Gmc Suburban 1994 - Service brakes - car safety information, failing parts, recalls, bulletins, complaints

Gmc Suburban 1994

Recalls
Technical Service Bulletins
Defect investigations
Consumer Complaints

Recalls

Campaign	Manufacturer	Manufacturing date	Type	# of units affected	Date Owner notified Mfg	Recall Initiated by	Manufacturers of recalled vehicles/products	Report Recieved Date	Record Creation Date
SERVICE BRAKES, HYDRAULIC - PEDALS AND LINKAGES
01I006000	GENERAL MOTORS CORP.	from 03/01/1993 to 09/30/1994	I	255770	07/13/2001	ODI	GENERAL MOTORS CORP.	07/02/2001	07/19/2001
Defect Summary	This is not a safety recall in accordance with the safety act. however, it is deemed a safety improvement campaign by the agency. vehicle description: 1992-1994 chevrolet and gmc suburbans equipped with vacuum power-brake assist and ebc4 anti-lock brake (abs) modules. these vehicles exhibit poor brake system performance.
Consequence Summary	This could be attributed to brake pedal feel.
Corrective Summary	Dealers will install a new brake pedal pad. in addition, dealers will inspect the brake-booster output rod and replace it if necessary.
Notes	Gm has decided to conduct a service campaign to advise owners to have the brake pedal pad replaced on their vehicles.owners can contact chevrolet at 1-800-222-1020 or gmc at 1-800-462-8782, concerning this program.
SERVICE BRAKES, HYDRAULIC - SWITCHES - BRAKE LIGHT
99V025000	GENERAL MOTORS CORP.	from 03/01/1993 to 09/30/1994	V (Vehicle)	988587	04/12/1999	MFR	GENERAL MOTORS CORP.	02/05/1999	02/08/1999
Defect Summary	Vehicle description: pickup trucks, crew cabs, utility trucks and sport utility vehicles. these vehicles were built with the polarity of the wiring for the zero adjust brake switch reversed from what was specified on the switch drawing. with the reversed polarity, the contacts in the brake switch can wear out prematurely. the brake switch will perform normally until the brake switch contacts wear out, resulting in loss of the brake lamps without any warning to the driver.
Consequence Summary	This would fail to warn a following driver that the vehicle is braking and could lead to a crash.
Corrective Summary	Dealers will replace the brake switch and reverse the wiring.
Notes	Owner notification began april 12, 1999.owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chevrolet at 1-800-222-1020 or gmc at 1-800-462-8782.also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

Bulletins

Bulletin	Bulletin date	Replacement Bulletin	Item no.	Summary	Added
SERVICE BRAKES, HYDRAULIC
98865020A	09/01/1998	86-50-20	602774	Vehicles leading or pulling to either side while applying the brakes, and premature front brake wear, especially vehicles that have been used to tow a heavy load. *yc	01/13/1999
SERVICE BRAKES, HYDRAULIC - ANTILOCK
01125	06/29/2001		623419	Special policy bulletin regarding product enhancement brake system subjective feel / poor brake system performance. *tt	10/29/2001
01005	06/01/2001		623411	This special policy product enhancement covers vehicles equipped with vacuum power brake assist and ebc4 abs brake modules exhibitng poor brake system performance / brake system subjective feel. *tt	10/29/2001
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS
990524001A	09/01/1999	990524001	608388	Brake lead/pull and front brake wear. *mjs	11/26/1999
990524001	06/01/1999	865020A	606765	Some cab chassis, crew cab, and pickup models may exhibit a brake lead / pull and front brake wear. *tt	09/02/1999
98865020	04/01/1998		601128	Vehicle leading or pulling to either side while applying the brakes or front brake wear not meeting expectations. *yc	07/01/1998
SERVICE BRAKES, HYDRAULIC - POWER ASSIST
01005	06/29/2001		623509	Some vehicles equipped with vacuum power brake assist and ebc4 abs brake modules may comment that their vehicles exhibit poor brake system performance, this may be attributed to brake pedal feel. *slc	10/29/2001

Investigations

NHTSA ID	Manufacturer	Date open	Date close	Subject	Recall campaign
SERVICE BRAKES, HYDRAULIC
EA95026	GENERAL MOTORS CORP.	09/20/1995	09/20/2001	POOR BRAKE PERFORMANCE	01I006000
	Poor performance of abs brakes

Consumer Complaints

Fail date	miles	occurences	Purchase date
SERVICE BRAKES, AIR - ANTILOCK
11/22/1999		2
	The brakes failed on a wet rough surface. i did not have any brakes at all. this happened to my son in 1994 and i took the vehicle back to the dealer for inspection, and they said the brakes were ok. this last time when i went back to the dealer i was advised that gmc knew there was a problem but gmc did not notify the dealer's how to fix the problem. i called gmc at 1-800-462-8782 and spoke to audrey pressley and kevin, file #99289962 to know satisfaction about repairing the brake system. this vehicle has been very well maintained by the local gmc dealer. when the brakes failed i was very lucky to avoid an accident. it seems that the brakes fail on a wet bumpy surface. the rest of the time they are ok.
			03/01/1994
	Although no accidents, i've had several close calls when anti-lock brakes activate on bumpy roads when coming to a stop. i've come within inches of hitting a car in front of me when braking on rough pavement.*ak
03/12/1996		5	07/01/1994
	Brakes failed completely first occurance. partially failed, very hard stopping standing on brake pedal four subsequent occurances. i drive very carefully, braking long before i normally would since first occurance. this was a sizable investment. i would like at least the same braking confidence i experience in my 1940 la salle. please help. to date there has not been an accident. it is waiting to happen. thanks.
		8	04/01/1997
	The abs brake will disengage all brakes for a few seconds if breaking on any rough surface. this has caused near accidents. classic cheverolet checked the codes and break in february of this year. they found no codes and couln't get the brakes to fail. bp procare in richmond hts. also couldn't find any problems. the brakes are fine a flat surfaces but on a surface which causes rapid bumps it will not stop the vehicle. as you apply the brakes with the bump the abs sounds like it is active but the vehicle does not stop or slow for a few seconds. then they start to stop and work fairly well. i found this out on of the first days driving it. i came up to an intersection and the light changed so i should have stopped but couldn't and the vehicle went straight through without slowing.
			02/01/1996
	Anti lock brake failure.
SERVICE BRAKES, AIR - SUPPLY - HOSES, LINES/PIPING, AND FITTINGS
10/07/2003	98500	2	06/10/1997
	Had failure of both rear brake lines and fuel delivery lines/sending unit due to heavily rusted/ruptured metal lines. fortunately, the failures were observed in my driveway, leaking brake fluid and gasoline. the vehicle required towing to the local mechanics garage.total cost of repair (all rusted lines and fuel sending unit) at local garage was $875.00.*ak
SERVICE BRAKES, HYDRAULIC
09/15/2003	0
	Diesel k2500 suburban. injection pump suffered a problem with intermittent fuel cutout. solution was replacement of injection pump. repeated dealer attempts to diagnose exact problem was not successful. seat mount failed. this caused seat to tilt on base & torque remaining mounts. the wiper motor cut out at random. gm acknowledges this problem for other models, but not for mine. this would cause failure of motor functions (in my case, the wiper would not start if parked, but would start if pulled out of park position). brakes are the most interesting problem. while there may indeed be a problem with pedal suddenly going to the floor i think the actual situation in most of those cases may actually be as follows. i had to brake fairly hard in unexpected traffic, and the antilock brake system fired. i was moving not faster than about 50 mph at the time, but it took (measured) 642 feet to stop the vehicle. at no time did i release the antilock system before the vehicle stopped. during this time, i was able to steer quite successfully around two stopped vehicles, and to run up on a grassy shoulder and back onto the pavement. i had the front brakes relined and trued, and the fluid flushed and replaced, at a local shop shortly after purchasing the vehicle used (with about 56,000 miles). apparently, gm knows that it is necessary to cycle the antilock motor so that all the pistons are at the right position before bleeding the brakes. if the brakes are bled with the motor not centered, the effect is that full modulation of the brakes does not occur, for some or all wheels, when the antilock system fires. however, the dump-valve function relieves all brake pressure while the motor is running. the result is that only partial brake application is effectively being made -- this might be almost any arbitrary percentage of a 'normal' full brake application -- and this may greatly reduce the amount of deceleration seen in critical situations.
01/01/1996
	40 mph applied brake pedal to the floor and the brake did not engage. applied the brake and the vehicle stopped. this incident occurred three times jan, july, and sept. of 1996
SERVICE BRAKES, HYDRAULIC - ANTILOCK
04/01/1996		1	03/20/1996
	Dt: the contact states that he owns a 1994 gmc suburban. the contact is having problems with brakes. they are performing poorly. there are abs brakes on this vehicle, and this vehicle has done this ever since he purchased the vehicle. he has taken vehicle to the dealer and they would fix the problem for a little while, but it wouldn't last very long. the problem would continue to come back. also, there was a recall for this problem, but this vehicle was not included in the recall due to vin. *ak
05/10/2001		1	03/01/2001
	Original problem braking caused me to go into a cemetery (luckily to my knowledge the only thing that i hit was a curb which i went over on a diagonal) thru ongoing traffic luckily no one was injured but this may have caused the 2 wheels by centerline to fracture which later became apparent at different times. it is also possible that the 2 wheels were simply defective to start and decided to let go at different times. i surley would like to know if the wheels were defective from the get go.*ak
08/20/2000		1	04/01/1994
	While accelerating from a stop light a vehicle traveling from the opposite direction turned in front of my vehicle. i applied the brakes in a panic stop, probably the first time since the vehicle was new. the brakes immediately released and i coasted into the intersection. i swerved to miss the oncoming vehicle and did just miss it. since this incident the brake warning light has been steady on. i have disconnected the electrical connection at the anti-lock brake module. a general motors mechanic has pulled the codes and says that the anti-lock brake system has completely failed. i plan to go to a gmc dealer this month and complain until i get some satisfaction. the first time i needed my anti-lock brakes to function they failed. this is totally unaceptable. i see from this web site that there have been numerour complaints about the brakes on suburbans and wonder why there has never been a recall. *ak
05/25/2001		0
	Consumer was traveling about 70mph on highway and noticed that abs braking light was on, and there was a noise when abs braking system kicked in. dealership was aware of problem. *ak
02/25/2001
	Consumer was traveling 25mph on highway and brakes didn't grab at all. dealership was aware of problem. *ak
08/27/1997
	When applying brakes in an emergency/sudden stop on rough or wet surface abs will not engage. feel free to provide any further details on this matter. *ak
		2	06/01/1997
	Intermittently when brakes are applied pedal goes partially to floor, resulting in extended stopping distance. dealer has inspected vehicle, and could not duplicate or correct problem. ak because of faulty brakes, consumer has had 2 accidents, where one person was injured and several running of stop lights and stop signs. slc
12/20/1994		0
	When driving on a bumpy road or hitting a bump while braking at same time, brakes would not respond. consumer had rear ended another vehicle because of this problem. *ak

	When brake pedal is applied there is a delayed response. brakes will grab/ release, and, grab again. deaeler has been contacted. *ak
		3
	When appyling abs brakes pedal goes to the floor, causing extended stopping distance. cause unknown, dealer cannot identify the problem. ak front brakes are shuddering because front brakes are too small for the vehicle. yh
		2	05/01/1996
	On two(2) separate occassions, emergency application of the brakes at approximately 45 mph, failed to slow vehicle. in both cases, the pedal did go hard but the vehicle continued to travel as if the brakes had not been applied. in the first instance that occurred in 1997, i was able to steer around a car that had stopped suddenly in the lane in front of me and avoided a collison. following the incident, i was unable to duplicate the failure after repeated tries. the second occasion occured in feb. 1999 when my wife travelling at 45 mph was unable to stop for a vehicle that turned in front of her at an innersection striking the crossing vehicle in the passenger side. although the other driver was cited for the accident, my wife reported to me the same conditions that i had experienced previously and had not told her about. she refused to drive the vehicle for several months and only after i had taken the vehicle to the dealer and was told there was nothing wrong with it. i have been a licensed driver for over 35 years and have owned and driven many vehicles with and without antilock brakes. there is a problem with the brakes on this vehicle that has been experienced by other owners of similar vehicles i have spoken to over the years.
07/16/1999		0
	Roads were wet, towing 600 pounds, consumer tried to stop and vehicle will not stop. vehicle stopped in the middle of intersection. another time while driving in the rain, consumer need to stop at a very busy road, vehicle did not stop. consumer feels lucky there were no cars coming. took vehicle to dealer, and they daid it was the wheels.*ak

	I feel that my abs take a very long distance to stop my vehicle even at 25 mph, at which speed i had to swerved to avoid the vehicle in front of me. i e-mailed to gmc who told me that they where sorry about my problem and to bring my truck to a dealership to have it checked.i brought my vehicle to two different dealerships and their response was that my abs are working, i know that there was a recall on some other vehicle from gmc that describe exactely what i am feeling with my suburban.do you have any complaint from other owners of suburban? i talked to a few of them in my area and their response was that none of them like the way their abs work. *ak
01/01/2000		2	03/01/1994
	When applying brakes aggressively on dry pavement abs system hesitated before activating, causing extended stopping distance. cause unknown. ak ml
04/19/2000		1
	Abs failure caused accident. yh
01/15/1994
	Ea-95026: poor brake performance: vehicle experieced problem whenever it rolled over on rough surface, causing brake pedal to pulsate, and extended stopping distance. vehicle been inspected by independent repair shop. *ak
04/20/2000		20	06/01/1994
	I drove a gm product for over 20 years, before owning this machine, that weighed the same as this one, had the same size tires and type(factory reccommended) as my suburban and i never freewheeled through any red lights or hit anyone! it is very scary driving this machine. if the anti-lock brakes are so good then why are they automatically disconnected when in 4 wheel drive? i thought off road conditions and snow and ice(where 4 wheel drive is necessary) is where you would want the superior brakes?*ak
10/28/1999			06/01/1994
	When applying the brakes in an emergency, brakes grabbed and completely let go, causing driver to crash into vehicle ahead. this happened on a smooth road surface, and no inclement weather. dealership and manufacturer were notified about the problem. damages to the vehicle were repaired. nothing was done to the abs. ak ml
04/14/2000
	Consumer waiting at the intersection for light to change she applied brakes and the brakes didn't hold, and ran into the back of another vehicle. dealer stated abs system wasn't operable. *ak
08/07/1999			08/01/1994
	This condition is very serious when you are in need of your brakes the most they completly fail with no indication under normal brake use. please contact me for any usefull discription on what happened. i am a certified mechanic and have been trained in anti-lock brake service . *ak
01/19/2000
	While driving in the neighborhood, travelling about 20mph ,crossed an intersection, and vehicle two car lengths ahead stopped. also, vehicle in front of the consumer stopped. went to apply brakes and brakes failed. *ak
		1
	Rear anti lock brakes do not work properly and the front brakes lock up and slide due to design. *nlm
12/06/1999		5	02/01/1997
	No summary
11/28/1999		18	08/01/1998
	Non-repeatable, intermittent failure of abs reduces braking performance significantly to the point of loss of control

	When applying abs brakes on a slight incline and coming to a stop the brakes faile, causing extended stopping distance. cause unknown. please give any further details. *ak
11/19/1999		5	11/01/1998
	Thank god no one was injured i would like to get this problem fixed befrore any one does get hurt. no summary listed for above vehicle. *ak
11/20/1997			11/01/1993
	When brakes were applied in a panic stop, abs light came on and the pedal went to the floor, resulting in extended stopping distance. the dealer has replaced the abs brake module. *ak

	When applying the abs pedal goes to the floor,causing extended stopping distance. cause unknown. please give any further details. *ak

	When brake pedal is applied under normal or emergency conditions there is a decrease in stopping distance, on rough surface, there are no brakes at all whe vehicle goes into the anti-lock mode. also, when pedal is applied in a hard braking situation after the anti-skid system kicks in, pedal will release all the way to the floor. dealer has not been contacted. *ak
07/16/1999		1
	When applying the brakes during an emergency stop, truck starts to stop then begins to glide. this caused owner to crash into the rear of another vehicle. repairs have been made to the body of the truck. braking problem was not yet resolved. ak ml

	Intermittently when the brakes are applied the pedal goes to the floor, resulting in extended stopping distance. the dealer has been notified. *ak
07/24/1999
	When brakes are applied at 30mph and below under normal conditions, pedal goes to the floor, resulting in extended stopping distances, and once causing a minor collision. dealer and manufacturer have been notified. *ak
06/28/1998
	Whenever abs brakes are applied vehicle would fail to stop. this causes extended stopping distance. the problem is intermittent, but constant. taking to dealer. *ak

	While traveling and upon making any normal stop brakes disengaged for a period and kicked in, resulting in a minor rear end collision. consumer has contacted the dealer. please provide any further details. *ak
07/20/1999		10	11/01/1996
	I have reported this recurring abs failure before. while i see that a recall has been issued for many chevrolet and gm trucks,, i do not see my vehicle listed. why?
03/01/1995		2	10/01/1994
	When applying the brakes pedal goes to the floor, and vehicle only slows down and won't stop. owner has crashed twice. dealer said there was nothing wrong. ak ml

	Ea95026, poor brake performance; when applying the brakes and hitting any kind of road surface change, mainly potholes, truck would not brake for other 6 to 8 feet, depending on the speed of the truck. the problem has been reported the the dealership many times. the dealer was not able to find a problem with the system. please provide any other information. *ak
05/01/1994
	Ea 95026, abs braking system malfunctioned, causing extended stopping distance which may result in a crash. please provide further information. *ak
06/19/1999		2	06/01/1999
	I grow wary of the braking system daily. i plan to have the dealer look at the system.
01/06/1994		30	01/01/1994
	The anti lock brakes have failed on more than 30 occasions since the gmc 1500 surburban was purchased new. ailures are sporatic. in several instances the vehical went through intersections due to the brakes not activating despite applying normal brake pressure. the dealer has inspected the brakes on several occasions since new and has not been able to discover the cause of the problem. gmc haas been contacted several times but denys any issue with the brakes. the front drivers side and passenger side seat belts failed at with approximately 55,000 an 75,000 miles on the vehical respectivly. the spring /reel mechanism appeared to be broken in both instances causing the reel locking mechanism not to engage and allowing the seat belt to have slack during any driving situation eg seat belts would not tension during stopping or at rest.
06/10/1998		1	05/01/1995
	Anti-lock brakes failed on a wet surface causing me to skid into a van in front of me. damage to other party was approx. &2,500. anti-lock brakes on vehicle tend to disengage when braking on a bumpy surface which once caused me to skid into a skid.*ak
		3
	When applying the brakes, brake pedal went to the floor and vehicle did not stop. this has happened 3 times. dealer said it was normal. *ak
		5	01/01/1994
	Gm is recalling model years 1991-1996 suv and pick-ups for a problem with anti-lock brake systems. apparently this recall does not include suburbans manufactured during the same years. however, i am without doubt that the same problem exists in these suburbans. on at least 5 occasions, my suburban's brakes have failed when the vehicle moved from a surface with good traction to one with poor traction then back to good traction. each time, the stopping distance was greatly extended, resulting in my vehicle proceeding through intersections (stop signs). fortunately, in no case was oncoming traffic present or an accident would have resulted. repeated inspections of the brakes (but not the sensor switch, i presume) reveals no problems, but as an experienced driver i know the problem is very real. i highly recommend this recall be extended to suburbans. the conditions created by the antilock brake sensor switch are very dangerous. i plan to have this switch changed as soon as possible. *ak
08/15/1996
	Brake system does not work properly. whenever pedal is applied it goes lower to the floor then normal. vehicle inspected by dealer, and informed consumer that is the way it operates.. can nhtsa help in this matter. *ak

	When applying the abs brakes on dry pavement extended stopping distance occurs, cause unknown. this usually occurs when brakes are applied suddenly. the brakes seem to engage, disengage and then engage again. *ak

	When applying the brakes, pedal goes almost all the way to the floor, and the vehicle does not stop. dealer has not seen vehicle. *ak
05/01/1994		20	04/01/1994
	At various times, when the brakes are applied, they will momentarily fail to engage, causing the vehicle to move forward 10 to 30 feet, before the brakes take hold. i reported the problem to the dealer, without any action on their part. *ak
04/26/1999
	When brakes were applied on uneven pavement the pedal went to the floor, causing extended stopping distance, and resulting in a collision. the manufacturer has not been notified. *ak
10/19/1994
	When driving at any speed the brakes aren't working right. they are locking up and not stopping the vehicle all the time when the consumer is trying to stop. vehicle has been in repair shop five to six times, and the dealer still can't determine the problem. *ak
		1
	Anti lock brakes fail to re-grab fast enough when road is slippery.
			04/01/1997
	Abs brakes:driving at any various speed ,consumer will apply brakes, brake pedal will go to floor, causing loss of brakes. at times consumer will pump brakes or mash them hard, sometimes will regain brakes. this is a intermittent problem. dealer cannot find problem. *ak
04/04/1997
	When the brakes were applied the pedal went to the floor , the vehicle went into a skid, resulting in extended stopping distance, causing the vehicle to collide. the dealer hs been notified. *ak
10/10/1995			10/01/1994
	Abs brake problems; intermittently; on regular road condtions, during normal braking, it seems as though the brakes grab and don't release. gmc is not able to find a problem with the system. *ak
03/04/1994		15	01/29/1994
	Driving at 50mph, and coming to a stop sign, put foot on brake pedal and the truck didn't slow down. it went through the stop sign. had to pump the brake pedal several times before the truck would stop. *ak
06/07/1996		1
	Anti lock brakes failed resulting in vehicle collision.
11/01/1996		1
	Anti lock brakes failed causing loss of control.
		1
	Brakes fail continually resulting in lock up.
			02/08/1996
	Abs brakes fade and are non-responsive in an emergency situation. also, replaced front brake calipers/pads and rotors. *ak
01/01/1995		2	08/01/1994
	While attempting to stop, the vehicle failed to stop although the brake pedal was fully engaged. described as a complete loss of brakes, not the typical pumping felt with abs deployment.
07/10/1998		3
	When driving vehicle about 10 mph or less, stepped on the brake pedal to stop vehicle, but vehicle kept rolling for a few more feet away. manufacturer had been contacted. *ak
10/20/1995		3	11/20/1993
	Vehicle downshifts drastically, locks in a low gear and will not shift, abs comes on prematurely, and the cruise control will not work.
06/23/1998
	Consumer complaining of abs system failing to operate on dry/wet pavement,especially on rough road, abs makes unknown sound when applying the brakes. dealer notified and condition cannot be corrected. *ak
01/15/1994
	The abs system is not functioning properly, one brake will kick-in then the truck will lose braking ability for a short period of time. *ak
			08/19/1994
	Inapropriate abs engagement in wet or bumpy conditions. abs engages and vehicle coasts with sensation of increased speeds while brake pedal is being depressed.
05/22/1998		1	04/25/1994
	Accident caused by abs brakes failing. the driver felt two pulses in the brake pedal before it dropped to the floor during an emergency stop.
04/10/1998
	When applying the brakes the pedal went to the floor and vehicle did not stop.this occurred in dry weather on flat level surface on a cement street. dealer can't duplicate the problem. the defect has occurred twice at 40,000 miles. *ak
		1	03/01/1997
	Anti lock brakes pull to the right and left when applied.
		1	08/16/1994
	Brake failure.
02/02/1994			12/11/1993
	Abs brake problems; when depressing the brake pedal going over rough road/wet road/painted surfaces/repaired road conditions, the abs kicks in and the pedal goes to the floor there is extended stopping distance. the dealer stated that this is a normal condition. *ak
			11/01/1993
	Abs activate at 5 mph in various situations.
08/01/1997		4	10/22/1994
	When applying the abs brakes the pedal will travel to the floor, causing extended stopping distance which nearly caused a collision to occur. *ak
10/21/1997		1
	Driving about 35mph; suddenly had to depress brake pedal hard for quick/emergency stop; but vehicle continued & hit another vehicle trying to enter lane. dealer said foot was off brakes at time of accident. *ak

	Abs brakes; when applying the brakes in normal conditions , the vehicle pulls right to left; and when applying in panic stops, the brakes fail to stop the vehicle. *ak
03/01/1997		3
	Abs brakes failed intermittently on three different occasions, once resulting in a crash where vehicle rearended a mini van in front . *ak
		1	04/04/1996
	Anti lock brakes failed several times.
04/15/1996
	While driving the truck applied the brakes and the truck kept on going. the truck had extended stopping distance and once was involved in a collision. this year and model had a investigation listed. ea95- 026. *ak
11/20/1996		6
	An intermittent brake problem occurs. when driving the vehicle and stepping on the brakes the truck slides and the vehicle keeps going forward. *ak
07/01/1996		1	10/06/1993
	Brakes failed, causing driver to collide with another vehicle.
		1
	Anti-lock brakes have failed several times, on one occasion an accident occurred.

	When applying the brakes the pedal goes further than it should, and the vehicle does not stop because the brakes lock up. when wet outside there is no braking ability. dealer says nothing is wrong. *ak

	Intermittent abs problems with stopping 0n wet/dry pavement, especially on slightly rough roads. abs makes a growling noise when making a hard stop on unsmooth pavement, pedal goes to the floor, resulting in extended stopping distance. in addition, seat belt failure. *ak
01/07/1998			01/01/1994
	Faulty abs failed to stop vehicle allowing it to crash.
11/01/1997		2	11/01/1993
	Abs released brakes when engaged, pedal went to the floor, causing extended stopping distance on dry pavement. also, owner has been involved in two accidents related to brake problems. dealers replaced software in abs brake module, but problem continues. *ak
			11/09/1996
	The abs works occasionally. the vehicle slides and the brake pedal vibrates. this is accompanied by a grinding sound.
		3	07/04/1994
	Abs did not engage in emergency stopping.
		3	07/04/1994
	Anti-lock brakes malfunctions.
		11	10/20/1997
	Intermittently when the brakes are applied the abs engages and the vehicle pauses, and the brake pedal goes to the floor. the dealer has not been notified. *ak
		5	02/26/1994
	Brake pedal required excessive foot pressure to stop.
06/17/1997		2	05/01/1994
	While driving 35-40mph on a slippery surface, another vehicle pulled out in front, slammed on brakes & pedal went to the floor. did not hit vehicle, but skidded over the road. *ak
			07/01/1994
	On wet pavement when brakes are applied the vehicle slides and the brakes resist. on numerous occasions the vehicle has been to the dealer for repairs. *ak
10/15/1997		5
	While braking the abs is activated and vehicle experiences extended stopping distance/ brakes fading. *ak
11/18/1997
	When the brakes are applied around 40 mph and below, the vehicle experiences extended stopping distance. the brake pads/rotors have been replaced. *ak
04/16/1996		15	04/16/1996
	Abs brakes will lock up and fade, sometimes they will lock up, will not release, or pull to the left or right. has gone to four different dealers, cannot find problem. changed rotors/calipiers 13 times/proportional valve 2 times and master cylinders 13 times. defect is still occurring. ak slc
		2
	While braking on slick roads, vehicle starts to skid, loses all power to brakes. starts to skip, power does not come back until all pressure is off brakes. dealer said that is how it suppose to work. ak slc

	Owner has abs brakes. vehicle has extended stopping distance. when brakes are applied, problem occurs on wet or dry pavement. dealers found no problem with abs brakes. *ak

	Owner has abs brakes. vehicle has an extended stopping distance. also, there appears to be noise coming from abs brakes when they are applied. owner took vehicle into repair center and was told brakes have normal pad wear. *ak
01/01/1995		3
	Abs brake problems; on regular road conditions, during normal braking, when applying the brakes, the front of the truck will whip to the left. when taken to (3) different dealers a problem could not be detected. ak slc

	When applying the brakes could hear air escaping. the dealer said the booster had to be replaced. *ak
10/05/1997
	When the brakes are applied, the pedal goes to the floor. the vehicle continues to move. the owner has to pump the abs brakes in order to stop the vehicle. the dealer has been notified. *ak
10/08/1997		15
	While driving uphill, applied brakes, pedal went to floor; vehicle kept going; crashed into rear of another vehiucle; 15 mph. owner has experienced poor braking performances numerous occasions within 1 year, mostly low speed; intermittent. not duplicated by dealer. *ak
12/12/1993		2
	Abs brake problems; intermittently, while driving on regular road conditions during normal braking, the brakes start to hold but seem to release and more stopping time is required. when applying the brakes consumer does not know if the truck will stop or not in order to hit another vehicle. dealer stated that nothing was wrong with the brakes. ak slc
10/06/1994
	Whenever coming to a stop and hitting a bump in the road while foot is on the brake pedal , loses brakes and has to swerve off to the side of the road before the truck will stop. *ak
02/27/1997		1	10/01/1994
	Going down steep driveway when abs brakes failed to slow vehicle. vehicle hit tree head-on. driver sufferend serious injuries. engineer inspected vehicle and determined that a loss of brake fluid through a slow leak caused the brake failure. vehicle considered a total loss. *ak.et.
08/15/1997
	A vehicle pulled out in front of consumer who was driving approximately 35-40 mph when she slammed on brakes. the brake pedal went to the floor, but the vehicle continued to move forward, nearly causing a vehicle crash. *ak
11/10/1994
	Abs brakes are subject to intermittent failure, causing extended stopping distance. on other occasion, brakes make grinding sound while making a turn and applying the brakes, the pedal goes to the floor. *ak
08/22/1994		3	07/01/1994
	When putting on brakes the brake pedal goes down to the floor and hears a grinding noise, and the the truck will eventually stop.ak rear air conditioner control knobs will not stay attached to the control, dealer replaced the knob air conditioner does not blow cold at an idle. both front axle seals were leaking out fluid from the left front axle, dealer replaced both seals and right axle. oil pressure gauge dips down into the red at an idle. temperature gauges reads hot. slc
09/11/1997		1	12/01/1993
	While driving 25 mph , depressing the brakes vehicle continued to move, causing the vehicle to collide into another vehicle. the dealer will be notified. ak slc

	Brakes were applied and they resisted. foot would be to the floor of the vehicle . vehicle was taken to midas. the brake system was replaced. *ak
10/23/1995
	Noticeable development of funny noise; thereby causing reduction in brake (abs) effectiveness. *ak
12/23/1996		3
	Brakes: when road is slipperuy or wet slowed down to make turn, tapped brakes lightly there was total loss of brakes.this has happened on three different occasions. pedal does not go completely to the floor and there is no problem as long as the highway is dry. *ak
06/01/1996		1	02/22/1996
	Consumer had to make a panic stop, the brake pedal went to the floor of the vehicle, and the brakes resisted. the dealer has been notified. ak consumer states that the brake pedal was held all the way to the floor, and the vehicle gradually slowed, consumer states that the brake pedal was not pumped and the brakes did not make any noises. slc
		3
	When applying the abs brakes in a sudden stop, the pedal goes to the floor and the brakes fail to stop the vehicle. *ak

	If the vehicle hits a bump while the brakes are being applied, the abs kicks in and surges the car forward. dealer rebuilt the brakes. *ak
10/21/1997
	Ea94-038, on routine checkup, the vehicle had to replace the front braking system, and the brackets that hold the braking system at 21 miles. *ak
			09/01/1995
	When applying the abs brakes the pedal will travel to the floor, causing extended stopping distance which caused an accident. also, the abs warning light illuminated, indicating malfunction within the system. dealer reset the light which did not remedy the problem. *ak
01/29/1997		1
	Antilock brake failure.
03/01/1994		1	03/01/1994
	Ea95-026 active, brake failure, when brakes are applied the vehicle pulls to the right, causing loss of control/ vibration. also the pedal is very low. *ak
03/27/1997		1
	Antilock brakes failed.

	Vehicles abs braking system intermittently experiences soft pedal and extended stopping distances, feels like air is in the lines.(ea95-026). *ak
03/06/1996		1	05/01/1994
	Antilock brakes failed, causing accident.
07/07/1994			04/01/1994
	Abs failure, when applying the brakes the pedal goes close to floor and the vehicle does not stop in time. when hitting any kind of bumpy road the vehicle feels like it hydroplanes. vehicle taken to dealer (3) times. problem still exists. *ak
		3
	While driving experienced abs brakes malfunctioning. when applying brakes they grabbed/released, then continued to roll forward, brake action seemed inadequate to effectively stop vehicle fast enough, not fixed. *ak
09/01/1994
	When applying the abs brakes the pedal will at intervals travel to the floor, causing extended stopping distance, resulting in a crash. *ak
			08/01/1993
	Ea95-026; on dry road surface or panic stop abs brakes fail to respond, allowing extended stopping distance. *ak
01/01/1994
	Abs problems; on normal road condtions when putting on the brakes quickly the pedal goes to the floor and the brakes take a while to catch and when they do they lock up. vehcile taken to dealer once, nothing fixed on vehicle. *ak

	Abs failure, when slamming on the brakes hard on normal road conditions, the pedal went down and vehicle slammed into the rear of another vehicle, doing about $4500.00 worth of damages. vehicle is being repaired at this time. *ak

	Kelsey hayes abs failure, when applying the brake the pedal goes to the floor and it takes a longer time to stop the vehicle. this happens on normal road conditions. vehicle was involved in a crash 1/96 because of problem. not seen by mechanic. *ak
		10	06/17/1994
	Abs caused brakes to completely release, not allowing vehicle to stop in time to avoid collision. dealer claims nothing is wrong.
		10	07/17/1994
	Abs has premature release when on city street/dry pavement. excessive stopping distances are incurred including sliding through intersections.
01/01/1997
	Abs brake failure, in wet weather intermittently brakes have extended stopping distance. *ak
01/22/1997
	When driving on wet pavemnet upon applying force to the brake pedal the vehicle will continue to move, resulting in extended stopping distance/brakes fade away, could result in a near accident. ea95-026. *ak

	Abs brakes lock up under normal driving conditions while braking. please describe. *ak
01/01/1995
	Ea95-026 active, brake failure, applied the brake pedal and it goes to the floor, vehicle will not stop, intermittently fails , experienced pedal fading. *ak

	#ea95-026, on 10 to 15 different occasions the brake pedal was hard and vehicle didn't stop . *ak
12/12/1996		3	09/01/1994
	Ea95-026 active, when brakes are applied, pedal goes to the floor, loss of brake effectiveness, also feels like the cruise control kicks in. *ak
06/15/1995
	Poor abs brake performance, extended stopping distance has taken place on several occasions under normal braking conditions. *ak

	When applying the abs brakes, the pedal went to the floor and the brakes failed to stop the vehicle, causing an accident. *ak
		5	01/01/1994
	Antilock brakes release upon hitting small bumps in roadway, causing loss of control.
12/06/1996
	When applying the abs brakes in a sudden stop situation, the vehiicle brakes failed to stop the vehicle, causing an accident. *ak
11/14/1996		1
	The cruise control would not disengage when hitting the brakes and the vehicle kept accelerating, causing an accident when vehicle went through a red light. *ak
10/29/1996
	When applying the brakes the pedal went all the way floor and the vehicle failed to stop and rearended another vehicle. the road conditions were perfect. the system has abs. *ak
02/01/1994		3	03/31/1994
	Antilock brakes failed 3 times.

	When applying the abs brakes in sudden stop situations, the vehicle's brakes failed. *ak
07/07/1996
	When driving on normal road conditons and applying the brakes they pulsate and make a funny noise. this happens intermittently. the system has abs. *ak
09/12/1994		1
	Failure of the abs braking system, when driving on wet an dry pavements the vehicle will not stop, causing the consumer to have near accident.*ak
01/01/1996		12	06/01/1994
	While driving experienced intermittent abs failure, upon braking noticed grinding noise and vibration, brakes grab then release, pedal goes to floor and continues to roll forward.*ak

	On three occsasions in dry weather when applying the brakes, there are no brakes, has abs anti-lock brakes . please describe .*ak
07/29/1996		1	08/25/1994
	Ea95-026 active, brake failure, pedal goes to the floor ,abs light comes on lost of effectiveness. ak consumer took vehicle to dealer and rear brakes were adjusted, currently abs light stillcomes on, and brakes still feel spongy.jb
07/25/1995		5
	Antilock brakes system failed to stop vehicle, resulting in accident. *dh
02/16/1996		6
	Abs engages when it shouldn't, causing extended stopping distances. *dsh

	While driving, at approx. 5-10mph, experienced intermittent brake failure, when made attempt to stop pedal went to floor & vehicle continued to roll forward.*ak
03/12/1994
	Failure of the abs brake system, causing the consumer to have an accident, failure on the front seat belt, belt will not retract. *ak

	When applying brakes the abs does not kick in, have gone through several stops signs because of the problem. *ak
05/02/1996
	The truck is equipped with abs. when coming to a low speed stop, the brakes will not activate and the truck will not stop. please describe. *ak
05/01/1996
	Poor brake performance, consumer having a hard time stopping the vehicle ea95-026. *ak
04/16/1994		6
	Antilock brakes inadequate on bumpy road surfaces, also make clicking noise. *dsh
04/08/1996		8
	Abs braking system when engaged causes the vehicle to slid. *sd
09/15/1994
	Abs: anti lock brake system seemsto activate early when applying brakes, especially on bumpy surface, abs sticks in, vehicle will not stop/accident. *ak
12/10/1995		0
	Antilock brakes failed. *sd
03/25/1996		5
	Abs pump replace due to leaking/brake failures. *sd
11/06/1995		6
	Antilock brakes failed. *sd
04/05/1996
	When applying the brakes the truck failed to stop and caused an accident. the truck is equipped with abs. please describe. *ak
10/12/1995			10/01/1994
	The abs brakes locked up, vehicle often pulled to the right, almost causing a near accident. also, replaced brake pads/calipers. ea95-026. *ak

	Abs brakes; brakes don't respond to pedal travel w/bumps interfering. please describe details. *ak
03/04/1996
	The abs brakes keep failing. when applied the brakes do not work and they also freeze up. please describe. *ak
10/01/1995
	Vehicle is equipped with abs brakes, when applying, brakes will not stop vehicle. *ak

	Abs brakes; banner chev la; brakes failed to stop vehicle when applied. this dealership states no problem w/brakes. *ak
10/30/1995		0
	Antilock brakes failed 4 times, causing accident/loss of control/injuries. *sd
01/01/1996		1
	Ea95-026 active, abs brake failure, resulting in extended stopping distance. tt

	Abs brakes; brakes respond poorly. please describe details. tt
07/04/1994
	When towing a trailer the abs brake system malfunctions, resulting in long stopping distance. tt
12/22/1995
	The vehicle has abs brakes and they have failed several times. please describe. tt
12/21/1995
	The abs system is not working well.please describe. tt

	Ea95-026; abs brakes; upon application, brakes had delay in response which resulted in accident. please describe details. tt
07/10/1995
	#ea95-026; abs: poor stopping distance caused driver to have front end accident. please describe. tt
06/26/1995		6
	Antilock brake failure, causing accident/injury. *aw
04/10/1995
	# ea95-026 poor performance of abs. please describe. tt

	Abs system is much to senitive and much too frequently, grinds before coming on. please describe. tt
06/01/1995
	Poor performance of the abs brake system ea95-026. tt
12/09/1994
	In repair shop seven times for abs. brakes felt like they were holding for a little bit. please describe. tt
11/30/1995
	Abs system locks up and pulls to one side. please describe. tt
10/24/1995		1
	The truck has abs brakes. when road was wet the brakes would not stop at all. tt brakes failed to stop.*jb
11/09/1994
	When coming to a stop and on a bumpy road the abs system will activate and the truck will not stop. please describe. tt
12/01/1994
	Abs: doesn't function properly. in for service once already. please describe details. tt
06/25/1995		3	10/20/1993
	Experiencing extended stopping distances. had brake pads and shoes replaced. tt
11/03/1995
	Poor performance of the abs system, excessive brake pedal travel. tt
09/12/1995
	The abs system fails. the vehicle will not stop when brakes are applied. please decribe. tt
03/20/1994
	Ea95-026- braked surge forward consumer was thrown forward truck was taken to dealer they found air lock on brakes this has happened 3 times since. tt
11/01/1994		1	08/01/1994
	Experienced brake failure, when made attempt to slow down, brake action seemed ineffective, pedal went to floor, during panic stop, hit another vehicle. tt *jb
		1	04/01/1994
	Ea95-026 on emergency and regular braking sometimes there no brakes have abs anti-lock brake . tt on hard braking, occasional grinding and total brake slippage.*jb

	During panic stop, experienced brake failure, when pedal went to floor and continued to roll forward at approx. 35mph, no prior warning. tt
10/13/1995
	Poor performance of the abs brakes system, excessive pedal travel. tt

	Intermittent failure of abs to go on. no brakes when this happens. tt
03/01/1994
	Consumer was driving went to apply the brakes failed. tt
		1	11/01/1993
	Vehicles abs braking system intermittently activates on dry roads.at 19,000 miles the brakes and rotors had to be replaced. tt *slc
03/06/1995		6
	Delay in braking response when depressing antilock brakes. *aw
10/06/1995
	The abs system does not brake well. takes longer to stop. please describe. tt

	When consumer hit a bump in the road and the brakes are applied the abs brakes kicks in. tt
07/05/1995		1
	The abs system requires high pressure on braking resulting in depression before engaging full engagement, which has resulted in locking and skidding on wet surface or sandy road surfaces.*jb
10/03/1995		8	02/01/1994
	Abs brake failure. tt brakes failed when braking on a wet surface, almost causing an accident. *slc

	#pe95-023 in the middle of the braking the truck jump forward 20 to 40 feet have abs anti-lock brake . tt
09/15/1995
	Abs system failure, intermittent loss of braking ability. tt
08/06/1995
	The truck has abs brakes. they fail and have caused an accident. please describe. tt
01/28/1994		8
	Anti-lock brakes failed, resulting in an accident/injuries. *ak
06/08/1995		8
	Anti-lock brake system locks up, causing sliding/extended stopping distances. *skd
10/24/1994
	Due to brake failure vehicle knocked child down and ran over his arm. tt

	Abs brakes; when applied (13) times, brakes fail to respond. please describe details. tt

	Abs brakes; occasionally weird noise with no braking and with road disfiguration brakes fail to respond. please describe details.

	#pe95-023 poor brake performance abs anti-lock brake . tt
08/30/1995
	The abs system locks up and then releases and they do not seem to hold . please describe. tt

	Vehicles abs braking system is causing excessive wear of pads and equipment.especially the right hand side. tt
07/30/1995
	Pe95-023 active, when applied brakes, loss of brake effectivess, when trying to stop enbankment went into 6 ft. water. tt
06/22/1995		2
	Abs brakes failed, resulting in two accidents. *ak
07/02/1995
	The abs brakes shutters when you make a quick stop and the rigth side fells as thought it locks up and it pulls to that side. please describe. *ak
01/18/1995		1
	Abs anti-lock brakes: when truck is cold coming to a stop signal the truck doesn't stop, went through the stop sign in the middle of the street. tt
03/21/1995		1
	Abs system activates when going over bump and rear wheels leave ground, causing unwanted increase in vehicle speed. *tw
04/27/1995		7
	Anti-lock brake failures, causing brakes to fade. *skd
11/24/1994		4
	Abs brake system failed, 1 time resulting in accident. *tw
11/30/1994
	Driving along when i noticed that abs brakes had failed without prior warning. tt
05/21/1995		1
	The abs system brakes are wearing out prematurly due to size/weight of vehicle. *ak
01/01/1995		1
	Antilock brakes engage when braking on wet roads, causing pedal to travel to floor. *aw
11/20/1994
	Abs: when braking at hard stop, vehicle keeps on rolling; vehicle too heavy for brake design. tt
04/15/1994		12
	Abs: brake pedal intermittently goes to floor; nearly caused an accident. tt
03/21/1995		10
	Abs system failure, causing total loss of braking ability. tt
03/20/1995
	Abs system failure. tt
12/12/1993
	Abs anti -lock when slow down hit a bump brake go down to the floor consumer pump brake it came back been having problem 12/12/93 when purchase van. tt
02/03/1995
	Abs brakes locked up periodically when applied at any speed. please describe details. tt
11/07/1994		1
	Anti-lock brakes fail, causing brakes to lock/vehicle to skid. *skd
SERVICE BRAKES, HYDRAULIC - ANTILOCK - CONTROL UNIT/MODULE
02/01/1995		1
	Anti-lock brakes do nto engage fast enough over rough roads. kt
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS
09/23/1998
	Every the brakes are pressed, would have severe pulling to the left. happens every time. there is a tsb #86-50-20a. dealer refuses to repair for free. the wiper motor do not come on unless wires are jiggled first. manufacturer #98043. vehicle vin did not fall under recall.
02/02/1998		1	11/11/1994
	Brakes failed.
04/16/1996		15	04/16/1996
	Abs brakes will lock up and fade, sometimes they will lock up, will not release, or pull to the left or right. has gone to four different dealers, cannot find problem. changed rotors/calipiers 13 times/proportional valve 2 times and master cylinders 13 times. defect is still occurring. ak slc
			11/01/1995
	Spring load keeper which secures stop light switch which in turn secures linkage from brake lever to master cylinder, may fail, rendering entire braking system inoperative.

	While on wet pavement when brakes are applied truck goes into a skid. consumer has contacted dealer. *ak
12/11/1996		0
	While driving vehicle applied the brakes, brakes failed intermittently, nearly rearended another vehicle, taken to dealer who put it on computer, nothing showed up for problem with brakes. *ak
09/12/1996
	While trying to apply the brakes the brakes faded, almost causing an accident. *ak
04/12/1995
	Vehicle squeaks and around 40 to 50 mph brakes feel spongy, appears car will not stop.*ak
08/07/1995		6
	When applying the brakes there is no brake action, have hydraulic brakes . ak the only action that the dealer takes is bleeding brakes and master cylinder to remove air from the brake liines, however this does not remedy the problem, consumer has to pump brakes to get them to work. transmssion slow to engage, dealer found actuator feed limit valve sticking. rear blower on ac gave nothing, dealer repaired wire to blower motor. repaired wiring to faulty taillamp assembly. slc
02/27/1996		7
	Brakes failed. *dh
09/30/1994		0
	Brakes fail repeatedly after several repair attempts. *dsh
09/21/1994		1
	Brakes failed four times, once causing accident. *sd

	The brakes keep failing and keep having to be replaced. tt
10/24/1995
	Poor performance of brake failure ea95-026. tt
10/31/1995
	Tried to brake suddenly, brakes did not stop vehicle adequately. tt

	During panic stop, brake failed. tt

	When apply the brake there is a grinding noise brake goes to the floor cause consumer on three occasions to rear end car in front . tt
01/24/1995		4
	Vehicle exhibits extended stopping distance when brakes are applied in emergency situations. *ak

	Brakes failure, is leaking. tt
01/28/1995		8
	Intermittent brake failures after repairs, causing loss of control/one accident/injuries. *skd
06/07/1994
	Brakes pulls to the right, also pedal fades out intermittently, disable abs to no avail. tt
01/14/1995		3
	Brakes failed 3 times, once resulting in an accident. *ak
01/28/1995
	The brakes have failed all around on the vehicle that is 5 months old and there are 20,ooo miles.please describe further. tt
12/17/1994
	When applying the brakes pedal goes to the floor. tt
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC
10/18/2002		2	01/01/2000
	Truck pulls most often to the left when braking sometimes to the right sometimes goes fine. dt
			10/01/1997
	The antilock brakes on my 1994 gmc suburban perform very poorly on wet pavement. the stopping distance is increased greatly and has led to one accident. several other times increased stopping distances has led to near accidents. this has caused us to operate the vehicle very cautiously in wet weather. the accident was on wet pavement. when the brakes were applied the pedal began to pulsate and then went clear to the floor, yet the vehicle acted as though the brakes had released. braking action was almost gone causing us to slide into the rear of another unit. there was sufficient distance to stop had the brakes not release the braking action.
07/15/2001		6	07/01/2001
	Front disc brakes do not release, causing excessive heat in rotors,hubs, and wheels. *ak
			02/08/1996
	Abs brakes fade and are non-responsive in an emergency situation. also, replaced front brake calipers/pads and rotors. *ak
11/18/1997
	When the brakes are applied around 40 mph and below, the vehicle experiences extended stopping distance. the brake pads/rotors have been replaced. *ak

	Disc drum power brakes; when applying brakes on two separate instances, once brakes were applied the vehicle continued through intersction. truck was inspected 2/94 and 8/97. dealership unable to duplicate cause(s) complete loss of brakes. please describe details. *ak

	While driving experienced brake hydraulic system malfunctioned when attempting to slow/stop, vehicle continued to roll forward, front brakes only stopping vehicle, rotors resurfaced and pads replaced twice, brake action seems inadequate to effectively stop.
11/28/1994		1	09/30/1994
	On slippery surfaces the front wheels lock up while the back wheels keep on rotating. *ak

	When apply the brakes there is a noise in the front. tt
05/10/1995		1
	Warped frpnt brakr calipers/pads/rotors, causing vehicle to vibrate upon braking. *ak
05/22/1995		1
	At 7 mph or less the front wheel locked up when braking. tt
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - CALIPER
04/23/1997		1	07/03/1994
	Brake calipers stick resulting in overheating of brake components, warping rotors.
10/12/1995			10/01/1994
	The abs brakes locked up, vehicle often pulled to the right, almost causing a near accident. also, replaced brake pads/calipers. ea95-026. *ak
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - PADS
07/18/1999
	When the brakes are applied the vehicle vibrates and fades resulting in extended stopping distances. the dealer has replaced the pads several times. the manufacturer has been notified. mjs

	Owner has abs brakes. vehicle has an extended stopping distance. also, there appears to be noise coming from abs brakes when they are applied. owner took vehicle into repair center and was told brakes have normal pad wear. *ak
01/11/1996		1
	Front inner brake pads worn, causing partial loss of control. *tt
10/12/1995			10/01/1994
	The abs brakes locked up, vehicle often pulled to the right, almost causing a near accident. also, replaced brake pads/calipers. ea95-026. *ak
01/01/1996		1
	Premature wear of front brake pads. *ak

	Experiencing extended stopping distances. had brake pads and shoes replaced. tt
06/27/1995		7
	Premature brake pad wear. *aw
09/20/1995
	Brake failure, replace of pads, master cylinder failure, loss of effectiveness. tt
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - ROTOR
04/23/1997		1	07/03/1994
	Brake calipers stick resulting in overheating of brake components, warping rotors.
01/01/1996		1
	Premature wear of front brake rotors. *ak
06/27/1995		7
	Rotors replaced due to premature wear, replacement rotors require excessive pressure to be applied to brake pedal to stop vehicle.

	The rotors are carcked and the drums are burnt. please describe. tt
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM - DRUM

	The rotors are carcked and the drums are burnt. please describe. tt
03/24/1994		3
	Rear drum failed, causing excessive squeal. *ak
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - MASTER CYLINDER
04/09/1996		1
	Master cylinder failed causing leaking.
08/22/1995
	Owner has abs brakes but notes that the master cylinder has been faulty, when brakes are used vehicle tends to keep going , even after the master cylinder was replaced, owner also notes that pedal goes to the floor when brakes are used. *ak
09/20/1995
	Brake failure, replace of pads, master cylinder failure, loss of effectiveness. tt
06/02/1995		3
	Brake system failure, replaced leaking master cylinder three times. tt
SERVICE BRAKES, HYDRAULIC - PEDALS AND LINKAGES
04/12/1995
	Vehicle squeaks and around 40 to 50 mph brakes feel spongy, appears car will not stop.*ak
01/24/1995		4
	Brake pedal is lower than the gas pedal.
02/07/1994		7
	Low/mushy brake pedal.
12/06/1994		1
	Brake pedal goes to the floor intermittently, resulting in extended stopping distance, also front disc pads replaced due to left front brake overheating.
SERVICE BRAKES, HYDRAULIC - POWER ASSIST
07/29/1996		1	08/25/1994
	Ea95-026 active, brake failure, pedal goes to the floor ,abs light comes on lost of effectiveness. ak consumer took vehicle to dealer and rear brakes were adjusted, currently abs light stillcomes on, and brakes still feel spongy.jb
SERVICE BRAKES, HYDRAULIC - POWER ASSIST - HYDRAULIC - HOSES, LINES/PIPING, AND FITTINGS
01/26/1995		2
	Bpmv failed two times.
SERVICE BRAKES, HYDRAULIC - POWER ASSIST - VACUUM

	When applying the brakes could hear air escaping. the dealer said the booster had to be replaced. *ak