International Harvester 9800 1997
Model 9800 made in 1997 by International Harvester got 2 recalls as well as 2 service bulletins. Technical service bulletines regarding engine and engine cooling and power train. There were some recalls concerningsuspension and vehicle speed control.
Model 1997
Recalls
Campaign | Manufacturer | Manufacturing date | Type | # of units affected | Date Owner notified Mfg | Recall Initiated by | Manufacturers of recalled vehicles/products | Report Recieved Date | Record Creation Date | Regulation Part Number | FMVSS Number | |||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
SUSPENSION - REAR | ||||||||||||||||
96V233002 | INTERNATIONAL TRUCK AND ENGINE | from 04/16/1996 to 10/16/1996 | V (Vehicle) | 1133 | 12/03/1996 | MFR | INTERNATIONAL TRUCK & ENGINE CORPORATION | 11/22/1996 | 12/19/1996 | |||||||
Defect Summary | The drive axle housings consist of a plate steel center section and two forged spindles, one of which is welded to each end of the center section. each spindle contains a keyway slot in which the locking tab for the wheel bearing nut locking mechanism is inserted. the length of the keyway slot may not be long enough to accommodate the tab causing the tab to be deformed or damaged during installation. | |||||||||||||||
Consequence Summary | This locking tab prevents the wheel bearing nut from loosening during vehicle operation. if this tab is deformed, the nut can loosen allowing the wheel to separate from the axle increasing the risk of a vehicle accident. | |||||||||||||||
Corrective Summary | Dealers will replace the drive axle housing nuts with a conventional wheel nut hardware system. | |||||||||||||||
Notes | Owner notification:owner notification began december 10, 1996. note: owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact navistar at 1-800-448-7825.also contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393. | |||||||||||||||
VEHICLE SPEED CONTROL | ||||||||||||||||
96V181002 | INTERNATIONAL TRUCK AND ENGINE | from 04/03/1996 to 09/16/1996 | V (Vehicle) | 93 | 12/15/1996 | MFR | INTERNATIONAL TRUCK & ENGINE CORPORATION | 12/12/1996 | 12/19/1996 | |||||||
Defect Summary | These vehicles are equipped with a detroit diesel optimized idle system. if the ignition is turned on and the fuse for the electronic control module (ecm) power feed line is removed or burned out, unintentional cranking of the engine will occur.. | |||||||||||||||
Consequence Summary | If unintentional cranking of the engine occurs, the safety features designed to prevent injury to persons working in the vicinity of the engine will occur and also vehicle movement may occur increasing the risk of a vehicle accident. | |||||||||||||||
Corrective Summary | Detroit diesel distributors will rewire the vehicles using a revised ecm which will eliminate unintentional cranking. | |||||||||||||||
Notes | Owner notification:owner notification began during december1996. note:owners who take their vehicle to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contactdetroit diesel at 1-313-592-7357 or navistar at 1-800-448-7825.also contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393. |
Bulletins
Bulletin | Bulletin date | Replacement Bulletin | Item no. | Summary | Added |
---|---|---|---|---|---|
ENGINE AND ENGINE COOLING - ENGINE - GASOLINE | |||||
AFCG00905 | 04/01/2000 | 614819 | Some 9800sfa models with 89 inch cab, roof air deflectors and high horsepower engines built between march 6, 1996 and march 28, 1999 may require modification to the engine air intake system to prevent ingestion of contaminants (dirt, salt, | 12/14/2000 | |
POWER TRAIN - AXLE ASSEMBLY - AXLE SHAFT | |||||
IK-1400020 | 06/04/2012 | 10044295 | International: on certain model trucks built in brazil and south africa the axle shaft fastener is broken and the axle flange gasket is leaking. *pe | 06/06/2012 |