Recalls
Campaign | Manufacturer | Manufacturing date | Type | # of units affected | Date Owner notified Mfg | Recall Initiated by | Manufacturers of recalled vehicles/products | Report Recieved Date | Record Creation Date | Regulation Part Number | FMVSS Number | |||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
SERVICE BRAKES, HYDRAULIC - ANTILOCK | ||||||||||||||||
02I002000 | ISUZU MOTORS LIMITED | I | 161927 | 07/14/2003 | ODI | ISUZU MANUFACTURING SERVICES OF AMERICA | 06/03/2002 | 06/05/2002 | ||||||||
Defect Summary | On certain sport utility vehicles that are equipped with an anti-lock braking system (abs), the vehicles can experience extended stopping distances in certain types of braking events. | |||||||||||||||
Consequence Summary | Extended stopping distance could result, increasing the risk of a crash. | |||||||||||||||
Corrective Summary | Dealers will provide a replacement computer algorithm for the abs that is based on the algorithm used in isuzu's my 2000 and 2001 vehicles, which have not had the problem. this campaign will be conducted in phases, with the my 1998 2wd vehicles covered first, since they have experienced the most problems. owner notification began march 20, 2003. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact isuzu at 1-800-643-4070. | |||||||||||||||
Notes | Customers can also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236). |
Bulletins
Bulletin | Bulletin date | Replacement Bulletin | Item no. | Summary | Added |
---|---|---|---|---|---|
SERVICE BRAKES, AIR - ANTILOCK - CONTROL UNIT/MODULE | |||||
0309S001C | 06/01/2003 | 0309S001D | 10001768 | Abs (anti-lock brake system), coil integrated module replacement safety improvement campaign. *tt | 06/25/2003 |
SERVICE BRAKES, AIR - DISC - ROTOR | |||||
0709002 | 07/01/2007 | 10022539 | Rear brake rotors. *kb | 08/20/2007 | |
SERVICE BRAKES, AIR - DRUM - SHOES/LININGS | |||||
9809L004 | 07/01/1998 | 602246 | A design change to the rear brake shoes. *yc | 10/20/1998 | |
SERVICE BRAKES, HYDRAULIC - ANTILOCK | |||||
9809L002 | 03/01/1998 | 600085 | Replacement of the coil-integrated module. *yc | 04/23/1998 | |
SERVICE BRAKES, HYDRAULIC - ANTILOCK - CONTROL UNIT/MODULE | |||||
0309S001C | 06/03/2003 | 10002164 | Abs (anti-locking brake) system, coil integrated module replacement phase 3 announcement. *tt | 08/14/2003 | |
0309S001C | 06/02/2003 | 10002163 | Abs (anti-locking brake) system, coil integrated module replacement safety improvement campaign 02i-002 phase 3 of a 4 phase release. *tt | 08/14/2003 | |
0309S001B | 04/01/2003 | 0309S001A | 10001777 | Abs (anti-lock brake system), coil integrated module replacement safety improvement campaign. *tt | 06/25/2003 |
0309S001A | 03/01/2003 | 10001776 | Abs (anti-lock brake system), coil integrated module replacement safety improvement campaign 02i-002. *tt | 06/25/2003 | |
SB0004S001 | 01/01/2000 | 612588 | Some vehicles may exhibit one or more abs diagnostic trouble codes such as: rear speed sensor open or shorted; speed sensor missing; wheel speed input abnormality. *tt | 06/09/2000 | |
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM - DRUM | |||||
IB0109S001 | 06/01/2001 | 621373 | Subject regarding drum brake adjustment procedure. *tt | 09/18/2001 | |
SB9909S002 | 11/01/1999 | 6088702 | Subject regarding 2wd rear drum brake adjustment procedure. *tt | 01/04/2000 | |
SERVICE BRAKES, HYDRAULIC - PEDALS AND LINKAGES | |||||
9802L003 | 12/01/1998 | 603034 | Information on the accelerator pedal pad replacement service campaign. *yc | 01/26/1999 |
Investigations
NHTSA ID | Manufacturer | Date open | Date close | Subject | Recall campaign | |
---|---|---|---|---|---|---|
SERVICE BRAKES, HYDRAULIC | ||||||
PE98051 | ISUZU MANUFACTURING SERVICES OF AMERICA | 09/23/1998 | 03/31/1999 | BRAKING SYSTEM/ABS | ||
Consumers alleged that they experienced a loss of braking capability that resulted in extended stop distance | ||||||
EA99008 | ISUZU MANUFACTURING SERVICES OF AMERICA | 03/31/1999 | 07/31/2002 | BRAKING SYSTEM/ABS | 02I002001 | |
Consumers alleged that they experienced a loss of braking capability that resulted in extended stopping distance, and/or illumination of the abs warning lamp. | ||||||
EA99008 | ISUZU MANUFACTURING SERVICES OF AMERICA | 03/31/1999 | 07/31/2002 | BRAKING SYSTEM/ABS | 02I002000 | |
Consumers alleged that they experienced a loss of braking capability that resulted in extended stopping distance, and/or illumination of the abs warning lamp. |
Consumer Complaints
Fail date | miles | occurences | Purchase date |
---|---|---|---|
SERVICE BRAKES, AIR | |||
05/20/1998 | 3 | 11/17/1997 | |
Brake appear to fail when front wheels hit a bump. | |||
SERVICE BRAKES, AIR - ANTILOCK | |||
01/01/2005 | 3 | 08/19/1997 | |
Truck's brakes seem to fail when travling at slow speed and applying brakes the pedal will lock up and make a reving sound and vehicle will not stop . contacted isuzu motor after the second instant and the recall was preformed on brakes but was told there is no problem . i do not fell safe driving this vehicle.*ak | |||
08/14/2003 | 3000 | 4 | 09/26/1997 |
Brakes failed to engage after pulling away from a stoplight at about 10-15 mph. the cars ahead stopped but my rodeo would not even with me literally standing on the brakes. they were non-responsive although the abs grinding took place. i recently had the vehicle in for the algorithm change, but noticed no difference. i initially called isuzu owner relations on 7/8/02 about the msn carpoint recall alert under nhtsa campaign number 021002000, noptification date 6/02/02, affecting 161,927 vehicles. isuzu owner relations personell vehemently denied there was any cause for alarm or action from isuzu. dealership and isuzu personnel denied any problem with brakes despite calls to isuzu owner relations and visits to the dealership. this is the 3rd accident (several other near accidents) with this same type of problem occurring resulting in an accident...this time the insurance company totaled the rodeo. i had become so skeptical of this vehicle that i refused to use it on boy scout or family outings. over the years, i have owned 10 vehicles, managed sales accounts in 11 states requiring me to drive appx 25 rental vehicles per year and yet had a spotless driving record ...from 1966 to 1998, before purchasing the rodeo...go figure. will isuzu now admit that there is a problem with the rodeo? please investigate.*ak | |||
02/20/2003 | |||
I called isuzu concerning recall number 02i002000 concerning the abs on the 1998 isuzu rodeo. i was informed that isuzu cannot send letters concerning recall because the government would not allow it yet. i called nhtsa and was given a number(1-800-959-3993) this number had been changed to 1-800-726-2700. i was told by this isuzu department that i needed to call customer relations at 1-800-255-6727, which is where i started!!! | |||
09/20/2000 | |||
Abs light has come on. due to the number of complaints and the open investigation (ea99-008) on the database i want to register this occurance. so far the brakes are working without abs. since warranty is over i will be taking it to an independant repair shop. | |||
10/13/1997 | |||
Anti lock brake system. | |||
SERVICE BRAKES, AIR - ANTILOCK - CONTROL UNIT/MODULE | |||
08/14/2003 | 3000 | 4 | 09/26/1997 |
Brakes failed to engage after pulling away from a stoplight at about 10-15 mph. the cars ahead stopped but my rodeo would not even with me literally standing on the brakes. they were non-responsive although the abs grinding took place. i recently had the vehicle in for the algorithm change, but noticed no difference. i initially called isuzu owner relations on 7/8/02 about the msn carpoint recall alert under nhtsa campaign number 021002000, noptification date 6/02/02, affecting 161,927 vehicles. isuzu owner relations personell vehemently denied there was any cause for alarm or action from isuzu. dealership and isuzu personnel denied any problem with brakes despite calls to isuzu owner relations and visits to the dealership. this is the 3rd accident (several other near accidents) with this same type of problem occurring resulting in an accident...this time the insurance company totaled the rodeo. i had become so skeptical of this vehicle that i refused to use it on boy scout or family outings. over the years, i have owned 10 vehicles, managed sales accounts in 11 states requiring me to drive appx 25 rental vehicles per year and yet had a spotless driving record ...from 1966 to 1998, before purchasing the rodeo...go figure. will isuzu now admit that there is a problem with the rodeo? please investigate.*ak | |||
02/11/2003 | 1 | 11/05/1998 | |
1998 isuzu rodeo does not stop properly ,especially on slick pavement. vehicle has exhibited this condition very sporadically since new. | |||
SERVICE BRAKES, AIR - DISC - ROTOR | |||
1 | |||
Vehicle brake rotor completely worn. | |||
SERVICE BRAKES, AIR - SUPPLY | |||
2 | 05/01/1998 | ||
2nd time studs and lug nuts defective. replacement required both times tired were rotated. dealer ackowledged problem and poor quality. said it was ongoing issue. was advised by dealer to contact isuzu.*ak | |||
SERVICE BRAKES, HYDRAULIC | |||
07/10/2009 | 105000 | 1 | |
I bought a 1998 2wd isuzu rodeo from a private party six months ago. since i bought it, i have been experiencing a loss of braking capability in some circumstance (every day, mainly when the engine is cold) that resulted in extended stopping distances and continuous illumination of the abs warning lamp. my garage mechanic told me this issue is due to the abs coil integrated module that needs to be replaced and that there is a recall on it for 1998-1999 isuzu rodeo vehicles (campaign no. 02i-002, campaign bulletin sb03-09-s001d, nhtsa campaign id number: 02i002000). i called two isuzu dealers but they told me there are no open recalls for my vehicle vin#. i don't understand why my 1998 isuzu rodeo is not included in this recall. *tr | |||
02/03/2009 | 107000 | ||
Tl*the contact owns a 1998 isuzu rodeo. while driving 15 mph, the abs indicator illuminated periodically. the brakes failed to stop the vehicle when driving over sand or gravel roads. the failure has occurred on four occasions. an independent mechanic inspected the vehicle, but was unable to determine the cause of the failure. the contact was advised that her vin was included in a recall; however, the manufacturer stated that the closest dealer was in connecticut. the contact lives in new york. a local isuzu dealer stated that they only repaired trucks and could not assist with the recall repair. the vin was confirmed as a part nhtsa campaign id number: 02i002000. the failure mileage was 107,000. | |||
03/17/2006 | 45000 | 1 | |
I have some very important issues pertaining to my 1998 isuzu rodeo. i read several blogs on a forum from other rodeo owners that have had some of the same problems that i have with mine. the biggest one is the abs system and the other is the fuel sending unit and gas gauge. these are two of the most reported problems but not the only ones. it seems that isuzu should be doing something to correct these and other problems associated with this vehicle. the abs has been addressed in some but not in others. although the gas gauge does not pose any real safety issues it is one that poses minor safety issue because of the possibility of running out of gas because of not knowing the correct amount of fuel in the car. *tr | |||
11/20/2004 | 95000 | 5 | |
A recall was issued for the brakes, however the problem never was repaired. *ak | |||
12/18/2003 | 37000 | 1 | |
While braking the pedal was hard and caused extended stopping distances. the dealer is aware of the problem but has not been resolved. please provide any additional information. *nm | |||
11/18/2003 | 53000 | 1 | |
While driving at 45 mph the consumers daughter (who was driving the vehicle alone) was changing lanes moving from the right to the left. soon after crossing the divider lines she noticed brake lights ahead. the consumer's daughter depressed the brakes and heard a grinding, popping sound and the brake pedal sank to the floor of the vehicle. a few moments passed, then the brakes functioned properly, but not in time. the consumer's daughter collided with the rear end of the vehicle in front. the air bags deployed causing slight injuries to the arms and stomach of the consumer's daughter. the daughter also slightly injured her right leg in the collision. police did arrive on the scene, but no one was cited. the manufacturer and the dealer were notified of the incident. *nlm | |||
10/29/2003 | 83949 | 1 | |
While driving 50 mph the brakes failed, causing, the vehicle to collide into a park bench. as a result, engine exploded. no fire reported. dealer stated the cause of the explosion was due to lack of oil in the vehicle. *ak | |||
80000 | 1 | ||
Consumer states when brake pedal is pressed pedal is hard, resulting in extended stopping distance. *ak | |||
06/24/2003 | |||
The abs light illuminated and stayed on . the brakes squeaked while driving. the dealer repaired the braakes but the light remained illuminated. *nlm | |||
05/22/2003 | 75440 | 03/20/2002 | |
Turning into parking lot, brakes did not stop vehicle - did not lock, did not skid, did not stop, resulting in the vehicle going into the building. | |||
04/24/2003 | 1 | ||
When the brakes were applied, the vehicle failed to stop. *jb | |||
04/04/2003 | |||
When the brakes were applied the pedal would go to the floor which caused the vehicle to have extended stopping distance. the dealer was notified. *nlm | |||
1 | |||
While driving under wet conditions at highway speed, the consumer loss control of the vehicle, when the brake pedal was applied, the pedal traveled to the floor, which resulted in an accident. *jb | |||
01/20/2003 | 100000 | 1 | |
The brakes made a cracking noise, and the vehicle continued to roll, when the brakes were applied, the consumer had to use emergency brake to stop the vehicle. *jb | |||
10/24/2002 | 1 | ||
When consumer attempted to apply the brakes, there was no response, which resulted in the emergency brake being applied, dealer was unable to duplicate the problem.ts *jb | |||
07/02/1998 | |||
Brake failure. | |||
SERVICE BRAKES, HYDRAULIC - ANTILOCK | |||
07/10/2009 | 105000 | 1 | |
I bought a 1998 2wd isuzu rodeo from a private party six months ago. since i bought it, i have been experiencing a loss of braking capability in some circumstance (every day, mainly when the engine is cold) that resulted in extended stopping distances and continuous illumination of the abs warning lamp. my garage mechanic told me this issue is due to the abs coil integrated module that needs to be replaced and that there is a recall on it for 1998-1999 isuzu rodeo vehicles (campaign no. 02i-002, campaign bulletin sb03-09-s001d, nhtsa campaign id number: 02i002000). i called two isuzu dealers but they told me there are no open recalls for my vehicle vin#. i don't understand why my 1998 isuzu rodeo is not included in this recall. *tr | |||
09/14/2007 | 1 | 10/18/1998 | |
1998 iszuzu rodeo. | |||
05/01/2004 | 70000 | 1 | 10/15/2002 |
Tl*the contact owns a 1998 isuzu rodeo. approximately three years ago, the contact received a recall notice for her antilock brake system. the mechanic would not perform the repair and stated that she needed to have her carburetor replaced. the repair would cost $2,000. the contact stated that she was involved in a crash approximately one year ago because her brakes locked. as a result, she crashed into the preceding vehicle while traveling 35 mph. the woman she struck stated that her neck was injured, but she did not file a claim. the contact's insurance agency paid for the damages. the contact had to get her vehicle totally rebuilt. a police report was filed. the engine size was unknown. the current mileage is 95,000 and failure mileage was 70,000. | |||
03/26/2006 | 8 | ||
Received recall notice for 98 isuzu rodeo contacted bell isuzu was told the part was not available at the time called back several times,was pulling in driveway brakes went all the way to the floor smashed into bedroom of roommate. called isuzu they replaced part then said it had nothing to do with my brakes. said they tested my brake fluid it was contaminated, and that i needed a new master cylinder. the part replaced directly affected the abs brake system from working properly they believe its not failure from this abs module, aligortham thank you for your time. *jb | |||
11/03/2005 | 101905 | 1 | |
Dt: thecontact was driving on the freeway and had blow out. she applied the brakes which were under manufacturer's recal 02i-002. there where no brakes. this resulted in a crash. the contact sustained injuries. *ak | |||
10/28/2005 | 108000 | 1 | 12/02/2002 |
Dt: the contact received recall 02i002000 last week. he called the dealership to set up an appointment to have the recall repairs done. after waiting a long time the dealership informed him that the parts were not available. the dealership told him to stay there until the truck arrived with the parts on it. finally, the dealership told him there was no truck coming with the parts on it. the contact's vehicle experiencing extended stopping distances in certain braking conditions as described in the recall, and was concerned about driving the car. the dealership did not offer him a rental car. the contact lived at least 50 miles away from the dealership.*ak | |||
12/13/2003 | 3549 | 1 | 07/01/2000 |
Dt: the contact received a manufacturer's recall 021-002 concerning abs brakes. when she contacted the dealer, they said they did not have the part. later, she scheduled an appointment and had to cancel it. when she called to reschedule the appointment they told her they had the part. before the appointment they had to reorder the part. before the repair could be made she was involved in an accident because of abs. failure. the contact was backing out of her driveway when the vehicle crashed into a fence. the contact sustained a, fracture d disc, and the root of her front tooth broke. there are medical records for the injuries. the vehicle was towed. the manufacturer said they would send someone to inspect the vehicle and did not do it. *ak | |||
07/15/2005 | 96000 | 1 | 02/15/2005 |
Dt: the consumer complained about an abs brake problem. the brakes did not hold. the abs light came on since june of 2005. on july 15, 2005 the brakes failed, causing consumer's vehicle to lightly hit another vehicle. no police report was taken.. when she took vehicle to the dealership , they cleaned the abs sensor because it was corroded. the abs light went off, and the brakes worked fine until september 29. 2005, and it almost caused another accident. after she took it to the dealer to be checked again, they said that it was a problem with the abs. *ak | |||
07/28/2005 | 105000 | 1 | 07/17/2001 |
My elderly father was driving the 1998 isuzu rodeo on i-78 west bound when the breaks failed. my father said it was as if the abs came on and prevented the brakes from working. the brake faliur resulted in a collision with the the car infront twice. at the time no injuries were reported however my father has experienced pain in his shoulders. after investigating how the brakes could fail on the internet i came to learn that this particular model of isuzu rodeo had been recalled due to abs brake faliur. this was the way i came to learn of the recall. to this date isuzu has never contacted me regarding this recall. i have made mulitple attempts to contact clode at isuzu customer relations his phone number is 1800 255 6727 ext 7417. we have exchanged phone messages but have not bee able to speak. i wish clode would make an effort to reach me. we made an appointment with buhler isuzu at vall homes nj to have the problem resolved. we took the car to this dealer today however they are unable to repair it due to lack of proper equipment on their part. i am filing this comlaint after making multiple good faith attempts to resolve this problem. i am hearby making it known that i will no longer be responisble for any consequences after this automobile leaves buhler isuzu with or with out the said repairs. the court date for this accident is on sept 22 05. | |||
04/01/2003 | 2 | 05/01/2002 | |
Nar 04/07/2003 mr the consumer was involved in 2 accidents within a six month period. in both cases the consumer was unable to stop at a reasonable distance which lead to both accidents. the consumer did receive a recall regarding the abs. *jb | |||
11/15/2004 | 152159 | 1 | |
While driving 50 mph a deer jumped out into the street consumer attempted to stop and brakes failed. vehicle collided with the deer, dragging it about 1500 feet. no report of airbag deployment. no injuries reported. *ak | |||
12/20/2003 | 66310 | 15 | 05/26/2002 |
When the brakes are applied it has a relatively long stopping distance compared to other vehicles. fortunately isuzu launched a recall campaign to address the problem and the abs module was replaced but the problem is persists. i wrote to the manufacturer informing them of the problem but i have heard from them since then. *jb | |||
09/19/2004 | 80000 | 20 | 11/18/1998 |
Failure of abs brake system, even though dealer fixed the problem via recall; fuel leak at hose and fuel pump connection; failure of fuel sending unit and fuel gauge.*ak | |||
09/10/2004 | 1 | ||
Consumer received nhtsa recall: 02i002000 concerning abs brakes. after having the computer replaced for the abs, and while driving 25 mph abs light appeared on the dashboard and remained on. vehicle was taken back to the dealer for inspection. the cause had not been determined. *ak | |||
08/31/2004 | 74000 | 1 | |
After abs recall 02i002000 repairs were performed the brake pedal went to the floor when depressed, resulting in extended stopping distance. dealership indicated that the recall part failed. *ak | |||
01/01/1901 | |||
Defective abs system which needed to be replaced. *ph the vehicle was taken to the dealer for repairs but they didn't have the parts available. *nm | |||
01/01/1901 | 1 | ||
Problems with abs system on 1998 isuzu rodeo.*mr the abs light illuminated and stayed on. the consumer received a recall notice for the abs (02i-002) and took the vehicle to the dealer to be repaired. when the consumer picked the vehicle up she noticed that the abs light was still on. the dealer failed to give the consumer an invoice indicating what was repaired/replaced. the consumer contacted the dealer who informed her that there was probably some other problem with the system and to bring the vehicle in for service. the consumer feels the problem should have been repaired the first time. *nm *jb | |||
01/19/2004 | 110467 | 1 | |
After recall repairs were done, the abs light remained on. *ph when the consumer asked why the light was still on the service rep said that the problem was with the sensors. the consumer refused additional work. months later the vehicle's brakes squeaked so bad that an independent shop refused to do the vehicle's state inspection. the consumer attributes the persistent squeaking with the initial abs safety recall 021-002. the consumer request that the manufacturer repair the sensors. *nm | |||
03/15/2004 | 1 | ||
Consumer stated that she received a recall note on abs brake failure in october 2003, and each time she called the isuzu dealer they tell her they still did not have the parts. dealer promised that they will call her back once parts arrived, but they never did so. consumer did not remember name, address or telephone number of this particular dealer. consumer indicated that she did not have any brake problem, but did want the recall taken care off. *ak | |||
60517 | 1 | ||
After having abs recall 02i002000 repairs done vehicle experienced brake failure, resulting in extended stopping distance. this only occurred while driving on snow or wet surfaces.*ak | |||
1 | |||
Recall 02i002000 concerning abs brake failure. consumer contacted the dealer in october 2003 for recall repairs. dealer indicated to consumer that the parts were not available. consumer recently contacted the dealer again, and dealer stated the parts were on national back order.*ak | |||
12/11/2003 | 5 | 1 | 12/05/1998 |
While going less than 5 miles per hour i had to apply my brakes suddenly. the brakes locked up and the car would not stop causing a crash into another vehicle. | |||
02/12/2003 | 1 | ||
Abs coil integrated module replacement.*mr while driving on the freeway at 35 mph the consumer noticed an accident ahead, when she tried to stop, the brakes completely locked up which caused her to rear end the person ahead of her. a few months later the consumer received information about a recall being issued for the brakes on the isuzu rodeo' s, the consumer hopes that isuzu can give financial assistance due to the defect. *cb (recall #02i0020000) *jb | |||
01/05/2004 | 1 | ||
Consumer received a recall letter concerning abs brake system failure on october 2003. dealer and manufacturer were cooperative and indicated there were no parts available. *ak there was no expected date of availability for the parts. *sc | |||
12/10/2003 | 107000 | 1 | 12/10/2003 |
It was raining. went to stop at the intersection of scott blvd and n. decatur going at approx 10 miles an hour. the brakes would not work. i released and tried again and there was nothing. hit the truck in front of me. the module for the abs was replaced in april 2003. | |||
12/21/2003 | 1 | ||
While driving at 25 mph anti lock brakes would not lock, causing the vehicle to hit a medal fence. consumer stated that the brakes experienced extended stopping distance. *ak | |||
12/11/2003 | 1 | ||
Consumer received a recall notice on november 5/2003 concerning abs brakes. the abs problem on certain sport utility vehicles that were equipped with an anti-lock braking system (abs), the vehicles could experience extended stopping distances in certain types of braking events. dealer stated the recall was on back order. one must wait, we didn't' have the part yet. but on december 11, 2003 consumer had a collision due to brake failure. *ak | |||
1 | |||
Consumer was unable to have abs recall 02i002000 repairs performed due to the parts being on back order. manufacturer provided no assistance, they just indicated that this was an improvement campaign and not a safety campaign.*ak | |||
11/26/2003 | 1 | ||
The consumer will provide information on the abs and problem with a local dealer. *nlm | |||
11/25/2003 | 1 | ||
While driving 55 mph the abs brake light illuminated on the dash and the brake pedal went down to the floor. the driver took the vehicle to the dealer for analysis. the technician could not duplicate the problem. *nlm | |||
11/17/2003 | 1 | ||
Consumer received a recall notice for abs brakes. took vehicle to dealer for recall repairs, and since then has had abs brake problems. however, dealer refused to do additional repairs. *ak | |||
1 | |||
Dealership was unable to perform recall 02i002000 repairs concerning abs brakes because they were unable to get the parts from the manufacturer, and manufacturer was unable to provide a proper explanation of why the parts were not available to the dealership. *ak | |||
10/24/2003 | 1 | ||
Consumer received recal 02i002000 concerning abs brake failure. consumer contacted the dealer, who indicated that the parts would not be available until february 2004.*ak | |||
11/03/2003 | 1 | ||
Vehicle was taken to the dealer for recall 02i002000 repairs concerning abs failure. dealer kept the vehicle all day and did not do the recall repairs because the parts were unavailable. also, the dealer wanted to charge the consumer for doing a diagnostic test which found a problem with the rear brakes.*ak *tt *jb | |||
10/31/2003 | 50000 | 1 | |
While driving at 50 mph, driver applied the brakes and they failed. vehicle took longer to stop, and collided with the guard rail. after the accident consumer called the dealer to verify if there was any recall on vehicle. dealer denied it . 10 months after the accident, consumer received a recall nhtsa letter 02i002000 concerning abs brake failure. *ak | |||
10/30/2003 | 58000 | 1 | |
While driving 25 mph consumer avoided hitting a flock of ducks. upon applying the brakes brake pedal went to the floor, and vehicle took longer to stop. vehicle collided with a stop sign, and experienced $5,500 damage. *ak | |||
10/24/2003 | 146000 | 1 | |
The defect stated in abs nhtsa recall campaign 02i002000 ccurred prior to consumer receiving the recall letter. as a result, vehicle experienced abs failure which resulted in an accident.*ak | |||
10/13/2003 | 6599 | 5 | |
Whenever abs brakes were applied brake pedal would go to the floor. this caused extended stopping distance. consumer took vehicle to dealership, and mechanic could not duplicate or resolve the brake problem.*ak | |||
4 | 07/01/1998 | ||
The anti-lock brakes failed to properly engage allowing the car to roll forward. *mr there were several incidents where on slow stops, the anti-lock brakes failed to properly engage and allowed the vehicle to roll forward. the problem was intermittent. the master cylinder was replaced, however, the problem recurred. refer to recall#02i002000. the consumer was told that there was no existing recall. *scc *jb | |||
4 | 06/30/1998 | ||
Brake failure occurred while driving at 10 mph. *mr the consumer applied the brakes with regular soft pedal braking when the vehicle slid forward beyond the normal braking point. the consumer had to brake three vehicle lengths ahead. the abs light was intermittent. the abs light came on when the consumer had to brake on any bumpy or uneven street, flat surface, or downgrade. the consumer slid into the bumper of another vehicle that stopped unexpectedly. *scc | |||
1 | |||
About a year ago consumer received recall notice# 02i002000 concerning abs. there was no problem with the abs. dealer made the recall repairs, and now the abs light has been flashing on intermittently.*ak | |||
04/16/1999 | 7 | 07/17/1998 | |
1998 isuzu rodeo experienced brake failure. *mr the brakes were intermittent. the brake pedal would go to the floor and lock up. a few days later the abs light had come on. the problem was diagnosed as a rear brake sensor and was replaced. the molding on the driver door was loose, the latch on the console had broken, the sunvisor on the passenger side had fallen down, and the center caps on the front wheels had pitted. the consumer requested a buy back and or trade in. *scc *jb | |||
1 | |||
When the abs warning light comes on and brakes are appiled there is a loud noise. the brake pads are not worn.*ak | |||
07/06/2003 | 50000 | 1 | 08/20/1998 |
Vehicle was parked and unoccupied in front of owner's home - in first gear with parking break engaged and wheels turned toward the road. there was a clicking noise under the hood and, although parking break was applied, vehicle's wheels were rotating, as if the vehicle was driving itself. vehicle proceeded to hit another vehicle parked 6+ feet in front of it. when it hit the other vehicle it pushed and held the vehicle's frame about 3 inches forward. the engine started smoking and continued clicking. fire and police were called. when fire and police arrived, firemen removed battery cables to vehicle and pushed vehicle back to the side of the road and the vehicle's body (vehicle that had been hit) swung back over it's frame. this very dangerous occurrence was witnessed by the woman whose vehicle had been hit. also, abs system on the isuzu never worked and the four-wheel drive most times didn't engage or disengage as it should have. 0n 7/9/2003 the dealer stated the anti theft module failed which caused the vehicle to start up. *ak | |||
06/25/2003 | 1 | 05/01/1998 | |
While driving, the brakes failed, which caused the to experience extended stopping distance. dealer notified. *ak *ts also the abs light illuminated when the incident occurred. *jb | |||
03/15/1998 | 100 | 01/21/1998 | |
Anti-lock brakes do not work properly when one tire hits a slippery surface causing extended braking distance. *nlm | |||
1 | |||
Consumer received a recall notice # 02i002000 subject: abs. consumer called the dealer and made an appointment. when the consumer got to the dealer, there were no parts available. the dealer said they would call when the parts became available. it has been two weeks and the consumer has not received a call.*ak | |||
06/18/2003 | 1 | ||
While pulling inside of the parking lot applied brakes and ran into the vehicle from behind. brake pedal did not hold, and went all the way down to the floor. *ak | |||
1 | |||
Abs light is flashing constantly, and there is a delay in stopping when brakes are applied. *ak | |||
02/28/2002 | 76882 | 1 | |
If i am decelerating and the front tires hit a bump or dip in the roadway, i lose the brake pedal. i have been told that this is an abs activation, however, i find it hard to believe this is normal abs operation. when i rear ended the vehicle, i was decelerating and rolled over a depressed manhole in the roadway causing the braking failure. i can reproduce the failure anytime. i have had isuzu dealers test drive the vehicle, and they tell me this is normal abs activation. i have driver four-wheel anti-lock break vehicle's and have never experienced this before. it has caused me to roll through red lights on numerous occasions due to rolling over road way defects while breaking. if abs is suppose to shorten my breaking distance in lieu of a skid condition, i'd rather go into a skid. at least then i will have some control over my breaking. please help... i seriously doubt this is normal for abs. *jb ***dimsii ivoq entry posted after 12/12/02 cut-over to artemis*****770768 | |||
1 | |||
Under certain conditions the abs failed to stop the vehicle. *ak. after 5 years a recall was issued, and the vehicle was repaired. *jb | |||
04/21/2003 | 1 | 08/01/1998 | |
The consumer has made several appointments to have the abs recall (02 i 002 000) fixed but the parts are still not available. *nlm | |||
04/18/2003 | |||
The vehicle was recalled for the abs brakes. the dealer stated that they would not had the recall parts for 3-4 weeks. * nlm | |||
03/11/2003 | 1 | ||
Letter from d. grimes (va) wanted response to his inquiry on a recall intiated by nhtsa concerning abs brake failure on 1998, isuzu, rodeo; recall 02i002000; no record of e-mail in system; reply to richmond, va ofc, reference david c. grimes, dot/#2003-2228. *ak | |||
01/14/2002 | |||
Brakes failed when trying to stop on a freeway, ran into another car. *nlm | |||
01/01/1901 | 1 | ||
Letter from d. grimes (va) re recall initiated by nhtsa on 1988 isuzu, rodeo, recall 01i002000. reply to norfolk, va ofc, dot/#2002-2203. consumer's vehicle experienced the same anti lock brake defect as stated in recall #02i002000. *jb. *ak *cb | |||
Abs failure. | |||
03/26/2003 | 1 | ||
No parts were available. regarding recall#02i002000 abs. *jb | |||
01/12/2003 | 81000 | 25 | 02/10/1998 |
Antilock brake systems activates on dry pavement during normal braking, unable to safely stop vehicle. dealer reports abs module replaced in june 1998 but problem has continued. also, abs warning system light stays on intermitently. | |||
08/24/2002 | 1 | ||
Abs light came on, driving 35 mph could not stop suddenly and slid into another car causing $2700 worth of damage to my car and insurance had lapsed had to pay out of pocket. fuel gauge always shows less than really is even when full. catalictic converter is always rattling. dt | |||
08/26/2002 | 1 | 06/01/2002 | |
Wheels locked, causing loss of steering, and allowing vehicle to slide off roadway into shallow ditch. *ak | |||
07/24/2002 | 10 | 07/01/2001 | |
The brakes seem to go out when applied over bumpy roadways. the problem seems to happen at many different speeds and this has happened numerous times. this has occurred with my wife driving as well as when i am driving. we have had the car checked at two separate brake specialist shops, and at a honda dealer when we had the 100,000 mile tune-up and they said the brakes were fine. we have not had an accident yet, but the fact that so many other people have the same problem worries me and makes me think my wife should not be driving this vehicle.*ak | |||
07/10/2002 | 100 | 08/01/2001 | |
No summary listed for above vehicle. *ak | |||
06/01/2002 | 4 | 11/01/2099 | |
Abs system is engaging after vehicle has stopped which causes vehicle to lurch forward. over $1500 total brake repair so far on this vehicle and it still won't stop properly. *ak | |||
08/01/2001 | 1 | 03/01/1998 | |
Sway bar broke off while consumer was driving. contacted dealer, and dealer was not willing to do anything. *ak consumer states vehicle is jerking backwards while driving. dealer could not find anything, however problem persist. abs light comes on intermittently. dealer could not find a problem. *tt | |||
12/11/2001 | 2 | 12/01/2098 | |
2 days out of warranty a second abs sensor failed on my car. i had just had a rear one replaced the week before. the dealership said oh well it is out of warranty now but we can look at it for you but that i would have to pay. i noticed that there have been several complaints for this. i am trying to contact the manufacturer to see if they will take care of this. *ak | |||
02/01/2002 | |||
When stopping at a light brake pedal would give out and hit the floor. took vehicle to dealer, and they replaced abs module. currently, brakes get hard at a stop. took vehicle back to dealer, and they replaced master cylinder. please provide any further information. *ak | |||
05/05/1999 | 30 | 07/01/1998 | |
No summary listed for above vehicle. *ak | |||
01/08/2002 | 50 | 08/01/1998 | |
The anti-lock brake system does not operate properly. this was first looked into at the 7500 mile service with no problem found. the car now has 67000 miles with the problem still occuring. there has been one accident caused by problem with many close calls. the vehicle is very unsafe to drive. without warning the brake pedal will kick back at the driver and the car will lose all braking power. the dealership says this is normal operation for the abs. i've driven many cars with abs, and they all stop when the abs is engaged. this rodeo loses all pressure and just glides forward. so far they have replaced a speed sensor and the wiring harness that goes to the rear of the car. isuzu says they have made a new harness because the old one was too short and would break easily. but, there is no recall on it. the sensor and harness were replaced two weeks ago, but the problem still persists. please help us with getting our vehicle fixed properly before there is a major accident caused by it. *ak | |||
12/16/2001 | |||
While driving at 5 mph and upon applying brake pedal brakes failed to respond, causing extended stopping distance. consumer has contacted dealer, who determined that wire harness connected to abs brakes shorted out the speed sensor. dealer has replaced the wire harness at 20000 miles. please provide any further details. *ak | |||
12/14/2001 | |||
While driving about 20mph and applying brakes vehicle did not stop. felt like brakes did not engage. consumer lost control of vehicle. when hitting a bump or pothole brakes went to floor. this happened intermittently. please add vin. *ak | |||
10/08/2001 | 05/01/1998 | ||
I had all preventive maintenance and a lot of work done on brakes in the past few weeks at the dealership. suddenly, a week and a half after the last repair, this problem comes from nowhere. of course, it's an additional repair with additional costs. something is not right. this care has been maintained and very well taken care of for the past 3 years. *ak | |||
3 | |||
Whenever brakes are applied vehicle fails to stop properly. had taken vehicle to dealership and was informed that no problem existed with brakes in 1999. after moving to another state experienced the same problem. took to another dealership, and informed consumer brakes were not grabbing like they should. mechanic replaced pads and rotors in the rear of vehicle. problem of non stopping still exists.*ak | |||
10/01/1998 | |||
Rear brakes have been serviced 7 times, replacement of shoes each time. abs light will not go out, brakes have failed twice at very low speed during stopping. *ak | |||
Brake pads and rotors are wearing excessively, front and rear rotors have rusted prematurely. also, states when brakes are applied it is extremely difficult to stop, driver has to downshift to stop the vehicle. please give any further details.*ak | |||
06/01/2001 | 1 | ||
When attepmting to stop and upon applying brakes abs brakes failed, causing extended stopping distance which resulted in a rearend collision, impact speed 15 mph. consumer has contacted dealer. please provide any further details. *ak isuzu has denied the problem, consumer states every time vehicle hits a bump, she temporarily loses brake control. *slc | |||
02/14/2001 | 2 | 06/01/1998 | |
Abs brakes skipped, brakes never really engaged...vehicle never slowed down. *ak | |||
04/03/2001 | 1 | 02/01/1999 | |
I applied my brakes to stop and abs kicked in and prevented the vehicle from stopping and i don't believe even slowed the vehicle much. the conditions were dry and sunny, if abs did not activiate, and i feel it should not have, an accident would have been avoided. *ak | |||
1 | 12/01/1999 | ||
Ea99008; when driving over bump or pot hole brakes will fail. after going over bump and reapplying brakes vehicle will eventually stop.*ak consumer states there have almost been numerous accidents because of this problem, especially when going down a driveway or a hill, consumer has contacted manufacturer and was told, that is how the anti-lock system works on this vehicle. *jb | |||
01/30/2001 | |||
While driving on a slight incline at 10mph applied brakes and pedal went to floor. consumer hit vehicle in front, causing . $ 2000.00 damage. *ak | |||
1 | 12/18/1998 | ||
While traveling over any bump or sticky surfaces and depressing the brake pedal, vehicle goes into exceeding speed while brakes are being applied and it takes longer than expected to come to a complete stop. *ak the vehicle surge when brakes are applied. the dealer could not duplicate the problem, but the consumer is concerned about safety of driving this vehicle. *yh | |||
01/21/2001 | 1 | 01/01/2001 | |
While driving on a semi-bumpy paved road i attempted to make a quick stop from about 20mph. as i attempted to stop the abs brakes appeared to engage (had abs on my previous car) then totally failed and i rolled out into the intersection. went about 10-15 feet without any braking power. if cars would have been passing through intersection or had been in front of me - would have caused an accident.*ak | |||
12/01/2000 | 7 | ||
Low speed on rough/slick surface, abs slips, pedal to floor and makes ca-ca-ca sound. *ak | |||
07/07/2000 | 12 | 08/01/1998 | |
Brakes failed attempting to stop at sign while traveling over bumps in road/pedal went to floor/vehicle seemed to accelerate when brakes went to floor rather than slow down. *ak | |||
09/20/2000 | |||
Abs stopped working. dealer determined a faulty wiring harness and replaced it (part # 8-97233-422-0). *ak | |||
10 | 03/01/1999 | ||
Braking discontinues and pedal goes soft when a bump is hit at any speed, has happened numerous times, check engine light on due to faulty fuel sensor | |||
09/13/2000 | |||
While traveling at highway speed of 40 mph on a semi wet road, applied brakes to slowdown, and all of sudden vehicle spun out of control and hit medium strip; spun around again and hit the medium strip on the right side of vehicle. driver received back and neck injuries. dealer/manufacturer notified. please feel free to provide any further details. *ak | |||
5 | 01/01/1999 | ||
3 or more incidents of excessive stopping distance when abs engaged almost resulting in an accident . also strongly believe abs should not of engage under these conditions. system to sensitive. *ak, | |||
2 | 03/01/1998 | ||
Abs problem previously corrected by dealer when vehical new, but now abs light comes on constantly and car is out of warranty. i think isusu should take care of abs problem. have seen and heard of lots of complaints about abs, so there is obviously an abs defect. *ak | |||
09/18/2000 | 100 | 02/01/1998 | |
No summary listed for above vehicle. *ak | |||
03/01/1999 | |||
No summary listed for abov evehicle. *ak( dot number: tire size: 15 ) | |||
When brake pedal was applied it went to the floor. brakes responded late. after reapplying brakes with two feet, vehicle began to slow down. dealer has been contacted. *ak | |||
08/02/2000 | 0 | ||
Consumer was traveling abour 35mph on main street and was approaching stop light, went to apply his brakes, and there was no response. abs brake system light came on dash panel. consumer slammed on brakes, and vehicle continued to roll.then, he apllied emergency brake to bring vehicle to a complete stop. consumer took vehicle to the dealership. dealership had the vehicle three days. mechanic could not find the cause. *ak | |||
07/17/2000 | 1 | 12/16/1998 | |
While preparing to stop for a traffic light at about 30 mph, light turned red and consumer pressed on brakes. but, vehicle did not stop. pedal was pressed to all the way to the floor and the vehicle kept going. as consumer repressed the brake pedal vehicle eventually stopped. the defect did not give consumer control of vehicle which could have been involved in an accident. vehicle never gave a warning signal.*ak | |||
05/13/2000 | 1 | 06/25/1998 | |
While applying brakes brake pedal went to the floor. had no brakes. vehicle lunged forward suddenly & hit another vehicle. took vehicle to dealer & was informed that abs system was the cause, and dealer could not repair the problem.*ak the consumer claims defective abs was the cause of the accident that occured. *yh | |||
05/22/2000 | 7 | 04/01/1998 | |
When applying the brakes, the abs system seems to engage prematurely at about 35-40 mph and if the vehicle hits any type of bump when in the process of slowing down, one cannot stop the vehicle until the abs system brings the vehicle to a stop. i was advised by the dealer that the abs system was designed to help maintain steering control during braking and prevent skidding and is functioning properly. this vehicle is unsafe to drive! my wife has encountered the problem twice and will not drive the vehicle. my children and grandchild are not allowed to ride in or drive the vehicle because of our concern for their safety. what can be done to rectif this problem? *ak | |||
02/01/2000 | 6 | 04/01/1998 | |
Abs system prevents stopping vehicle after hitting any bump when applying brakes at about 40 mph. dealer says that everything is working properly. problem still exists. *ml | |||
04/15/1999 | 3 | 05/01/1998 | |
In october of 1998 i had an incident where i needed to make a left turn on a residential street. when i braked to slow down, i couldn't stop and went through intersection. luckily no cars were around. i was very confused because suddenly the brakes seemed fine. i told people about this and just figured it was a strange incident. in april of 1999 i was driving with a friend and traveling about 35mph when a tractor trailer stopped in front of me. i went to stop and had the same feeling as before when i had no brakes. i literally drove into the back of the semi at 35 mph. i couldn't go to my right or left because of cars. the car had $8,000 worth of damage. i told the body shop that the brakes went out. they checked and found nothing. i called isuzu and they said there were no complaints. again, this was very confusing. i know i had no brakes and all of a sudden they were ok. the last incident happened in march of 2000. i was driving alone at about 30 mph and a car slowed in front of me. i hit the brakes and you guessed it, no brakes. i turned right over a curb and hit a tree slightly. this car is very dangerous to say the least. someone will be killed! i told a friend i haven't seen in a while about this and he said he saw a report on nbc about cars that had suddenly lost their brakes. i checked on the internet and found the exact same situation happened to many others with the 1998-99 rodeo. i was so excited i couldn't sleep. finally, i figured this would be taken care of. i called nbc and they said to file a complaint with you. this is a major problem that need to be corrected! please do something about this. it's not a coincidence. i've driven over 1,500,000 miles and have owned as many as 50 cars in my life. i know what i'm talking about. i'm afraid to put my kids in the car. please call for as much info as possible. thank you. *ak | |||
09/01/1997 | |||
When braking and upon encountering a bump brakes released, then locked up when vehicle toucheed the ground again. this caused vehicle to slide into intersections on several occasions, once resulting in an accident. *ak | |||
11/06/1998 | 3 | 04/01/1998 | |
Consumer attempted to step on brakes as he was approaching a stop sign and vehicle did not stop. rearended vehicle in front. upon impact, air bags did not deploy. driver sustained injuries. *ak | |||
Upon braking on rough surface abs brakes fail to operate. *ak | |||
02/01/2000 | 1 | 09/01/1998 | |
While applying brakes at 20mph, heard a growling sound from under hood in front of driver's position. brake pedal went down and felt like vehicle would not stop. reported to dealer. dealer says brakes o.k. owner says brakes feel spongy and feel like they will not stop vehicle if needed in an emergency. *ak | |||
25 | 04/01/1999 | ||
75% of the time when i attempt to stop during a rain storm, when driving on bumps or stopping abruptly my brakes slip. it feels like i'm pressing directly on the metal. when i pump the brakes it goes back to normal. i expressed this problem to a local isuzu dealer when getting my 30,000 mile service. he chekced it out and found that the brakes were in good shape. he could not find any reason for the brakes to disfunction. i took his word for it until it happened again when i tried to brake while driving over a rail road track and the brakes slipped again. i, as the main dirver of this vehicle, have gotten used to this and use extreme caution whenever i am in any of the 3 situations mentioned. unfortunately, i am not the only driver and it is a concern of mine that another person driving my car when this happens may not know how to react and get themselves into a serious, possibly fatal, accident. besides my local dealer, which hasn't been much help, i don't know where else to go to get this problem fixed. please help if you can. thank you. *ak | |||
03/26/2000 | 1 | 07/31/1998 | |
Brakes are an ongoing problem. brakes intermittently work on any type surface. they release at anytime for a split second. car just keeps on moving for a split second. *ak seems to happen on bumpy or wet roads. dealer replaced some wiring harness on brakes in rear of the vehicle that they said was too short. brakes are working so far. *yh | |||
11/01/1998 | |||
While driving over any bumps braking system malfunctioned, causing no braking ability, and resulting in a crash. also, in wet conditions vehicle wandered which caused a loss of vehicle control. dealer could not determine the cause of the problem. please provide further information. *ak | |||
12/15/1999 | 03/01/1998 | ||
While driving consumer started to apply brakes, and hit a small pothole. brakes made a grinding noise, pedal went straight to the floor and vehicle didn't respond. hit car in front. contacted dealer, said nothing was wrong with brakes. this happened again 27 jan 00. anytime while driving on an uneven surface the brakes works intermittently. just had the tires replaced. *ak | |||
10/01/1998 | 6 | 06/01/1998 | |
Ea99008, intermittently while the occupant pressed the brakes there was no braking ability. then, occupant pressed the brake pedal again, and the braking system activated. dealer could not determine the cause of the problem. other repair shop found air in the abs system to be causing the problem. *ak *ml | |||
07/03/1998 | 16 | 07/01/1998 | |
No summary provided by consumer | |||
12/21/1999 | |||
When the brakes are applied on wet or icy pavements rear wheels spin, resulting in extended stopping distance. dealer has been notified. prior to this incident the vehicle was involved in a collision due to the vehicle experiencing extended stopping distance. *ak | |||
11/30/1999 | 2 | 05/01/1998 | |
Brakes failed pulling into parking space, jumped curb, brakes locked, vehicle struck building; brakes failed at high speed on highway service road, swerved vehicle onto curb to avoid collision; brakes release when driving over bumps in road at all speeds (e.g., railroad tracks, potholes, speed bumps); recreated this problem with isuzu service manager in the vehicle; brakes have constant metal to metal sound; vehicle lurches when air conditioner compressor starts - brake pedal falls; isuzu has stated many times that brakes meet specs; rear drums have been replaced; brake pedal has been recalibrated; problems persist; consumer safety has been grossly compromised without resolving the issue. *ak | |||
12/09/1999 | 7 | 11/01/1997 | |
Brakes go to the floor on normal conditions and at any speed making a trrraacckk sound and stopping a few feet away. this has happened 7 times ,luckily no car has been near and i've also pulled onto the sidewalk. taken to dealer 3 times even have left a mechanic take car to his house for 3 days to check the brakes on the road and i've rented a car and they keep saying the brakes are perfect, no problem. i fear for my life & others that ride with me or any other car on the street is in jeopardy. i 'm driving with one hand on the wheel and the other on the emergency brakes (that works because they've been used). please if you can help me i would really be grateful.*ak | |||
11/01/1999 | 10 | 06/01/1999 | |
When i noticed i am about to approach a pothole or if i hit a bump in the road, or sometimes a speed bump, the brakes will skip. the truck would be kicked forward, almost hitting drivers that are in front of me. *ak | |||
12/01/1997 | 5 | 10/01/1997 | |
Very dissatisfied with vehicle, feel extremely endangered in driving vehicle | |||
11/16/1998 | |||
Rear abs brakes operate erratically. would cause extended stopping distance when applied. the brake pedal would jump quickly. brakes would make clunking noises after stopping. the pavement would be dry. been to dealer & informed by mechanic the abs actuator had to be replaced. *ak | |||
09/01/1999 | |||
While pulling out of a parking lot vehicle accelerated when taking off on a hill. consumer applied the brakes, they went straight to the floorboard, causing the consumer to rear end another vehicle. *ak | |||
2 | |||
Abs brake system failed twice. *yc | |||
03/01/1999 | |||
Going over railroad tracks and vehicle in front stopped. consumer went to apply brakes and brakes failed, resulting in an accident. *ak | |||
01/01/1999 | |||
Ea99008, abs braking system; when braking during normal braking, on regular road condtions , at slow speed, the truck doesn't stop and travels as though it is on ice. the dealer was not able to find out what caused the problem with the brakes. owner has not experienced any problem after the remote starter was disengaged. please provide further details. *ak | |||
07/25/1999 | 3 | 12/01/1998 | |
I depressed the break petal and it would not go in. i had no breakes at all. i used the hand break and pulled to the side of the road. i tried again to activat the breaks but the petal would not go in. i turned off the key and immediantly the break petal went in and i had breaks. i started the car up again and knowing the dangerous problem i kept my distance from other vehicles and worked my way home. the same thing happened to me two more times. each time the same thing happened. i lost brakes completely and had to turn off the key befor i could depress the brakes again. i am very concerned. this could have resulted in a serious accident and others may be at risk if the probem also exists with there rodeo. | |||
10 | 09/01/1998 | ||
Brakes grind and fail completely when abs system engages. abs engages when vehicle hits bumps during braking and the brakes fail. this happens almost daily at any speed and has caused several near collisions.the dealer will not acknowledge the problem and would not contact the manufacturer. | |||
06/24/1999 | 6 | 07/01/1998 | |
At least six times in the past year my braking system has failed to work properly. at speeds of 30 miles per hour and less i've had to brake suddenly. the brakes will grab for a second, release quicky, then grab again. after the third time this happened, i ask the dealer to check the brakes. they found no problems. this problem has not gone away. the last time this occurred was on july 4, 1999. the symptons the brakes are experiencing are similiar to those i have read about with the gm cars. *ak | |||
09/01/1998 | |||
No summary listed for this vehicle. *ak | |||
03/15/1999 | 8 | 07/01/1998 | |
I was turning into a mall off a freeway access road. i slowed down for the turn and as the vehicle turned, there was a bump in the road. i applied the brakes and did not feel any feedback from the pedal. it completely sank to the floor. there was a noise which sounded something like a trrrrk with clicking as the pedal sank to the floor. i got the feeling that i had no brakes at all and thought that i would surely hit the road divider as i was turning into the mall. about seconds later the vehicle seemed to slowly respond to the brakes. this had happened several times earlier. always on some kind of a bump and at quite a low speed (10-20mph). same problem -- loss of brakes, pedal sank to the floor and the trrrrk and clicking sound from the brake pedal area. i'd reported this to the dealership when i had the truck in for some accessory problems (cup holder did not close), buzzing from tape player when engine was on (never fixed either). they told me that the abs system was tested and was within the vehicle specifications. it is an extremely unnerving experience everytime this happens. i've had the vehicle for about 10 months now and this has happened about 8-9 times. i'd bought the vehicle from san antonio but i get it serviced at the dealership in austin where i live. the dealership is covert isuzu the number is 512 583 3010. *ak | |||
04/19/1999 | |||
Consumer was driving approximately 40-45mph when she began to smell gasoline. the front wheel of driver side started to feel like it was turning to the right. vehicle began skidding. driver applied brakes, but brakes failed to stop vehicle. consumer lost control of wheel and crashed into the gaurdrail, vehicle was towed. *ak | |||
04/19/1999 | 4 | 03/01/1998 | |
Abs failed. when applying brakes at low speed while crossing rough pavement, abs/brakes didn't function for several feet. *ak | |||
01/12/1999 | 4 | ||
While driving tried to stop, but vehicle didn't stop until a few feet away from where consumer had applied the brakes. *ak | |||
01/08/1999 | 1 | 12/01/1997 | |
Brakes failed on wet pavement with front wheels skipping. *ak | |||
10/25/1998 | |||
When depessing the brake pedal, the vehicle did not stop. this happened without warning. driver was able to put truck in neutral, then in park while turning into a parking lot. there was no inclement weather when this happened. the problem has been reported to the manufacturer. | |||
12/13/1997 | |||
Abs brake failure. | |||
03/11/1999 | 2 | 10/01/1998 | |
I was traveling down the road and when i hit the brakes the vehicle did not respond. i took it to meineke for an ispection and they reported a failure in the master cylinder. when i brought it to the dealer, they claimed the brake pedal should be able to touch the floor and then proceeded with no response. i tried to contact isuzu customer relations and they would not talk to me. *ak | |||
03/10/1999 | 5 | 02/01/1998 | |
At any speed if i were to apply the brakes with normal pedal pressure while one or both front wheels is traveling over an imperfection in the road or small hole the brakes seem to fail to the point that the vehicle seems to have no brakes. the vehicle feels like it just loses the effect of the brakes. the pedal feel is that it seems to move a little close to the floor and the feeling of the abs pulsating is felt during the instance but the vehicle isnt proceeding to slow down until the wheel(s) stop bouncing or revbounding from the imperfection in the road then the vehicle tends to slow down. in one instance i let up on the brake pedal and re-applied it firmer and the front wheels locked up. the pedal never seems to go to the floor as in a loss of pressure it just gets sponging and you feel the abs pulsating thru the pedal and the vehicle doesnt slow down. i am just thankfull that this hasnt led to my family and i getting into an accident. thank you for your time scott. | |||
02/06/1999 | |||
While driving at 60 mph, steering wheel locked, and abs brakes did not work at all. frontal impact into railing, and airbags did not deploy. dealer contacted and was not aware of the problem. cannot remedy the vehicle. problem still exists. provide further information. *ak | |||
When applying the abs brakes on wet or dry pavement the pedal goes to the floor, causing extended stopping distance. please give any further details. *ak | |||
08/01/1998 | 07/02/1998 | ||
Pulled into a parking lot and pulled up to wooden parking stopper. attempted to stop by applying the brakes, vehicle would not stop. vehicle crashed into wooden structure. no one was injured, vehicle sustained undetermined amount of damage. | |||
01/01/1998 | 100 | 12/01/1997 | |
The brakes have failed many/many times. i have had the vehicle in the dealership over 10 times. they have brought in an isuzu design engineer and a zone manager. they couldn't find anything, and said that they officially give up. they told me they do not believe that there are problems with the brakes, and that they don't know why i'm having the problems as others are not. they think it is just my lack of understanding about how abs systems work - despite the fact that i have driven vehicles with abs for many years. the zone manager was quite patronizing. the dealership has tried to be helpful, but i believe that they have been limited due to lack of information from isuzu. please contact me asap as this is a serious safety hazard. i would like to know what the status of the investigation is. thank you. karen. *ak | |||
04/14/1998 | 5 | 03/01/1998 | |
No summary | |||
When applying the brakes pedal stays up and vehicle does not stop. owner hit another vehicle because of abs not working properly. after crash, the abs warning light came on. dealer said there was nothing wrong. *ak | |||
07/01/1998 | |||
Pe98051; intermittently while driving braking system malfunctioned and vibrated, almost causing an accident. been to dealer several times, dealer cannot determine the problem. please provide further information. *ak | |||
01/12/1999 | 1 | 10/01/1998 | |
No summary listed for this vehicle. *ak | |||
01/15/1999 | 2 | 09/01/1998 | |
My brakes have failed on two occasions. i took the vehicle to the dealer, where i purchased it. before inspecting the vehicle, the mechanic assigned to the vehicle suggested it was operating as expected or designed and attributed the incidents to wheel hop. work on the vehicle was not completed on the 2nd, and the vehicle has not been returned to me at this time. the first incident occurred shortly after i purchased the vehicle. i was at stop sign in a mall parking lot, at the top of a short, steep incline. after i pulled away from the stop sign, i pushed in the clutch, applied light braking pressure as the vehicle begin rolling down the incline, preparing to make a sharp right hand turn at the bottom of the hill. as the vehicle approached the crest of the incline, the right front tire hit a pothole at slow speed. the brake pedal dropped significantly, the brakes felt like they released without vibration or pulsing, and the vehicle rolled approximately one and one-half car lengths before stopping at the bottom of the incline. the second incident happened several weeks ago, after i had been in stop and go traffic for approximately forty minutes, with the headlights, air-conditioning and stereo on. i was creeping along in first or second gear, down an incline overpass, i pushed in the clutch, applied light braking pressure. as the cars stacked up to get off the ramp. my rodeo rolled over an expansion joint, at slow speed, the brake pedal dropped significantly, the brakes felt like they released without vibration or pulsing and the vehicle rolled freely about 3 to 5 ft before coming to a stop. *ak | |||
01/19/1999 | 2 | 03/01/1998 | |
Brakes malfunctioned at low speed, strong vibration from brakes, but it could not completely stop. ran into another car ,created car damage and body injury. *ak | |||
06/28/1998 | 2 | 03/01/1998 | |
Brakes malfunctioning when prepared to stop. strong vibration from brakes, but never stopped. dealer's report worked as designed. no problem. *ak | |||
07/01/1998 | 1 | 04/01/1998 | |
Abs brakes failed prior to recall notice resulting in vehicle collision. | |||
10/01/1998 | 02/01/1998 | ||
No summary included. *ak | |||
06/01/1998 | 06/01/1998 | ||
Brakes squeal anytime they are applied. gas pedal broke off. gas pedal is a piece of flimsy plastic that snaps on and is very dangerous. car vibrates at all speeds since purchase. the higher the speed the worse the vibration. *ak | |||
11/06/1998 | 5 | ||
Was slowing down for a stop sign. heard grinding noises. brake pedal went to floor, rearended another vehicle. neither air bag deployed upon impact. been to dealer 5 times or more for brake problem. has squealing in rotors. *ak | |||
When applying the abs brakes the pedal traveled to the floor, causing extended stopping distance which resulted in a collision. dealer cannot identify the problem. please give any further details. *ak | |||
08/01/1998 | 2 | ||
Abs brakes failed when vehicle hit a bump while brake pad was depressed. | |||
20 | 12/15/1997 | ||
Abs fails when hitting a bump and applying brakes. loss of brakes until you reapply the brakes. | |||
4 | 07/18/1998 | ||
Abs, driver applied brake, hit a bump in the road and the brakes seem to disappear. the pedal made a trrrriccckk and clicking sound. driver released the brake pedal and reapplied brakes to stop. | |||
09/08/1998 | 1 | ||
When consumer is driving and steps on brakes, the ant-lock brakes just lock up. *ak | |||
Abs brakes; when applying brakes in a panic stop, the pedal goes to the floor and brakes fails to stop the vehicle. please provide details. *ak | |||
08/01/1998 | |||
Pulling into parking lot at approximately 10 mph, brake failure occurred ,felt pedal go to floor, two jerking motions, causing consumer to hit a pole, resulting in complete loss of brakes . *ak | |||
01/20/1998 | |||
The abs lights comes on, there is a loud squealling noise that comes from the front and rear brakes. driving on regular road surface the brake pedal moves and vibrates when hitting a bump on the road. dealer cannot duplicate the problem. *ak | |||
07/08/1998 | |||
When brakes were applied in a panic stop, the pedal went to the floor , causing the car to skid, resulting in a extended stopping distance. dealer has inspected and repaired vehicle.*ak | |||
04/01/1998 | 2 | 03/12/1998 | |
Abs failed twice. | |||
06/05/1998 | |||
When driving the vehicle at any speed between 20-60mph, on normal road conditions and when slowing down or hitting a series of bumps, the brake pedal goes to the floor. can feel the brakes disengage. the technician states that it is the design of the vehicle, and cannot duplicate the problem. *ak | |||
03/03/1998 | |||
Abs brake problems; when applying the brakes on regular road surfaces, under normal braking, if hitting a bump or irregulaties in the road, the pedal travels to the floor and there is no braking ability whatsoever. this condition has almost caused a crash. the dealer is not able to correct the prolbem. *ak | |||
12/30/1997 | |||
When the brakes are applied, the pedal goes to the floor, resulting in extended nstopping distance. the dealer has been notified. *ak | |||
SERVICE BRAKES, HYDRAULIC - ANTILOCK - ABS WARNING LIGHT | |||
12/15/1999 | 10 | 06/15/1998 | |
Very dissatisfied with vehicle. itâ¿¿s has many problems from start. while driving the vehicle and going into gears the vehicle surges forward. car shimmy's with no available fix. vehicle has strong suspension vibration and become more pronounced as speed increases. the abs light illuminated and stayed on. the brake pedal never seems to go to the floor, it just gets sponging and you feel the abs pulsating thru the pedal and the vehicle doesnt slow down, causing extended stopping distance. fuel sending unit is operating erratically. gas gauge reads empty nearly all the time regardless of level of fuel. after filling tank gauge will rise to 1/2 then as you drive a few miles it will drop and read empty. passenger side air bag assembly mounts have come loose which causes air bag assembly to move around behind dash. this rattle is very bothersome. paid a lot of money for the dealership to fix problem, but the rattle was back soon after. the bolts came loose on passenger's side front door. wheel studs on 1998 isuzu rodeo strip off. glove box in 1998 isuzu rodeo sticks and hard to open. | |||
10/24/2003 | 1 | ||
Abs, coil integrated module replacement.*mr (nar) *cb | |||
04/16/2003 | 1 | ||
The anti-lock brake light illuminated on the dashboard. *jb | |||
08/01/2001 | 1 | 03/01/1998 | |
Sway bar broke off while consumer was driving. contacted dealer, and dealer was not willing to do anything. *ak consumer states vehicle is jerking backwards while driving. dealer could not find anything, however problem persist. abs light comes on intermittently. dealer could not find a problem. *tt | |||
SERVICE BRAKES, HYDRAULIC - ANTILOCK - CONTROL UNIT/MODULE | |||
04/10/2005 | 4 | 10/10/2004 | |
You may encounter extended stopping distance abs, coil integrated module replacement its been a month and they still have not corrected the problem. *jb | |||
05/13/2003 | 63000 | 2 | 12/01/2003 |
When the brakes were applied vehicle continued to roll. driver had to hit the side of the curb to stop. mechanic replaced the anti lock brake sensor. also, in june of 2003 engine was replaced because the timing belt came off and destroyed the engine. *ak *nm | |||
04/09/2003 | 83383 | 5 | 04/24/1998 |
Consumer received a safety improvement campaign letter from the manufacturer for the abs coil integrated module replacement 021-002 notice. repair was done at 83,383 miles, and the parts were under warranty for twelve months or 12,000 miles. currently, vehicle at 100,000 miles experienced the same abs problems. *ak | |||
01/24/2004 | 65000 | 2 | |
Recall 021002000 concerning abs/coil module replacement: while driving at 25 mph, consumer came upon a stop light and applied the brakes. vehicle did not stop until it was across the intersection. the consumer was still having the problems stemming from the abs brakes that were supposed to be repaired through the recall. *ak | |||
09/12/2003 | 1 | ||
Abs electronic device failed. *ak | |||
5 | 05/12/1998 | ||
When traveling and upon making a gradual stop, consumer noticed complete brake failure, resulting in extended stopping distance. consumer has contacted dealer, dealer has replaced three brake sensors. currently, the brake problem still exists, there is an intermittent noise coming from the front wheel hub, and door closure is a problem. owner is seeking repurchase of vehicle. *ak *ml | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS | |||
10/28/1998 | 06/04/1998 | ||
Applied brakes very hard, vehicle did not stop, resulting in a crash, also the transmission sometimes jerks and makes a distrubing noise when changing during acceleration, car also jers when put in reverse. | |||
5 | 03/10/1998 | ||
On at least 5 occasions consumer experienced brake failure. when applying the brakes at low speeds(5-15 mph)a sensation was felted similar to ther eaction of the anti-lock brake pulse but very little braking power resulting in substantial brake travel. dealer said this was caused by an inadequate after market brake jon. | |||
06/01/2000 | |||
While driving braking system malfunctioned, causing extended stopping distance, which may result in a crash. dealer needs to replace all the brake drums/lines including the rear braking system. please provide further information. *ak | |||
04/01/1998 | |||
Brakes failed. yh | |||
02/28/1999 | 1 | 09/01/1998 | |
Brakes failed while approaching an intersection causing the vehicle to enter the intersection and hit another car. | |||
03/07/1999 | 1 | 02/01/1999 | |
Turned left at a low rate of speed into an angled parking space in a parking lot; as the vehicle came to a near stop the brake pedal went all the way to the floor and the car lurched forward, striking another parked car. i clearly remember the brake pedal being depressed completely to the floor at impact. i put the car in park and then in reverse to back up - the brakes seemed to work at that point. | |||
02/06/1999 | 3 | 12/01/1997 | |
On 2/5/99 i was traveling on interstate 85 in richmond when i tried to move my steering wheel , and the wheel would not move. we were heading toward a railing and i tried to use the brake to stop the car, and the brake pedal was on the floor and the car still would not stop. my son and i were almost killed because of the steering wheel locking and the brakes not working at all! | |||
11/08/1998 | 1 | 10/01/1998 | |
Brakes failed resulting in vehicle collision. | |||
08/13/1998 | 1 | 01/02/1998 | |
Front disc brakes failed. | |||
01/19/1999 | 2 | 03/01/1998 | |
At low speed 10-25mph, brake came with strong vibration but it cannot stop the vehicle | |||
08/01/1998 | 4 | 07/01/1998 | |
Air in brake system causing them to fail. | |||
08/01/1998 | 1 | 07/02/1998 | |
Brakes failed resulting in vehicle crash. | |||
09/23/1998 | 1 | ||
After applying the brakes the vehicle will jerk and stop within a couple of feet of distance. dealer was contacted. *ak | |||
04/19/1998 | |||
Any time when applying the brakes, there is a loud squealing noise coming from the rear brakes and a vibration in the steering wheel. vehicle has been taken to dealership on 3 different occasions for this problem. dealer stated that isuzu knows about the problem, but there is no solution at this time. *ak | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC | |||
3 | |||
Whenever brakes are applied vehicle fails to stop properly. had taken vehicle to dealership and was informed that no problem existed with brakes in 1999. after moving to another state experienced the same problem. took to another dealership, and informed consumer brakes were not grabbing like they should. mechanic replaced pads and rotors in the rear of vehicle. problem of non stopping still exists.*ak | |||
Brake pads and rotors are wearing excessively, front and rear rotors have rusted prematurely. also, states when brakes are applied it is extremely difficult to stop, driver has to downshift to stop the vehicle. please give any further details.*ak | |||
06/28/2000 | 11/01/1998 | ||
Vehicle had a routine service about 3 months ago which cost about $400. when driving, for the past week or two, the brakes seemed to be making a pumping noise when depressed. the service center reported that both front and rear brake pads and rotors were completely worn and warped. i'm not sure how they could have missed this in the last service visit. *ak | |||
02/01/2000 | 6 | 04/01/1998 | |
Abs system prevents stopping vehicle after hitting any bump when applying brakes at about 40 mph. dealer says that everything is working properly. problem still exists. *ml | |||
05/27/1999 | 4 | 05/01/1999 | |
All of the rotors on this car are pitted all the way around... they are all warped and this is not roght to have the entire braking system have to be replaced after 25k. | |||
10/26/1998 | |||
Ea99008; brake pads make a grinding/squeaky noise, and vehicle experienced extended stopping distanc,e which may result in a crash. dealer inspected vehicle 5 times and replaced the pads once. dealer cannot determine the problem. also, while driving at 60-70 mph, vehicle vibrated hard and pulled to the right, which may have resulted in occupant losing of vehicle control and having a crash. please provide further information. *ak | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - CALIPER | |||
08/18/2000 | 1 | ||
Brake caliper locked up while driving, the caliper was replaced and one week later the other one failed, consumer request reimbursement because he feels this was a premature failure. nlm. nlm | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - PADS | |||
06/05/1998 | 1 | 01/02/1998 | |
Brake shoes cracking, rotor and drums failed causing noise. | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - ROTOR | |||
11/03/2003 | 65000 | 1 | 09/01/2002 |
While driving 30 mph, the driver applied the brakes, because the motorist in front of her slammed on the brakes and when the consumer attempted to apply the brakes, the brake pedal went down to the floor which caused a collision. the consumer had the vehicle towed to the dealer and the mechanic noticed that the rotors and other brake parts needed replacement.*ak *cb *jb | |||
1 | 10/08/1998 | ||
The vehicle developed a pulsing in the brakes due to warpage in the rear disc brakes. | |||
06/05/1998 | 1 | 01/02/1998 | |
Brake shoes cracking, rotor and drums failed causing noise. | |||
01/21/1998 | 1 | 01/02/1998 | |
Brake rotors failed causing noise. | |||
11/06/1998 | 5 | ||
Was slowing down for a stop sign. heard grinding noises. brake pedal went to floor, rearended another vehicle. neither air bag deployed upon impact. been to dealer 5 times or more for brake problem. has squealing in rotors. *ak | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM | |||
10/31/1998 | 1 | 10/01/1998 | |
Vehicle has many problems from start, car shimmy's with no available fix, rear brakes make noise, bumper paint is very cheap, steering wheel makes rubbing noise when turned, rear cup-holder doesn't stay shut. takes too long to start vehicle. | |||
08/19/1998 | 1 | ||
Whenever vehicle slows down for a stop, it would stall out for no reason. after stalling out & waiting a while, vehicle can be restarted. had taken vehicle to dealer for repairs, but cause not found. *ak right rear brake leaking oil. *mjs | |||
11/24/1998 | 3 | 10/01/1998 | |
When the brakes are applied, a scrubbing noise is heard. the brakes have been replaced several times; yer, the problem still pursists. | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM - DRUM | |||
06/01/2000 | |||
While driving braking system malfunctioned, causing extended stopping distance, which may result in a crash. dealer needs to replace all the brake drums/lines including the rear braking system. please provide further information. *ak | |||
06/05/1998 | 1 | 01/02/1998 | |
Brake shoes cracking, rotor and drums failed causing noise. | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM - SHOES/LININGS | |||
10/01/1998 | |||
Rear brakes have been serviced 7 times, replacement of shoes each time. abs light will not go out, brakes have failed twice at very low speed during stopping. *ak | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM - WHEEL CYLINDERS | |||
04/16/2003 | 1 | ||
When the brakes were applied, the rear wheel cylinder leaked fluid. *jb *tt | |||
06/30/1998 | 1 | 01/02/1998 | |
Rear wheel cylinder failed. | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - HOSES, LINES/PIPING, AND FITTINGS | |||
06/01/2000 | |||
While driving braking system malfunctioned, causing extended stopping distance, which may result in a crash. dealer needs to replace all the brake drums/lines including the rear braking system. please provide further information. *ak | |||
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - MASTER CYLINDER | |||
03/26/2006 | 8 | ||
Received recall notice for 98 isuzu rodeo contacted bell isuzu was told the part was not available at the time called back several times,was pulling in driveway brakes went all the way to the floor smashed into bedroom of roommate. called isuzu they replaced part then said it had nothing to do with my brakes. said they tested my brake fluid it was contaminated, and that i needed a new master cylinder. the part replaced directly affected the abs brake system from working properly they believe its not failure from this abs module, aligortham thank you for your time. *jb | |||
07/01/2002 | |||
Master brake cylinder is failing. while driving brake pedal will go all the way to the floor. consumer has to pump brakes several times, and then pedal will return to normal.*ak | |||
02/01/2002 | |||
When stopping at a light brake pedal would give out and hit the floor. took vehicle to dealer, and they replaced abs module. currently, brakes get hard at a stop. took vehicle back to dealer, and they replaced master cylinder. please provide any further information. *ak | |||
03/11/1999 | 2 | 10/01/1998 | |
I was traveling down the road and when i hit the brakes the vehicle did not respond. i took it to meineke for an ispection and they reported a failure in the master cylinder. when i brought it to the dealer, they claimed the brake pedal should be able to touch the floor and then proceeded with no response. i tried to contact isuzu customer relations and they would not talk to me. *ak | |||
SERVICE BRAKES, HYDRAULIC - PEDALS AND LINKAGES | |||
08/14/2003 | 3000 | 4 | 09/26/1997 |
Brakes failed to engage after pulling away from a stoplight at about 10-15 mph. the cars ahead stopped but my rodeo would not even with me literally standing on the brakes. they were non-responsive although the abs grinding took place. i recently had the vehicle in for the algorithm change, but noticed no difference. i initially called isuzu owner relations on 7/8/02 about the msn carpoint recall alert under nhtsa campaign number 021002000, noptification date 6/02/02, affecting 161,927 vehicles. isuzu owner relations personell vehemently denied there was any cause for alarm or action from isuzu. dealership and isuzu personnel denied any problem with brakes despite calls to isuzu owner relations and visits to the dealership. this is the 3rd accident (several other near accidents) with this same type of problem occurring resulting in an accident...this time the insurance company totaled the rodeo. i had become so skeptical of this vehicle that i refused to use it on boy scout or family outings. over the years, i have owned 10 vehicles, managed sales accounts in 11 states requiring me to drive appx 25 rental vehicles per year and yet had a spotless driving record ...from 1966 to 1998, before purchasing the rodeo...go figure. will isuzu now admit that there is a problem with the rodeo? please investigate.*ak | |||
07/01/1998 | 2 | 06/28/1998 | |
Brakes failed twice while driving on a dirt road going down hill, at a stop light brake pedal went all the way to the floor. | |||
06/01/1998 | |||
When pressing the brake pedal if my foot is not all the way on the pedal , the accelerator can be pressed at the same time. this has happened on several occasions. the last occurence resulted in a collision. i believe the closeness of the pedals contributes greatly to this happening. i have found that when i have my foot on half of the brake pedal and depress fully, the accelerator is engaged by top of my foot. *ak |