Bulletins


BulletinBulletin dateReplacement BulletinItem no.SummaryAdded
SERVICE BRAKES, HYDRAULIC - ANTILOCK
985A603/18/1998601004Some vehicles may cycle when brakes are applied on rough roads or on an incline while making a sharp turn. *yc12/14/2000
9521210/01/199546478The use of petroleum-based grease as a lubricant in servicing disc brakes is no longer acceptable because it may be incompatible with the rubber material used in the disc brake system. if petroleum-based grease is used to lubricate any par04/25/1996
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC
985A1303/18/1998601012The use of petroleum-based grease as a lubricant in servicing disc brakes is no longer acceptable. *yc06/17/1998
956203/01/199539900Roughness concern during brake application. *tw11/01/1995
RCL/94E5503/01/19953013100Unknown11/01/1995
SERVICE BRAKES, HYDRAULIC - SWITCHES - BRAKE LIGHT
0217609/02/200210008580Lamp-brake-invadvertent disabling of brake shift interlock. *mj08/05/2004

Consumer Complaints


Fail datemilesoccurencesPurchase date
SERVICE BRAKES, AIR - ANTILOCK
08/24/1994110/01/1991
 Anti- lock brake light comes on at all times.
SERVICE BRAKES, AIR - DISC - CALIPER
06/22/1994510/14/1994
 Calipers and rotors failed numerous times.
04/22/199606/01/1992
 Vehicle brakes failed at 45,000 and 72,000 miles, due to seized rear calipers.
SERVICE BRAKES, AIR - DISC - PADS
308/01/1992
 Brake pads and linings fail intermittently.
SERVICE BRAKES, AIR - DISC - ROTOR
06/22/1994510/14/1994
 Calipers and rotors failed numerous times.
SERVICE BRAKES, AIR - DRUM - SHOES/LININGS
308/01/1992
 Brake pads and linings fail intermittently.
SERVICE BRAKES, AIR - SUPPLY - HOSES, LINES/PIPING, AND FITTINGS
01/08/1997203/01/1992
 The brake power assist is inoperative. there is a plastic fitting that connects 3 pieces of rubber tubing & these rubber tubings connect engine vaccuum to the power brakes. the plastic fitting breaks in cold wheather because of the vibration of the engine and car body. *ak
SERVICE BRAKES, HYDRAULIC
09/12/20031
 While driving about 65 mph on the highway applying the brake the pedal went all the way down to the floor. this caused the vehicle to stall and another vehicle hit the consumer from behind. the driver and passenger was transported by ambulance. there were no fatalities. please provide details. *ph
SERVICE BRAKES, HYDRAULIC - ANTILOCK
02/23/20010
 When putting on brakes vehicle pulls to right, and makes a grinding noise. took vehicle to dealer, and it was motor mounts. *ak
01/23/2001
 While driving 70mph with cruise control abs brakes became stuck. brake assist failed. brakes were smoking. cruise control failed to disengage. check engine light came on. engine would rev very high. disconnected cruise control cable to throttle. *ak
02/01/2000
 Abs will apply by themselves. brake pedal will have full hydraulic pressure while the vehicle is in braking motion. pushing real hard will release the pressure. problem is intermittent. dealer has tried to find the problem, but can't remdy one.*ak
 After starting vehicle suddenly accelerated. applied brakes and emgerncy parking brake, which did stop vehicle . brake pedal went to the floor. to gain control of vehicle consumer turned it off. dealer replaced power booster which did not correct the problem. please give any further details. *ak
01/15/2000
 Was driving approximately 45mph with cruise control on. started to slow down by applying brakes. vehicle failed to slow down. tapped brakes harder & nothing happened. reapplied brakes & vehicle proceeded to speed up. shifted into lower gear & vehicle was slowed down & applied the brakes to stop vehicle. *ak
 Leaks develop in the seals within the abs hydraulic control unit, causing brake fluid to leak, resulting in braking failure. please give any further details. *ak
103/01/1992
 Anti-lock brakes froze.
08/12/1997006/30/1992
 Driving 40mph & heard grinding noise when brakes applied. happens periodically. at dealer & mechanic took for test drive. did not hear anything. took brakes apart & noticed one side needed replacing & changed pads & rotors on other side. *ak
01/13/19971
 Antilock brakes grab.
11/01/1996
 Abs brake failure, when brakes are applied, they pulsate and cause vibration after driving for a period of time, *ak
05/01/1996705/25/1992
 Experienced intermittent abs failure from dead stop when accelerating at intersection, front brakes won't release, equipped with 4 wheel abs. *ak there is a tsb regarding this problem, the fix is a brake booster. *slc
07/01/19961012/14/1991
 Brakes overheat and smell like burning and pedal becomes very hard, consumer states this is referred to as phantom vacuum obstruction, brakes still work, however vehicle will only accelerate up to about 45 mph. *slc
 Abs brakes; sometimes after applying the brakes, the brake pedal does not come back to normal position. please describe. *ak
02/01/19951
 Brake pedal goes to floor in emergency situations, abs does not pulsate as it is supposed to. *dsh
01/19/1996
 The brakes stick or come out with no warning,this problem might be caused by the abs system.please describe. tt
06/01/19951
 Abs, brake failure, abs pumps kicks in when driving cause sticking while driving have to pull brake pedal up. tt
05/26/1995
 Abs system failure, floating calipers were binding, needed overhaul of rear brakes. tt
06/01/19951
 Abs brakes lock up, resulting in failure to release when applied on highway. *ak
02/10/1995
 Faulty abs module when brake pedal is touched it immediately stops. please explain. tt
SERVICE BRAKES, HYDRAULIC - FLUID
101/01/1992
 Brake fluid leak.
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS
03/12/20021
 Consumer states recall repairs were done, however on one occasion while driving consumer could hear a crunching noise and was told that the front subframe bolts were bad, consumer was informed that because of the recall with the rear bolts being bad it caused stress to the front since the frame is all one piece, ford stated that this was not part of the recall and repairs would be at the consumers expense. brakes were replaced. front wheel bearings were replaced. *slc
12/05/19991
 While starting vehicle white smoke was coming out of tailpipe. heard popping noise, also water and antifreeze was coming from tailpipe. took vehicle to dealer, and dealer indicated engine head gaskets were blown.*ak blower fan blade had to be replaced. on several occasions, the starter had to be replaced. customer states temperature gauge goes up, low on water and loosing coolant. dealer replaced radiator, water pump and serpentine belt. brakes are grinding. dealer replaced front brakes had turned rotors. on one occasion, the throttle positioning sensor had to be replaced. *tt
103/04/1998
 The front brakes failed due to the calipers locking up on the right side and cause vibration, the consumer had to replace the front brake calipers, rotors and shoes 8 times since purchased, one rotor on the right became so hot that it cracked the right front rotor. nlm
06/06/2000107/21/1997
 Engine head gaskets blew out, causing coolant to leak onto the engine. dealer has been notified. *ak brake system totally rebuilt at 52,453, motor mounts and transmission mounts replaced at 35,771, transmission rebuilt at 62,188 miles. *yh
09/16/1994310/01/1991
 Brakes lock up.
06/08/19958
 Brakes fail intermittently.
01/01/19921
 Brakes are defective. tt
12/05/1995
 While driving, lost engine power; difficult steering/braking; low speed; wire that supplies power to eec/fuel pump broke. tt
11/12/19912
 Brake cable harness loosened and wrapped around steering wheel, causing brakes to fade/steering difficulty. *skd
06/16/19951
 Brakes have to be changed every 15,000 miles, car vibrates when brakes are applied. tt
12/09/19941
 Front/rear brakes overheated/failed, causing hubcaps to overheat/burn. *skd
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC
06/14/2005154553706/14/2005
 Dt: 1992 ford taurus. the u shaped housing that holds up the engine rusted. consumer took vehicle to a mechanic, and they told him that it was an unsafe vehicle. the right outer tie rod, engine cradle rusted. also, the front, emergency, service and rear brakes were no good, the key broken in the ignition. there were other problems with the vehicle. the consumer acquired vehicle from an auction house. he had a mechanic inspect it, and found it was bad. he took it back the auction house and he kept the title. consumer believed that they might have tampered with the odometer . the incident date he took it to the mechanic and he rejected the vehicle. it was taken back to capital auction 603-622-9058.*ak
12/05/19991
 While starting vehicle white smoke was coming out of tailpipe. heard popping noise, also water and antifreeze was coming from tailpipe. took vehicle to dealer, and dealer indicated engine head gaskets were blown.*ak blower fan blade had to be replaced. on several occasions, the starter had to be replaced. customer states temperature gauge goes up, low on water and loosing coolant. dealer replaced radiator, water pump and serpentine belt. brakes are grinding. dealer replaced front brakes had turned rotors. on one occasion, the throttle positioning sensor had to be replaced. *tt
01/12/2002112/01/2001
 For a car with such low mileage, have had to replace or fix significant number items (serious safety items included!!) that failed. hope manufacturer can help reimburse costs. per research, these items should not break down at this mileage level! no safety defect mentioned. *ak
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - CALIPER
09/05/1995202/01/1994
 Brake calipers failed twice.
09/17/1996110/01/1991
 Capliper assembly replaced.
101/01/1992
 Brake calipers cracked.
09/01/19961
 Left front caliper seized, causing premature disc pad failure/scoring of rotors, also rust appears in brake reservoir.
10/10/1996
 Failure on the brake rotors, pads, and calipers, the brake pads, rotors and calipers needed to be replaced too often. *ak
05/05/1995
 Excessive wear of front brake rotors. problem occurs every two thousand miles.*ak
 The front inside caliper lock up. tt
02/01/19951
 Brake calipers failed/replaced twice.
11/01/19941
 Brake calipers stick, causing premature wear on rotors and pads. *skd
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - PADS
08/21/1998103/01/1995
 Transaxle will not engage after coming to a stop. l/f brake pad stays partially engaged resulting in premature wearing of said pad; luckily, i was coming to a slow stop when it gave out completely. this problem was not analyzed until my second front brake job within 25 0r so months. with wipers in use, activating the turn signal in either direction causes the wipers to stop.this tends to bring on a slight sense of panic during a heavy rain. lights go off without warning. this switch has been replaced twice at my expenseas have all other before mentioned problems except the wiper issue. i have been unemployed for 4 months and can't afford fixing this inconvenience. *ak
09/05/1995102/01/1994
 Brake pads failed.
04/01/1992
 Warped front brake rotors, causing brakes to pulsate. also replaced front brake pads. *ak
08/12/1997006/30/1992
 Driving 40mph & heard grinding noise when brakes applied. happens periodically. at dealer & mechanic took for test drive. did not hear anything. took brakes apart & noticed one side needed replacing & changed pads & rotors on other side. *ak
08/19/19931
 Vehicle vibrates when braking, due to front rotors/pads, and rear drums.
10/10/1996
 Failure on the brake rotors, pads, and calipers, the brake pads, rotors and calipers needed to be replaced too often. *ak
01/21/1993511/01/1992
 When you apply force to the brake pedal the steering wheel shakes, replaced front brake rotors/pads. *ak
04/27/19957
 Premature brake wear. *tw
06/01/19951
 Replaced pads. *ak
02/01/19951
 Brake pads failed/replaced twice.
02/15/1995
 Brake failure, excessive wear of brake pads. tt
 Brakes were grinding, had to have brake system replaced three times. pads wear prematurely. tt
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - ROTOR
 When brakes are applied would make grinding noises, like metal against metal. rotors were very bad. had deep grooves in them. cords were coming completely through & out of tires. also, ball bears are wearing out.
08/07/1992
 Premature wear of front brake rotors, causing vehicle to shake upon application of brakes. *ak
09/05/1995102/01/1994
 Brake rotors failed.
09/17/1996110/01/1991
 Rear brake rotors need to be replaced.
04/01/1992
 Warped front brake rotors, causing brakes to pulsate. also replaced front brake pads. *ak
08/12/1997006/30/1992
 Driving 40mph & heard grinding noise when brakes applied. happens periodically. at dealer & mechanic took for test drive. did not hear anything. took brakes apart & noticed one side needed replacing & changed pads & rotors on other side. *ak
101/01/1992
 Brake rotors cut due to cracked calipers.
08/19/19931
 Vehicle vibrates when braking, due to front rotors/pads, and rear drums.
10/10/1996
 Failure on the brake rotors, pads, and calipers, the brake pads, rotors and calipers needed to be replaced too often. *ak
01/21/1993511/01/1992
 When you apply force to the brake pedal the steering wheel shakes, replaced front brake rotors/pads. *ak
04/01/19941
 Front brake rotors caused vibration when brakes are applied. *sd
 Purchased car new three times, dealer replaced rotors three times and on the fourth time they were turned. *ak
06/09/19939
 Front brake rotors replaced due to squeak.
 Rotor was replaced at 29,000 miles . tt
06/01/19951
 Replaced rotors. *ak
06/01/19953
 The rotors all over the car have had to be replaced every 10,000 miles. the car has abs system. the rotors have all been warped. tt
02/01/19951
 Front brake rotors failed/replaced twice. *skd
07/14/19941
 Premautre brake rotor failure. *skd
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM
06/14/2005154553706/14/2005
 Dt: 1992 ford taurus. the u shaped housing that holds up the engine rusted. consumer took vehicle to a mechanic, and they told him that it was an unsafe vehicle. the right outer tie rod, engine cradle rusted. also, the front, emergency, service and rear brakes were no good, the key broken in the ignition. there were other problems with the vehicle. the consumer acquired vehicle from an auction house. he had a mechanic inspect it, and found it was bad. he took it back the auction house and he kept the title. consumer believed that they might have tampered with the odometer . the incident date he took it to the mechanic and he rejected the vehicle. it was taken back to capital auction 603-622-9058.*ak
07/16/1996103/01/1992
 Brake shoe replaced due to steering wheel shimmying.
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM - DRUM
103/12/1992
 Drums failed.
08/19/19931
 Vehicle vibrates when braking, due to front rotors/pads, and rear drums.
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - HOSES, LINES/PIPING, AND FITTINGS
06/01/2000303/01/2000
 My rear brake system keeps coming apart. this first happened while driving at 55 m.p.h. and i had to brake suddenly. i had to drive around vehicle in front of me to avoud a crash, i had a mechanic put them back together but the problem keeps persisting even though i have had the brake system completely redone. the problem with my cruise control is that when i use it and set it the car will go that speed and after a while will increase the speed on it's own.i have almost gotten a ticket because of this and since everytime i use it this happens i have stopped using the cruise control.*ak
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - MASTER CYLINDER
10/24/2000111/01/1998
 No summary listed for above vehicle. *ak
11/01/1992
 Experienced a complete failure of brakes when stopping at an intersection. brake pedal went all the way to floor with car failing to stop. brakes later reactivated as car was backed up. there was no loss of brake fluid. dealer repaired brakes by replacing master cylinder ,but was unable to explain why there was a complete failure of the brakes and the fact that the brakes later reactivated. *ask
SERVICE BRAKES, HYDRAULIC - PEDALS AND LINKAGES
03/06/1992
 Brake pedal does not release completely after short periods of stop and go traffic. tapping pedal released hold.
SERVICE BRAKES, HYDRAULIC - POWER ASSIST
07/15/2000303/01/1992
 Vacuum braking power assist has broken 3 times, resulting in loss of power braking. manual braking is next to impossible.*ak
07/01/19961012/14/1991
 Brakes overheat and smell like burning and pedal becomes very hard, consumer states this is referred to as phantom vacuum obstruction, brakes still work, however vehicle will only accelerate up to about 45 mph. *slc
SERVICE BRAKES, HYDRAULIC - POWER ASSIST - HYDRAULIC
 After starting vehicle suddenly accelerated. applied brakes and emgerncy parking brake, which did stop vehicle . brake pedal went to the floor. to gain control of vehicle consumer turned it off. dealer replaced power booster which did not correct the problem. please give any further details. *ak
SERVICE BRAKES, HYDRAULIC - POWER ASSIST - VACUUM
06/24/19961
 Defective brake booster.
05/01/1996705/25/1992
 Experienced intermittent abs failure from dead stop when accelerating at intersection, front brakes won't release, equipped with 4 wheel abs. *ak there is a tsb regarding this problem, the fix is a brake booster. *slc
06/01/19951
 Replaced brake booster. *ak
SERVICE BRAKES, HYDRAULIC - POWER ASSIST - VACUUM - HOSES, LINES/PIPING, AND FITTINGS
01/23/2001
 While driving 70mph with cruise control abs brakes became stuck. brake assist failed. brakes were smoking. cruise control failed to disengage. check engine light came on. engine would rev very high. disconnected cruise control cable to throttle. *ak
01/07/1999
 While driving and applying the brakes, about 90% of the braking power was lost. upon the checking the vehicle, a valve on the brake vacuum hose was cracked. owner was able to replace the valve. the dealer is not aware of the problem. *ak
01/03/19943
 Replaced power brake check valve due to brake pedal hardness. *sd