Recalls
Campaign | Manufacturer | Manufacturing date | Type | # of units affected | Date Owner notified Mfg | Recall Initiated by | Manufacturers of recalled vehicles/products | Report Recieved Date | Record Creation Date | Regulation Part Number | FMVSS Number | |||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
SERVICE BRAKES, AIR - DISC - ROTOR | ||||||||||||||||
98E010000 | AIMCO PRODUCTS INC. | E (Equipment) | 23500 | 04/15/1998 | MFR | FORD MOTOR COMPANY | 04/08/1998 | 04/09/1998 | ||||||||
Defect Summary | Equipment description: aftermarket brake rotors for use on certain ford and mazda trucks. cracked castings caused cracks to appear on the outer diameter of the rotor hat or around the stud hole. | |||||||||||||||
Consequence Summary | Loss of braking can result. | |||||||||||||||
Corrective Summary | Aimco will reimburse consumers/installers for the cost of replacement rotors and installation. consumers are requested to return to the location where the rotors were originally purchased/installed for replacement. | |||||||||||||||
Notes | Owner notification is expected to begin during april 1998.owners who do not receive the free rotors within a reasonable time should contact aimco at 815-759-7935.also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236). | |||||||||||||||
SERVICE BRAKES, HYDRAULIC - POWER ASSIST - HYDRAULIC | ||||||||||||||||
96V024001 | FORD MOTOR COMPANY | from 03/01/1991 to 11/01/1993 | V (Vehicle) | 108000 | 03/22/1996 | ODI | FORD MOTOR COMPANY | 02/05/1996 | 02/29/1996 | |||||||
Defect Summary | The studs which attach the brake master cylinder to the power brake vacuum booster assembly can develop stress corrosion cracking after being operated for an extended period of time in the southern california location. | |||||||||||||||
Consequence Summary | If a crack occurs, it could result in one or both studs fracturing. the master cylinder could then separate from the vacuum booster, when the brakes are applied, preventing the service brakes from activating increasing the risk of a vehicle accident. | |||||||||||||||
Corrective Summary | Dealers will replace the power brake vacuum booster assembly. | |||||||||||||||
Notes | System: brakes; power assist; primary; booster. vehicle description: multi-purpose vehicles and light duty trucks originally sold or currently registered in the southern california counties of los angeles, orange, san bernadino, san diego, riverside, ventura, santa barbara, san luis obispo, imperial, and kern.note: owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time, should contact ford at 1-800-392-3673. also contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393. |
Bulletins
Bulletin | Bulletin date | Replacement Bulletin | Item no. | Summary | Added |
---|---|---|---|---|---|
SERVICE BRAKES, AIR - CONTROLS | |||||
985A37 | 03/18/1998 | 601044 | The parking brake pedal may go to the foor with little or no effort during application. *yc | 06/23/1998 | |
SERVICE BRAKES, AIR - DISC - ROTOR | |||||
9845 | 03/02/1998 | 601264 | Availability of hub-mount brake rotor machining equipment. *yc | 07/15/1998 | |
SERVICE BRAKES, HYDRAULIC - ANTILOCK | |||||
985A22 | 03/18/1998 | 601025 | A comprehensive pull and drift diagnostic procedure has been developed to assist technicians with vehicle service. *yc | 06/19/1998 | |
95212 | 10/01/1995 | 46478 | The use of petroleum-based grease as a lubricant in servicing disc brakes is no longer acceptable because it may be incompatible with the rubber material used in the disc brake system. if petroleum-based grease is used to lubricate any par | 04/25/1996 | |
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS | |||||
99194 | 09/20/1999 | 6090082 | Information for servicing and diagnosing brake vibration, brake inspection, and brake friction material replacement. *tt | 03/06/2000 | |
985A36 | 03/18/1998 | 601043 | A grabbing and/or sticking condition during the first few brake applications when the brakes are cold or in the morning after an overnight rain may occur on some vehicles. *yc | 06/23/1998 | |
985A11 | 03/18/1998 | 601009 | Service tip information regarding elimination of sanding rotors and drums. *yc | 06/17/1998 | |
96222 | 10/21/1996 | 50941 | Brakes - elimination of sanding rotors and drums - service tip. *tw | 06/17/1997 | |
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC | |||||
985A13 | 03/18/1998 | 601012 | The use of petroleum-based grease as a lubricant in servicing disc brakes is no longer acceptable. *yc | 06/17/1998 | |
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - ROTOR | |||||
9814 | 01/19/1998 | 605562 | Subject regarding the availability of hub-mount brake rotor machining equipment. *tt | 07/09/1999 | |
985A5 | 03/18/1998 | 601003 | Hub-mount brake rotor machining equipment from rotunda is now approved for warranty and service use. *yc | 06/17/1998 | |
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM - SHOES/LININGS | |||||
BC0324972301 | 01/23/1997 | 51434 | Rear brakes grab when cold or damp. *jd | 06/27/1997 |
Investigations
NHTSA ID | Manufacturer | Date open | Date close | Subject | Recall campaign | |
---|---|---|---|---|---|---|
SERVICE BRAKES, HYDRAULIC | ||||||
EA95018 | FORD MOTOR COMPANY | 06/19/1995 | 04/02/1996 | SEPARATION OF MASTER CYLINDER | 96V024000 | |
Stress corrosion cracking (scc) occurs in studs used to secure brake master cyinder to power brake booster.due to scc, the studs fracture and master cylinder separates from booster.this results in sudden, unforeseen, and complete loss of braking. | ||||||
EA95018 | FORD MOTOR COMPANY | 06/19/1995 | 04/02/1996 | SEPARATION OF MASTER CYLINDER | 96V024001 | |
Stress corrosion cracking (scc) occurs in studs used to secure brake master cyinder to power brake booster.due to scc, the studs fracture and master cylinder separates from booster.this results in sudden, unforeseen, and complete loss of braking. | ||||||
EA95018 | FORD MOTOR COMPANY | 06/19/1995 | 04/02/1996 | SEPARATION OF MASTER CYLINDER | 96V024002 | |
Stress corrosion cracking (scc) occurs in studs used to secure brake master cyinder to power brake booster.due to scc, the studs fracture and master cylinder separates from booster.this results in sudden, unforeseen, and complete loss of braking. |
Consumer Complaints
Fail date | miles | occurences | Purchase date |
---|---|---|---|
SERVICE BRAKES, AIR - ANTILOCK | |||
10/01/1999 | 1 | 11/01/1994 | |
Traveling below the speed limit on dry pavement the brakes locked up causing the vehicle to skid and roll over. please contact john reutter at superior investigations if further information is needed. 727-848-3923. thank you john. | |||
SERVICE BRAKES, AIR - DISC - PADS | |||
06/15/1996 | 9 | 04/01/1996 | |
Have replaced front brake pads and rotors approx. every 9000 miles. pad crack causing shaking. have lost thre caliper pins that hold caliper in place. replaced calipers problem will not go away. shaking ha scaused ball joints to fail. ford denies any problems with the design of these brakes | |||
SERVICE BRAKES, HYDRAULIC | |||
01/01/2012 | 170669 | ||
I applied my brake paddle and it was fine one second and then lost pressure and went to the floor with a popping feeling on the right front wheel and then i turn my wheel into the other lane to avoid hitting the car in front of me and a car came from no where in the other direction and hit my 1994 ranger on the right rear wheel and bedside . | |||
08/17/2004 | 1 | ||
Received recall 96v024001 brakes: studs on hydraulic cylinder had broken. cylinder had separated causing the brakes to fail. *bf the failure caused an accident which resulted in $300 worth of damage. the consumer request reimbursement for the repairs. *nm | |||
12/01/1997 | |||
Vehicle brakes would lock up when applied at normal slowing speeds. | |||
SERVICE BRAKES, HYDRAULIC - ANTILOCK | |||
03/10/2000 | 2 | 11/01/2094 | |
The parking brake light and abs light come on after the truck has to make a hard stop and seems like the brakes don't work. also the lights stay on until the rbas valve is change. this has happen to me two times and this was very scarey when this happens. you don't know if you are going to stop the truck. dt | |||
05/19/2001 | 1 | 04/01/1995 | |
No summary listed for above vehicle. *ak | |||
07/17/1999 | |||
While driving on the road and approaching a stop sign, went to apply the brakes, and they would lock up and shimmy. *ak | |||
09/15/1999 | |||
On-going / intermittent problem with vehicle sliding whenever brakes are applied. problem occurs at low or high speed. vehicle being inspected by independent repair shop. dealer / m.anufacturer were not contacted at this time. *ak | |||
07/04/1999 | |||
Front passenger and driver fiber disc brake piston bent, causing, the brakes to lock up. dealer replaced both calipers with steel piston. please provide any further details. *ak | |||
03/22/1999 | 1 | 05/01/1997 | |
The anti-lock brakes(not sure if air or hydraulic) locked up, causing me to slide into the back of another vehicle. *ak | |||
12/30/1998 | 1 | 11/01/1994 | |
When i went to move my truck in the morning of december 30, 1998, the rear brake assembly completely locked up. i tried to rock it loose by shifting gears. i had to call a tow truck and they had to drag it onto the road in order to lift the rear, and neither rear broke loose while they drug it. the mechanic said the brake cylinders were completely rusted and all the rear brake hardware was replaced. in addition, i had to get a new clutch from trying to break the wheels free. the total bill was $1000.00 . i do not believe that a truck barely 4 years old should have had this problem. luckily, the brakes did not lock up while i was driving the truck. *ak | |||
01/22/1996 | 20 | 01/22/1996 | |
Abs brakes lock up during wet conditions. | |||
01/22/1996 | |||
In wet conditions while applying brakes the rear brakes lock up, resulting extended stopping distance. *ak | |||
01/23/1995 | |||
Brakes locked up and vehicle skidded when the roads were wet.this only happened in wet weather, in dry there is no problem. *ak | |||
11/01/1996 | |||
Abs brake failure, when driving at any speed and brakes are applied vehicle pulls and pedal pulsates and brakes grind. *ak | |||
1 | |||
While dfiving, experienced intermittent abs failure, when vehicle been sitting overnight, any surface rear brakes rubbed against wheels, then locked up, no prior warning.*ak *slc | |||
07/09/1996 | |||
When touching the brakes the wheels lock up for no reason. the truck has abs. please describe. *ak | |||
02/12/1996 | 2 | ||
Abs system failed, causing accident. *sd | |||
04/15/1996 | |||
Rear abs brakes lock up during rainy conditions. *ak | |||
Vehicles rear abs braking system grabs and lock-up when there is moisture in the air.due to defective material in brake lining.dlr can not do anything about it | |||
11/01/1994 | 30 | 07/22/1994 | |
Experience intermittent brake failure, abs equipped, when make attempt to slow down, brake pedal goes to floor, without prior warning. tt passenger suffered injuries.*jb | |||
Abs brakes locks sometimes then at time it does not stop you at all. tt | |||
07/21/1995 | 1 | ||
Brakes system failure, brakes lock up and drag, loss of braking. tt | |||
05/15/1995 | 1 | ||
Rear abs braking system malfunctioned and had rear wheel lock-up. tt | |||
03/27/1995 | 10 | ||
Rear abs brakes lock up when driving during wet/damp conditions. tt | |||
03/17/1995 | |||
Brakes failed, equipped with rear abs system. tt | |||
03/14/1995 | |||
Rear brake failure, equipped with abs system in the rear brakes. tt | |||
1) clutch assembly has faulty spring that hangs until breaking. gears failed to respond grinding gears. 2) abs brakes when applying brakes, pedal goes to floor. | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS | |||
09/27/2002 | |||
While driving at 40 mph the vehicle front right brakes locked up. consumer had vehicle towed to the dealership and they indicated that the brake calipers had seized up. this cause damage to the brake rotors, drums and pads. the dealership indicated that this is a common problem with these vehicle but they are not recalling them. ts | |||
01/01/1999 | 1 | 01/28/1998 | |
On several occasions brake system locked up, causing vehicle to skid. *yc | |||
1 | |||
Brake problems. | |||
03/30/1995 | 5 | 12/01/1993 | |
Brakes lock up intermittantly. | |||
12/01/1995 | 1 | 05/30/1994 | |
Brakes failed after recall repair. | |||
01/10/1996 | |||
While driving the brakes all of an sudden locks up. that is an very unsafe safety defect to the driver or any one else. | |||
While driving, experienced intermittent brake failure when brake action seems ineffective, continues to roll forward, causing extended stopping distance. *ak | |||
11/14/1995 | 4 | ||
Brakes pull to the right/left. *sd | |||
05/18/1995 | 8 | ||
Brake problems, causing vehicle to pull to left/right. *ak | |||
01/23/1995 | 3 | ||
Brakes grab intermittently. *tw | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC | |||
11/01/2001 | 1 | 11/01/2001 | |
Contacted ford motor company, phil long. *ak | |||
03/14/2000 | 4 | 02/01/1997 | |
No summary listed for above vehicle. *ak | |||
01/01/1994 | |||
Brakes lock-up when cold or wet | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - CALIPER | |||
01/05/2003 | 0 | 02/10/1994 | |
I was checking for recalls on my 1994 ford ranger and was surprised at how many recalls. the reason being that, my family has owned this vehicle since february 1994, we've only received the firestone recall notice. ironically, i have had and still have some of the listed components that were recalled as well as as some unlisted components since 1996, these problems have cost my family any where between $1000.00 - $2000.00, every year just in repairs alone. the vehicle barely has 147,000 miles on it and is only used to commute to anf from work, and occassional drives to l.a. county. see list below.... 07/2002 - vehicle overheated returning home from l.a. county, cracked cylinder head - cost $1200.00 02/2002 - brought vehicle in for oil change & alignment, and found the brake system and fuel system were bad, replaced brake rotors, calipers, gaskets, seals, and hoses were leaking, the fuel system was leaking and to this day, i still smell gasoline everytime i park . cost - $950.00 07/2001 - brought vehicle in for tires, and find the radiator not working, and the cooling fan was cracked all the wasy around on every blade, had to replace radiator, fan assy and all hoses & clamps. - cost - $ 800.00 01/2001 - front brake disc rotors were bad, replaced - cost - $ 300.00 03/2000 - routine 30k service + vehicle would vibrate and shudder when braking, so rear brake rotors & drums were surfaced and/or replaced, + replaced the following gaskets, seals, & plugs because of major leaks; work by ford dealer, #fotz6710c oil pan gskt, intake manifold gskt & valve cover gskt, #f5tz9439a manif. gskt, #f87z6584aa cover valve rocker arm gskt, thermostatic insert, , valves, oil filter, and thermostat - cost - $ 1425.00 see what i mean... | |||
I was coming from port author texas, and when i was about 1 or 2 miles from my house the right front wheel locked up. the caliper that works the brake came out and locked the wheel up. i was traveling at 55mph when it locked up, and i did not apply my brake for it to happen. i realize my truck is a 1994 model, however, the issue i'am trying to stress is this; i only have 15,000 miles, and drive it very little. my vehicle does not have the wear and tear for this to have happened! i feel it is a factory defect, and i should not be responsible for the repair. i am requesting an investigation into this matter before someone gets killed, and a remibursment for the repair cost i have already made. point to mention: if it was not a defect, then why did the ford motor company change the front left calipers. *ak | |||
07/04/1999 | |||
Front passenger and driver fiber disc brake piston bent, causing, the brakes to lock up. dealer replaced both calipers with steel piston. please provide any further details. *ak | |||
04/01/1995 | 1 | ||
Right caliper froze up, causing loss of effectiveness while driving. tt | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - PADS | |||
01/04/1999 | |||
While driving at 30 mph the brake pads fell off the vehicle which damaged the rotors and other parts on the vehicle. *ak | |||
7 | |||
When brakes are applied there is unknown grinding noise. also, numerous parts have been replaced, such as pads, etc., but problem remains. cause unknown. *ak | |||
08/17/1994 | 1 | ||
Replaced front brake pads. *ak | |||
Pads and rotors wear prematurely. tt | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - ROTOR | |||
01/05/2003 | 0 | 02/10/1994 | |
I was checking for recalls on my 1994 ford ranger and was surprised at how many recalls. the reason being that, my family has owned this vehicle since february 1994, we've only received the firestone recall notice. ironically, i have had and still have some of the listed components that were recalled as well as as some unlisted components since 1996, these problems have cost my family any where between $1000.00 - $2000.00, every year just in repairs alone. the vehicle barely has 147,000 miles on it and is only used to commute to anf from work, and occassional drives to l.a. county. see list below.... 07/2002 - vehicle overheated returning home from l.a. county, cracked cylinder head - cost $1200.00 02/2002 - brought vehicle in for oil change & alignment, and found the brake system and fuel system were bad, replaced brake rotors, calipers, gaskets, seals, and hoses were leaking, the fuel system was leaking and to this day, i still smell gasoline everytime i park . cost - $950.00 07/2001 - brought vehicle in for tires, and find the radiator not working, and the cooling fan was cracked all the wasy around on every blade, had to replace radiator, fan assy and all hoses & clamps. - cost - $ 800.00 01/2001 - front brake disc rotors were bad, replaced - cost - $ 300.00 03/2000 - routine 30k service + vehicle would vibrate and shudder when braking, so rear brake rotors & drums were surfaced and/or replaced, + replaced the following gaskets, seals, & plugs because of major leaks; work by ford dealer, #fotz6710c oil pan gskt, intake manifold gskt & valve cover gskt, #f5tz9439a manif. gskt, #f87z6584aa cover valve rocker arm gskt, thermostatic insert, , valves, oil filter, and thermostat - cost - $ 1425.00 see what i mean... | |||
05/01/2000 | 2 | 11/01/1993 | |
The truck is a 1994 ranger. it presently has 37000 miles on it . both front rotorsdeveloped cracks . a thumping occurred when applying the brakes . i had a mechanic look at it . he showed me the cracks in the rotors . i had it fixed . the rotorss cost me 118. dollars . this failure seems premature to me . i don't drive many miles during the year so it didn,t show up during the warranty period. i only drive about 7000 miles a year . do i have a recourse or do i just pay it and shut up ? thank you lloyd. *ak | |||
03/27/1995 | 7 | ||
Front rotors warped, causing brakes to pulsate. | |||
11/15/1994 | 5 | ||
Brakes serviced 4 times due to vibration/pulling when braking, also rear brakes squeak. *skd | |||
Pads and rotors wear prematurely. tt | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM | |||
05/14/2004 | 13400 | 2 | |
While making right hand turns consumer heard a loud grinding noise coming from the rear brakes. dealership repaired the problem once, but it did not resolve the problem. *ak | |||
03/30/1995 | 1 | 12/01/1993 | |
Brake shoes failed. | |||
1 | |||
While dfiving, experienced intermittent abs failure, when vehicle been sitting overnight, any surface rear brakes rubbed against wheels, then locked up, no prior warning.*ak *slc | |||
12/01/1994 | |||
Rear brakes are locking up. tt | |||
Involved (2) accidents with cause not clear w/rear locking and brakes not activating. please describe details. tt | |||
Lost brakes while driving twice=back wheels lock. tt | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM - DRUM | |||
07/21/1995 | 1 | ||
Replaced rear brake shoes/drums. *ak | |||
03/27/1995 | 7 | ||
Rear drums turned/replaced several times due to being warped. | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - HOSES, LINES/PIPING, AND FITTINGS | |||
01/05/2003 | 0 | 02/10/1994 | |
I was checking for recalls on my 1994 ford ranger and was surprised at how many recalls. the reason being that, my family has owned this vehicle since february 1994, we've only received the firestone recall notice. ironically, i have had and still have some of the listed components that were recalled as well as as some unlisted components since 1996, these problems have cost my family any where between $1000.00 - $2000.00, every year just in repairs alone. the vehicle barely has 147,000 miles on it and is only used to commute to anf from work, and occassional drives to l.a. county. see list below.... 07/2002 - vehicle overheated returning home from l.a. county, cracked cylinder head - cost $1200.00 02/2002 - brought vehicle in for oil change & alignment, and found the brake system and fuel system were bad, replaced brake rotors, calipers, gaskets, seals, and hoses were leaking, the fuel system was leaking and to this day, i still smell gasoline everytime i park . cost - $950.00 07/2001 - brought vehicle in for tires, and find the radiator not working, and the cooling fan was cracked all the wasy around on every blade, had to replace radiator, fan assy and all hoses & clamps. - cost - $ 800.00 01/2001 - front brake disc rotors were bad, replaced - cost - $ 300.00 03/2000 - routine 30k service + vehicle would vibrate and shudder when braking, so rear brake rotors & drums were surfaced and/or replaced, + replaced the following gaskets, seals, & plugs because of major leaks; work by ford dealer, #fotz6710c oil pan gskt, intake manifold gskt & valve cover gskt, #f5tz9439a manif. gskt, #f87z6584aa cover valve rocker arm gskt, thermostatic insert, , valves, oil filter, and thermostat - cost - $ 1425.00 see what i mean... | |||
05/25/2001 | 1 | 09/01/1993 | |
Water drips through drain hole in bed onto left rear brake line. line rusted through and all brakes were lost. mechanic states this is common with ford rangers. i have the failed part.*ak | |||
04/01/1995 | 1 | ||
Abs, brake failure, rear brake line frozen/locked up on right side. tt | |||
05/01/1994 | 2 | ||
Brake lines failed twice. *skd | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - MASTER CYLINDER | |||
01/05/2003 | 0 | 02/10/1994 | |
I was checking for recalls on my 1994 ford ranger and was surprised at how many recalls. the reason being that, my family has owned this vehicle since february 1994, we've only received the firestone recall notice. ironically, i have had and still have some of the listed components that were recalled as well as as some unlisted components since 1996, these problems have cost my family any where between $1000.00 - $2000.00, every year just in repairs alone. the vehicle barely has 147,000 miles on it and is only used to commute to anf from work, and occassional drives to l.a. county. see list below.... 07/2002 - vehicle overheated returning home from l.a. county, cracked cylinder head - cost $1200.00 02/2002 - brought vehicle in for oil change & alignment, and found the brake system and fuel system were bad, replaced brake rotors, calipers, gaskets, seals, and hoses were leaking, the fuel system was leaking and to this day, i still smell gasoline everytime i park . cost - $950.00 07/2001 - brought vehicle in for tires, and find the radiator not working, and the cooling fan was cracked all the wasy around on every blade, had to replace radiator, fan assy and all hoses & clamps. - cost - $ 800.00 01/2001 - front brake disc rotors were bad, replaced - cost - $ 300.00 03/2000 - routine 30k service + vehicle would vibrate and shudder when braking, so rear brake rotors & drums were surfaced and/or replaced, + replaced the following gaskets, seals, & plugs because of major leaks; work by ford dealer, #fotz6710c oil pan gskt, intake manifold gskt & valve cover gskt, #f5tz9439a manif. gskt, #f87z6584aa cover valve rocker arm gskt, thermostatic insert, , valves, oil filter, and thermostat - cost - $ 1425.00 see what i mean... | |||
12/13/2000 | 1 | 06/01/1995 | |
Bolt broke between the vacuum booster and master cylinder. *ak | |||
3 | 06/01/1998 | ||
We've found there has been several recalls on the brakes, fuel, windows, ect. we would like to know if in fact any of these problems have ever been addressed, as we have never been notified, and marroone, and world ford have done brake jobs on this vehicle- noone ever mentioned these recalls to us, and i'll bet these problems were never fixed, and that is why we have to keep having this vehicle serviced for the same problems. how can we find out this information??? *ak | |||
The front fiber disc brake piston bent which causes the wheels to lock up. replaced both calipers with steel piston. please give any further details. *ak | |||
01/25/1999 | 3 | 09/01/1996 | |
Brake master cylinder failed prematurely because manufacturer does not remove the seam burr on plastic fluid reservoir, where it attaches to the master cylinder body. i replaced the master cylinder for the first time in july of 1998. last january i discovered the master cylinder leaking again, after i experienced a brake light coming on during turns. experience led me to believe that my brake fluid was low, it was. this evening, i replaced the master cylinder again. upon priming to cylinder, my friend discovered brake fluid seeping through the cylinder body and the reservoir. both master cylinders, brand new, from napa auto parts store in boise, id failed prematurely. *ak | |||
08/03/1998 | 1 | ||
Coming to a stop; heard a pop; had no brakes. hit a building. checked under hood & noticed master cylinder just hanging; no support. called dealer. was informed recall on vehicle's master cylinder studs (#96v024000 & 396v024001). took vehicle to dealer & left it. later was called informed no recalls for master cylinder. *ak | |||
1 | 03/01/1994 | ||
While driving experienced master cylinder bolt failure when bolt detached, brake pedal went to floor when backing up, causing him to hit wall with side view mirror. *ak *slc | |||
12/01/1995 | 1 | ||
Master cylinder leaks, causing excessive play in brake pedal. *dsh | |||
05/15/1995 | 1 | ||
Master cylinder leaking. *ak | |||
SERVICE BRAKES, HYDRAULIC - PEDALS AND LINKAGES | |||
04/09/1995 | |||
Brake pedal got hard, resulting in accident. tt | |||
SERVICE BRAKES, HYDRAULIC - POWER ASSIST | |||
12/13/2000 | 1 | 06/01/1995 | |
Bolt broke between the vacuum booster and master cylinder. *ak | |||
SERVICE BRAKES, HYDRAULIC - POWER ASSIST - HYDRAULIC | |||
05/30/1998 | 1 | ||
Vehicle experienced failure of the recall component prior to recall notice causing extensive damage to other brake components, however reimbursement was only for booster unit not the other components. (96v-024) mjs | |||
1 | 01/28/1998 | ||
Brake lock up and skid while driving prior to recall notice or repair (96v-024). mjs | |||
SERVICE BRAKES, HYDRAULIC - POWER ASSIST - VACUUM | |||
01/01/2001 | |||
Vehicle experienced exact symptons as stated in recall 96v024001/ studs began cracking to power brake vaccum booster assembly. manufacturer has advised consumer that this vehicle was not a part of recall due to vin.*ak | |||
01/06/1995 | |||
Brakes: hydraulic power assist:booster failure. *ak | |||
SERVICE BRAKES, HYDRAULIC - SWITCHES - BRAKE LIGHT | |||
Brake switch failed, causing brake lights not to come on. switch is some how connected to cruise control. when brakes are applied to disengage cruise control, it will engage when brakes are let go. dealer has been contacted. *ak | |||
While driving brake switch malfunctioned, when upon braking, causes brake light to stick in/off position, resultingin near accidents. *ak |