Bulletins


BulletinBulletin dateReplacement BulletinItem no.SummaryAdded
ENGINE AND ENGINE COOLING
IK120074808/10/201210045800International: oil seepage can be seen at joint connecting high pressure turbocharger piping and inlet of high pressure charge air cooler, if oil carryover is present. model maxxforce 11 and 13l. no model years listed. *pe09/17/2012
SB-IK120006109/29/200810029004International: low coolant light with international i6 egr and 2007 maxxforce engines (restriction fitting). model and model years unknown. *pe06/10/2009
001207R10/01/2001631684Subject regarding false coolant level warnings in 2000 and 8000 models built between october 1, 1997 and august 1, 2000; 5000 and 5000i models built between october 1, 1997 and july 1, 2000; 3000fe models built after november 1, 1997 with i06/10/2002
TSI96122510/01/1996629990Some vehicles may have low engine power and a leak in the charge air cooler is suspected. *tt04/10/2002
TSI01121106/01/2001623562Information regarding refilling 4300, 4400 cooling systems. *yh10/29/2001
ENGINE AND ENGINE COOLING - COOLING SYSTEM
TSI01120302/01/2001622881Subject regarding water pump update for all international i6 engines. *tt10/24/2001
ENGINE AND ENGINE COOLING - COOLING SYSTEM - FAN
IK-090006910/22/201210049003International: some trucks , to prevent interference between fan drive bracket and coolant fitting, a notch should be in fan drive bracket. no models or model years listed. *pe01/08/2013
IK-120081110/03/201210048959International: because of restrictions in air line going to fan clutch solenoid, premature fan clutch wear causes fan drive to be inoperative. no models or model years listed. *pe01/07/2013
IK-090007108/24/201210045799International: the cause of failures and necessary replacement of fan drive is horton stratis fan hub wires rubbing. re-routing after multiple failures prevented and re-routing before future failures prevented. no model or model years l09/17/2012
IK-120019301/27/201210043360International (navistar): trouble with engine fans. no model or model years listed. *pe03/20/2012
SB-IK120035703/11/200910030144International truck: certain horton 2 speed fan drives may have either loose or missing magnets. an updated fan center section kit is available for repair. symptoms: missing fan drive magnets, loose fan drive magnets, hood damage, fan blad08/07/2009
TB-K-090002403/13/200910030130International truck: maxxforce 11 & 13 fan drive torque specifications: the nut from the drive to the engine is 113 to 153 nm. the fan at top speed is 250 nm which tights it more so removal is much higher than the tightening torque. the six08/05/2009
ENGINE AND ENGINE COOLING - COOLING SYSTEM - HOSE
0290611/01/200210000476Rerouting the heater return hose to extend radiator life. *tt02/28/2003
ENGINE AND ENGINE COOLING - COOLING SYSTEM - RADIATOR ASSEMBLY
TSI01160101/01/2001622883Subject regarding bunk thermostat relocation in 9000 and 9000i models with optimized idle, international code 12vws. *tt10/24/2001
ENGINE AND ENGINE COOLING - ENGINE
IK-120070902/29/2012IK-120070910043467International: the egr hot side inner and outer bellows are cracked and/or have exhaust leaks on field trucks. *pe updated 4/11/2012. *kb04/03/2012
IK-120070901/23/201210043467International: the egr hot side inner and outer bellows are cracked and/or have exhaust leaks on field trucks. *pe04/03/2012
IK-120059704/27/201110040293Ready08/17/2011
IK-120059704/27/201110040293International truck: there are stored trouble codes. *rm08/17/2011
IK-260001501/09/200810032288International bus: international reprogramming harness. this sfn applies to all post 11/97 international engine control modules except 3-box. engine reprogramming harness allows the technician to power the engine ecm and idm without usin03/01/2010
IK-120039709/25/200910032184International truck: aps overlay harness on maxxforce engines. intermittent aps/ivs codes with maxxforce dt and maxxforce 7. loss of throttle at times with known good aps. no model or model years listed. *pe02/17/2010
03120807/01/200310003472Intake air piping oil residue. *tt10/21/2003
03121108/01/200310003095Front and rear fan clutch diagnostic and troubleshooting procedures for international 12tkn, borgwarner k22, and international code 12tks, borg warner k26. *tt10/08/2003
032003/21/200310002300(engine control module) ecm software calibration correction for low power complaint. engine family ht530. *tt08/20/2003
03120502/01/200202120710002226Injector and glow plug harness change. *tt08/15/2003
03120304/01/200310002167Oil leaking from the high-pressure pump area. *tt08/14/2003
02122101/01/200310000896High-pressure oil pump service kit and instruction video. i6, dt466/e, 530e, dt 530, and ht 530 engine family. *tt04/02/2003
02122310/01/200210000354Relocation of the serial number on all i-6 engines. *tt02/24/2003
02122710/01/200210000355New torque value for fractured type connecting rod bolts. i-6 engines (model years 2000 and up). *tt02/24/2003
027109/05/200210000107Air solenoid programming procedure (for air operated features). *tt02/12/2003
ENGINE AND ENGINE COOLING - ENGINE - DIESEL
IK-120080808/27/201210045819International: oil pressure pikes displace wear sleeve to move up and return spring not strong enough to force back; oil pump limits oil pressure to fuel injection system by relief valve; replace wear sleeve with over sized sleeve increas09/17/2012
IK-120019301/27/201210043360International (navistar): trouble with engine fans. no model or model years listed. *pe03/20/2012
IK-120060405/16/201110040294Ready08/17/2011
IK-120003705/16/201110040290Ready08/17/2011
IK-120058702/22/201110040292Ready08/17/2011
IK-120058702/22/201110040292International truck: the transmissions are experiencing poor acceleration/ hesitation/ engine surge. *rm08/17/2011
IK-120003705/16/201110040290International truck: information on servicing and replacing the ecm adn components. *rm08/17/2011
IK-120060405/16/201110040294International truck: low coolant level warnings have been changed due to coolant surge tank markings that were causing intermittent low coolant warnings. *rm08/17/2011
IK-120043201/12/201010033556International: when turbocharger diagnostics lead to mechanical failure it is possible to separate the turbo housing to inspect internal components. the turbine housing is available as a serviceable component of the turbocharger assembly.08/23/2010
IK-120044001/27/201010033508International: new accelerator pedal sensors for pre-2010 emissions international engines. applies to pre 2010 emissions international engines. two (2) new aps sensors (accelerator position sensor) have been developed and released for us08/18/2010
IK-120019902/06/200810032947International: egr cooler and bracket installation procedure for maxxforce dt, 9 and diesel engines. applies to all international maxxforce dt, 9, and 10 diesel engines. a change has been made to the installation procedure of the exhaust06/16/2010
IK-120003202/11/200810032945International: repairing vt 275 icp leak on the front port plug and/or rear port and case to head tube. d rings should not be serviced separately on either port plugs or rear port and case to head tubes. replace the port plug and/or rear06/16/2010
IK-120009102/20/200810032946International: torque for high pressure rail oil adapters (oil pucks) and parts information. applies to model i-313 dt-466; dt-570 and ht 570 engines. torque spec on high pressure rail oil adapters (oil pucks). when servicing injectors06/16/2010
TSI-08-12-0402/01/200810032924International: change made to installation procedure of the exhaust gas recirculation (egr) cooler and bracket exhaust side. change to tighten the two m12x70 egr cooler bracket mounting bolts after (not before) the egr cooler clamps. no06/14/2010
TSI-08-12-0112/01/200710032289International: engine idle shutdown timer (ist) regulations. all international maxxforce diesel engines beginning with 2008 my. engines certified for sale in the state of california will conform to mandatory california air resources boar03/01/2010
IK-260001501/09/200810032288International bus: international reprogramming harness. this sfn applies to all post 11/97 international engine control modules except 3-box. engine reprogramming harness allows the technician to power the engine ecm and idm without usin03/01/2010
IK-120039709/25/200910032184International truck: aps overlay harness on maxxforce engines. intermittent aps/ivs codes with maxxforce dt and maxxforce 7. loss of throttle at times with known good aps. no model or model years listed. *pe02/17/2010
IK-120040709/22/200910032144International truck: revision to air compressor pulley nut torque value. provides a revision to the printed eges 345 service manual for the international maxxforce 7 diesel engine. no models or model years listed. *pe02/12/2010
TB-IK-070001003/12/200910030127International truck: exhaust clamps at engine retarder butterfly assembly on maxxforce 11 & 13. its necessary to replace the clamps that secure the engine retarder butterfly assembly if the clamps are loosened of removed. no models or mod08/05/2009
IK-120033812/02/200810028567International: due to normal operation of the air system on maxxforce 11 and 13 liter big bore engines, the constant cycling of the air compressor as unusual characteristics. models and model years unknown. *pe05/08/2009
02121908/01/2002635513Piston / flywheel / vibration damper compatibility used on vt365 diesel engines. *tt10/24/2002
02120204/01/2002635486This bulletin covers installation of crankcase breather assemly and service diagnostics for the detection of high and low exhaust restriction in catalyzed diesel particulate filters (cdpf) for green diesel engines. *tt10/23/2002
13130101/01/2002631679Subject regarding cat engine high road speed fault codes for all caterpillar engines. *slc06/10/2002
ENGINE AND ENGINE COOLING - ENGINE - GASOLINE
SB-IK120035703/11/200910030144International truck: certain horton 2 speed fan drives may have either loose or missing magnets. an updated fan center section kit is available for repair. symptoms: missing fan drive magnets, loose fan drive magnets, hood damage, fan blad08/07/2009
02121709/01/2002635510Upper radiator pipe for cummins n14 engine used on 2500 and 2600 models. *tt10/24/2002
02121508/01/2002635508Under valve cover (uvc) harness retainer clip service kit. *tt10/24/2002
02120803/01/2002635519Subject regarding new exhaust back pressure (ebp) piston rod assembly kit. *tt10/24/2002
02121408/01/2002635507Performance specifications for 2002 model year ht 530 engines. *tt10/24/2002
02120702/01/2002635485Subject regarding injector and glow pulg harness change for international t444e engines. *tt10/23/2002
02120906/01/2002635473Release of new fractured connecting rod assembly. international i-6 engines (model years 2000 and up). *tt10/23/2002
01121410/01/2001631685Subject regarding reinforcements for fan shrouds that may flex, includes 9900 models built between july 6, 1998 and july 1, 1999 and 9000i models built between july 1, 1999 and august 27, 2001. *slc06/10/2002
TSI02120102/01/2002631530Subject regarding chassis cleaning procedures for low engine power or overheated engines, all models except 3000re bus. *tt05/31/2002
TSI011216R12/01/2001TSI011216631529Information on possible electronic variable response turbocharger (evrt) damage. *tt05/31/2002
SFN022303/01/2002631214Subject regarding afc g-01914, insufficient torque on the engine oil pick-up tube support mounting bolt and nut. *tt05/21/2002
SFN022303/13/2002631255Subject regarding afcg-01914, insufficient torque onthe engine oil pick up tube support mounting bolt and nut. *tt05/21/2002
TSI01120403/01/2001629991Subject regarding t444e engine knock at low idle with split-shot injectors. *tt04/10/2002
001207R10/01/2001626003Some vehicles including models 2000, 3000, 5000, 5000i, and 8000 may experience a false coolant level warning. *slc12/12/2001
TSI01120704/01/2001623530Information regarding lower thrust main bearing on dt466,dt 466e, dt 466e ht, dt 530 and 530e, 530e ht. *yh10/29/2001
TSI01120605/01/2001623526Subject regarding release of field replacement engines for 1994-2001 model year t 444e engines. *yh10/29/2001
TSI01120201/01/2001622879Subject regarding extension tube for road draft exhaust opening. *tt10/23/2001
TSI001206R01/01/2001TSI001206622878Subject regarding new cylinder head bolts and torque values for all i6 huei engines. *tt10/23/2001
G9850712/01/1998614719Vehicles with a high-pressure oil line for the fuel injection system that goes from the high pressure pump to the right cylinder head may fail due to rubbing on the charge air cooler crossover pipe. *tt12/11/2000
G9990205/01/1999605839Vehicles with dt 466e f230 / 250 engines, code 12nkh and 12nkj built between may, 1998 and october, 1998 may exhibit poor acceleration and stumble when the oil temperature is between 30 degrees f and 80 degrees f. *tt07/29/1999
ENGINE AND ENGINE COOLING - ENGINE - GASOLINE - BELTS AND ASSOCIATED PULLEYS
03121008/01/200310003094Belt wear on international vt 365, t 444e, dt 466, and 530 engines. *tt10/08/2003
ENGINE AND ENGINE COOLING - ENGINE - GASOLINE - TURBO-CHARGER
IK-120084111/26/201210049419International: on some trucks, the turbocharger has excessive smoke, or engine light comes on, or have no acceleration, or power is low and may be intermittent, no model or model years listed. *pe01/15/2013
TSI01121601/01/2002632431Subject regarding electronic variable response turbocharger (evrt) for ht 530 engine. *tt07/16/2002
TSI00120102/01/2001622877Subject regarding four-post compressor housing for all i6 engine applications. *tt10/23/2001
ENGINE AND ENGINE COOLING - ENGINE - OTHER FUEL TYPES - TURBO-CHARGER
IK-120016310/30/200710028568International: low power can be intermittent; no acceleration; excessive smoke; engine light on. ecm logs dtc 353 and/or dtc 354 codes when exhaust back pressure is too high or too low for specific engine operating conditions. models and mo05/08/2009
ENGINE AND ENGINE COOLING - EXHAUST SYSTEM - EMISSION CONTROL
IK 120029207/03/200810025962International: exhaust fumes in cab troubleshooting with 2007 engines. applies to vehicles with 2007 emissions engines. model and model years unknown. *pe09/18/2008
ENGINE AND ENGINE COOLING - EXHAUST SYSTEM - MANIFOLD/HEADER/MUFFLER/TAIL PIPE
IK-120058403/18/201110040291Ready08/17/2011
IK-120058403/18/201110040291International truck: there is an exhaust leak due to an egr sensor problem. *rm08/17/2011
TSI01080105/01/2001623456Subject regarding erratic exhaust pipe pyrometer gauge, code 16hgk, needle movement in 5000,5000i,9000,and 9000i models built before january 01,2000 with cb radios. *yh10/29/2001