluid. all three defective parts were replaced. these repairs cost $3,100 dollars. the mechanic (ken tueffel) stated i was very fortunate the truck did not catch fire. with the recent news reports on the ford pick-up cruise control brake pressure switch causing fires i believe ford motor company has known about the safety hazard of these switches for years and owe me a refund on these repairs.*ak | |||
| SERVICE BRAKES, HYDRAULIC - ANTILOCK - CONTROL UNIT/MODULE | |||
| 05/10/1999 | 1 | ||
| Anti lock brake sensor assembly shorted out causing light to illuminate. mjs | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS | |||
| 05/06/1999 | 9 | 05/27/1998 | |
| Consumer states that there is excessive wear of front brake rotors and pads. the rotors have been replaced on four occasions and the pads have been replaced on five occasions and the problem is reoccurring. the dealer has been contacted. *mj | |||
| 10/01/2001 | 1 | 02/18/1998 | |
| When appyling brakes, brake pad will rub against rotor, causing the rotors to warp. *ak consumer states while applying brakes, the front right wheel grabbed making a thumping noise causing the surface of the rotor to flake. the flaking chewed the brake pads excessively. rotors had to replaced. *tt | |||
| 1 | |||
| Intermittently when the brakes are applied pedal pulsates, resulting in extended stopping distance. dealer has changed pads and rotors. however, problem still exists. *ak slc | |||
| 03/09/2001 | 1 | 04/01/1998 | |
| Vehicle was in low gear, consumer tried to slow down, applied brakes and vehicle kept going. vehicle finally hit tree. neither airbag deployed. *ak the air bags failed to deploy during the accident. *yh | |||
| 1 | |||
| Consumer feels the back brakes do not stay adjusted and that the self-adjusters are poorly designed which will not keep brakes adjusted, this vehicle has almost caused accidents due to faulty brakes. *slc | |||
| 1 | |||
| Brake failure resulted in accident. yh | |||
| 1 | 03/01/1998 | ||
| Brakes are not large enough for the vehicle/failed, resulting in collision. | |||
| 06/11/1998 | |||
| When driving forward and backing up consumer applied the brakes, and noticed everytime applying the brakes there is a squeaking noise. *ak | |||
| 10/24/1998 | |||
| The rear braking system is inoperable which reduced the braking ability and caused an accident. dealer said it came from the factory with that problem, and there is no solution. cause unknown. please provide details. *ak | |||
| 02/02/1998 | 1 | 02/02/1998 | |
| Brakes experience extended stopping distances. | |||
| 07/21/1998 | 0 | ||
| Consumer said when he was driving his truck and started to put on brakes the brakes locked up on him. *ak | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC | |||
| 127000 | 1 | ||
| Consumer smelled a burning odor while driving at 45 mph. upon inspection of the vehicle consumer noticed that disc brake hub broke in the locked position. consumer was unable to get the part replaced because the manufacturer discontinued making the part. *ak | |||
| 09/19/2002 | 2 | 08/01/2098 | |
| On 14jun01 my truck had 20709 miles on it. charapp ford replaced the front brake pads and turned the rotors in order to pass the state inspection. this can be verified through invoice#20709. on 17jul02 my truck was inspected at murray's ford in dubois, pa with no problems, mileage 29978, invoice # c09529. on 19sep02 i had murray's check a rubbing sound from my front brakes. they found the brake pad was missing from the front right brakes resulting in metal to metal contact. this required new brake pads and new rotors. my truck had 31378 miles, invoice # c12269. i do not believe the brakes should have to be replaced with this low mileage considering i do not overload my truck nor do i tow at all. i believe there is a flaw in the design of the brakes, brake pads, or poor workmanship.*ak | |||
| 09/01/2002 | |||
| Brake pedal will go all the way to the floor. brakes are warped. dealership is aware of problem. *ak | |||
| 06/30/2002 | 2 | 08/01/2001 | |
| Front end brake and tie rod end problems from date of purchase. *ak | |||
| 3 | 01/01/1998 | ||
| When applying brakes front disc brakes locks up, creating extreme vibration which results in loss of steering control. *ak the left front wheel assembly gets hot. *yh | |||
| 04/17/1998 | 04/01/1998 | ||
| The dealer has addressed the brake issue by turning rotors/drums. 10,000 miles later im having the same problem, there seems to be a problem with braking equalization from front to rear. the rear brakes have yet to show signs of wear. overall the vehicle is running good but it appears the few on going problems are going to cost me after warranty is over.*ak | |||
| When applying the brakes on dry pavement back brakes grab, but the front brakes do not, causing extended stopping distance. at 22,000 miles the brake pads and rotors were replaced. at 28,000 miles the problem has returned. please provide any further details. *ak | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - CALIPER | |||
| 10/02/2003 | 66398 | 1 | 07/10/2001 |
| We have a 1998 ford f150 that was purchased in 2001 equipped with anti-lock brakes. yesterday they locked up prematurely while driving on the highway. it started with a burning metal smell & started to shake & vibrate. we couldn't go over 40 mph. it's quite fortunate that there was an auto repair shop on a nearby corner where we stopped, and discovered that the break pads were fine; however, the passenger side caliper was locked up. *la | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - PADS | |||
| 03/27/2001 | 1 | 08/01/2000 | |
| No warning of brake pads getting low. i took my truck to a mechanic because the front brakes were making a noise. he reported that my brake pads had worn completely away and had damaged the rotors to the point that they had to be replaced. the mechanic said that normally brake pads contained a squeaker device to let you know when the pads are getting low. my ford factory installed brake pads did not have this.*ak | |||
| 6 | 10/01/1998 | ||
| Brakes fail when depressed, then grab at last second. dealer performed a brake service consisting of grinding the metallic pads but problem is worse and brakes now groan upon stop. *ak | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - ROTOR | |||
| 05/17/2003 | 62441 | 1 | |
| The front left tie rod broke, which caused loss of steering. the vehicle was taken to the dealer for repairs. *ak *ts. the dealer replaced all 4 tie rods. the rotors were replaced which caused the vehicle to vibrate when the brakes were applied. *jb | |||
| 10/01/2001 | 1 | 02/18/1998 | |
| When appyling brakes, brake pad will rub against rotor, causing the rotors to warp. *ak consumer states while applying brakes, the front right wheel grabbed making a thumping noise causing the surface of the rotor to flake. the flaking chewed the brake pads excessively. rotors had to replaced. *tt | |||
| While having brakes serviced technician noticed corrosion on rotors. technician tried twice to remove corrosion off rotors,and corrosion could not be removed. dealer replaced rotors. please provide further information.*ak | |||
| 03/22/2001 | 0 | ||
| Consumer took car into dealer for a routine inspection, and dealer said brakes where wearing unevenly. there was more pressure on inside of rotors than on outside.*ak | |||
| Braking system malfunctioned due to a defective brake rotor which cause extended stopping distance. also had a recall for the throttle and the james hodge ford (1800-675-5447) claimed they did the recall repairs, and gave driver an invoice. banother ford dealer stated the previous deale r did not fix the part that was on recall which may have caused a crash. please provide further information. *ak | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM | |||
| 05/01/2099 | |||
| While driving at 60 mph on highway. the pin in the rear axile broke causing the axile to come completely out of the housing, hitting the side of pickup and then flew into open field. cars behind saw this happen and lucky it did not hit them. good control of pickup kept from having a rollover or going into oncoming traffic. dt | |||
| 08/15/1999 | 1 | 04/01/1998 | |
| No summary | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM - SHOES/LININGS | |||
| 06/06/1998 | |||
| When applying brakes during normal braking brakes locked up, causing the truck to slide. driver has lost control of the vehicle many times. this has happened during inclement weather ,aftet the truck has set for a while. problem was reported to the dealer. dealer stated that problem was due to the rear brake shoes and not the abs. problem has not been corrected. please provide any further information. *ak | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - HOSES, LINES/PIPING, AND FITTINGS | |||
| 07/19/2005 | 70000 | 1 | |
| 1. driving with my fiancee to go out to eat in evansville 2. loss of rear brakes(found out later a pinhole in brakeline) 3. damage front in due to traffic stop quickly and i could not, so i went offroad to avoid a car in a soybean field. to correct the failure i am not installing the recycled brake lines that i think was used when the f150 was made shouldn't they last more than 7 years since this is a safety for the driver,all passangers and other motorists, i have had a garage order stainless steel, and the front body parts. i don't know the cost of the bill yet..but i'm without my truck..for awhile. and a honey that has had a headache all day and a sprain wrist...hope it goes away(the headache). | |||
| 09/28/2002 | 1 | ||
| Consumer states that on the brake line there is a flat end that goes into the main braking system that supplies the brake fuel to the rear brakes.that flat end broke or wore off, resulting in brake fuel leaking out,causing no brake power. almost causing an accident. nlm | |||
| 02/13/2001 | |||
| While driving downhill at 30 mph, applied brake and pedal went to floor. consumer used emergency brake, and dropped to low 1 to slow vehicle down. it felt like a brake line leak. dealer replaced brake sensor. *ak | |||
| 07/14/1998 | 2 | 07/07/1998 | |
| Brake line failed twice. *yc | |||
| It appears that a fuel line on the rear driver's side near rear axle has a piece of rubber missing from it. the line runs near driver's rear brake line. *ak | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - MASTER CYLINDER | |||
| 10/18/2001 | 1 | 06/01/1998 | |
| Plastic piston in front disc brake assembly absorbs brake fluid, resulting in swelling of piston that causes the piston to freeze in the cylinder, rendering the brake system unusable.*ak | |||
| 05/03/1998 | 2 | 02/01/1998 | |
| Dealer would not repair trucks dual piston calipers/ wrong parts on truck. *ak | |||
| 12/07/1998 | 2 | 07/03/1998 | |
| Master cylinder failed. yh | |||
| 08/16/1998 | 3 | 02/01/1998 | |
| Brake master cylinder failed causing brake fading. mjs | |||
| SERVICE BRAKES, HYDRAULIC - PEDALS AND LINKAGES | |||
| 12/01/1997 | |||
| Brake pedal goes all the way to the floor. if your foot is not completely on the brake pedal, you will press the accelerator pedal. the dealer says this is normal and indeed other ford f150 s i have checked have the same problem. i have had two close calls because of this problem.*ak | |||
| When traveling upon& depressing the brake pedal, pedal goes passed the accelerator pedal, causing pedal misapplication and unwanted speed, resulting in near accident. consumer has contacted the dealer, dealer has yet to replace parts. please provide any further details. *ak | |||
| 12/07/1998 | 2 | 07/03/1998 | |
| Brake pedal is not firm and making noise like that of metal rubbing. yh | |||
| 10/24/1997 | |||
| Dealer replaced defective aluminum rim. braking pedal effort is excessive under normal conditions. applied brakes in wet conditions, vehicle failed to stop in time. | |||