Recalls
Campaign | Manufacturer | Manufacturing date | Type | # of units affected | Date Owner notified Mfg | Recall Initiated by | Manufacturers of recalled vehicles/products | Report Recieved Date | Record Creation Date | Regulation Part Number | FMVSS Number | |||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
ENGINE AND ENGINE COOLING - ENGINE | ||||||||||||||||
01I002000 | ISUZU MOTORS LIMITED | I | 06/22/2001 | MFR | ISUZU MANUFACTURING SERVICES OF AMERICA | 05/29/2001 | 06/05/2001 | |||||||||
Defect Summary | This is not a safety recall in accordance with the safety act. however, it is deemed a safety improvement campaign by the agency. vehicle description: 1998-2000 rodeo (ue) and amigo (ua) models equipped with 2.2l 4-cylinder engines. the timing belt could break before the recommended scheduled maintenance. | |||||||||||||||
Consequence Summary | This condition could cause the engine to crank but will not start or the engine could stall while driving and will not restart. | |||||||||||||||
Corrective Summary | Dealer will inspect the vehicle to determine the condition of the timing belt and tensioner. the dealer will replace the timing belt. depending on the condition or model of the timing belt tensioner, the tensioner may also be replaced. isuzu has decided to conduct a service campaign to replace the timing belt. owner notification began june 22, 2001. owners can contact isuzu at 1-800-643-4070, ext. 426, concerning this program. | |||||||||||||||
Notes |
Bulletins
Bulletin | Bulletin date | Replacement Bulletin | Item no. | Summary | Added |
---|---|---|---|---|---|
ENGINE AND ENGINE COOLING - ENGINE | |||||
IB0101S002 | 06/01/2001 | 621368 | Subject regarding hec engine timing belt scrapping. *tt | 09/18/2001 | |
IB0104S002 | 03/01/2001 | 621343 | Subject regarding p0337 crankshaft position sensor circuit low input correction. *tt | 09/17/2001 | |
ENGINE AND ENGINE COOLING - EXHAUST SYSTEM | |||||
SB0002S002 | 03/01/2000 | SB0003S002 | 612593 | Service information regarding all affected vehicles with the p1441 evaporative emission code that has been diagnosed with no fault found from the appropriate flow chart in the driveability and emissions manual. *tt | 06/09/2000 |
Consumer Complaints
Fail date | miles | occurences | Purchase date |
---|---|---|---|
ENGINE AND ENGINE COOLING | |||
04/23/2008 | 107000 | 1 | 04/21/2008 |
I own a 99 isuzu amigo with a 3.2l v6. the rod and main bearings have gone causing it to knock real bad. car cannot be driven anymore. *tr | |||
ENGINE AND ENGINE COOLING - ENGINE | |||
11/01/2004 | 87000 | 1 | 08/11/2003 |
My isuzu amigo (1999 4wd) stopped dead in traffic while driving with a lot of traffic. i was scared to death and almost hit in multiple directions. the car would not start, would not move, and i had to have it towed on a flatbed truck. i was incredibly traumatized by this incident, and very nearly killed by the semi-truck directly behind me. after contacting multiple persons from isuzu motors, they assured me that this had happened in most of the engines they had put in this vehicle. they also told me that if i was the original owner, they would fix it, regardless of warrenty, but since i was the second owner, they would not help me at all. since this was such a common problem, not to mention such a safety issue, i thought they would have been a little more helpful.*ak | |||
ENGINE AND ENGINE COOLING - ENGINE - GASOLINE | |||
Vehicle shut off without prior warning. dealership was aware of problem. *ak | |||
05/25/2001 | 1 | 02/12/2001 | |
While driving vehicle stalled without warning, also could not control vehicle until turning it off,contacted dealer and dealer stated there was nothing they could do. *ak *slc | |||
ENGINE AND ENGINE COOLING - ENGINE - GASOLINE - BELTS AND ASSOCIATED PULLEYS | |||
10/06/2005 | 70000 | 2 | 02/15/2000 |
The timing belt broke on the vehicle ruining the entire moto. the timing belt was a recall item and was replaced at around 20000 miles. the belt broke now at 70,000 miles. the vehicle has not been repaired in that it needs an entire motor at a cost of $4000. *nm |