Ford F250 1976
Model F250 made in 1976 by Ford got 3 recalls. There were some recalls concerningfuel system, gasoline, service brakes, hydraulic.
Model 1976
Recalls
| Campaign | Manufacturer | Manufacturing date | Type | # of units affected | Date Owner notified Mfg | Recall Initiated by | Manufacturers of recalled vehicles/products | Report Recieved Date | Record Creation Date | Regulation Part Number | FMVSS Number | |||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| FUEL SYSTEM, GASOLINE - DELIVERY - FUEL PUMP | ||||||||||||||||
| 07E064000 | FEDERAL-MOGUL CORPORATION | E (Equipment) | 34000 | 10/15/2007 | MFR | FORD MOTOR COMPANY | 08/27/2007 | 08/24/2007 | ||||||||
| Defect Summary | Certain federal-mogul aftermarket fuel pumps sold under the brand names of carter, accuflow, napa, truflow, parts depo, and parts master, shipped between august 2006 and july 2007 for use on the vehicles listed above. the fuel pump diaphragm in certain production runs may have been improperly installed or inadequately tested which may cause the fuel pump to leak. | |||||||||||||||
| Consequence Summary | A leaking fuel pump could create a vehicle fire hazard. | |||||||||||||||
| Corrective Summary | Federal-mogul will notify owners and replace the defective fuel pumps free of charge. the recall began on october 15, 2007. owners can contact federal-mogul at 248-354-7700. | |||||||||||||||
| Notes | This recall only pertains to aftermarket carter, napa, accuflow, tru flow, parts master, and parts depot brand fuel pumps and has no relation to any original equipment installed on the listed motor vehicles.customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov. | |||||||||||||||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - HOSES, LINES/PIPING, AND FITTINGS | ||||||||||||||||
| 76V078000 | FORD MOTOR COMPANY | V (Vehicle) | 10818 | 06/28/1976 | MFR | FORD MOTOR COMPANY | 06/01/1976 | 10/12/1979 | ||||||||
| Defect Summary | ||||||||||||||||
| Consequence Summary | ||||||||||||||||
| Corrective Summary | ||||||||||||||||
| Notes | Ford truck campaign no 196 4x4.light duty trucks.possibility trucks mayhave been produced with insufficient clearance between the brake masterscylinder primary or secondary outlet tube and the intermediate steering shaft.assembly methods resulted in deformation of the tube support bracket andmisassembly of the brake tubes to the inboard side of the tube support barcket.a bent support bracket in combination with inboard mounting of brake tubescould cause tube to contact the steering shaft and, eventually could result inwearing a hole in tube wall.should this occur, brake fluid and hydraulicpressure would be lost in either the front or rear portion of the dual brakesystem.the operator would be warned by brake light and an increase in brakepedal travel.(correct by inspecting and replacing tube that have been incontact with steering shaft.also, adjust clearance to be.75 inch or more). | |||||||||||||||
| SERVICE BRAKES, HYDRAULIC - POWER ASSIST | ||||||||||||||||
| 76V117000 | FORD MOTOR COMPANY | V (Vehicle) | 101 | 07/19/1976 | MFR | FORD MOTOR COMPANY | 02/27/1976 | 10/12/1979 | ||||||||
| Defect Summary | ||||||||||||||||
| Consequence Summary | ||||||||||||||||
| Corrective Summary | ||||||||||||||||
| Notes | Ford campaign no n/a.trucks.possibility that vehicles were assembled withimproperly installed shoulder bolt and attaching nut that secures the brakepedal to the master cylinder/vacuum booster pushrod.if this condition exists,the available bolt threads may not be enough to retain nut properly, and couldback-off permitting pushrod to separate from brake pedal.(correct byinspecting and replacing bolts and attaching nut and torqued tospecifications).light truck - pick-up. | |||||||||||||||