Recalls

CampaignManufacturerManufacturing dateType# of units affectedDate Owner notified MfgRecall Initiated byManufacturers of recalled vehicles/productsReport Recieved DateRecord Creation DateRegulation Part NumberFMVSS Number
SERVICE BRAKES, HYDRAULIC - ANTILOCK
02I002000ISUZU MOTORS LIMITED I16192707/14/2003ODIISUZU MANUFACTURING SERVICES OF AMERICA06/03/200206/05/2002
Defect SummaryOn certain sport utility vehicles that are equipped with an anti-lock braking system (abs), the vehicles can experience extended stopping distances in certain types of braking events.
Consequence SummaryExtended stopping distance could result, increasing the risk of a crash.
Corrective SummaryDealers will provide a replacement computer algorithm for the abs that is based on the algorithm used in isuzu's my 2000 and 2001 vehicles, which have not had the problem. this campaign will be conducted in phases, with the my 1998 2wd vehicles covered first, since they have experienced the most problems. owner notification began march 20, 2003. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact isuzu at 1-800-643-4070.
NotesCustomers can also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236).

Bulletins

BulletinBulletin dateReplacement BulletinItem no.SummaryAdded
SERVICE BRAKES, AIR - ANTILOCK - CONTROL UNIT/MODULE
0309S001C06/01/20030309S001D10001768Abs (anti-lock brake system), coil integrated module replacement safety improvement campaign. *tt06/25/2003
SERVICE BRAKES, AIR - DISC - ROTOR
070900207/01/200710022539Rear brake rotors. *kb08/20/2007
SERVICE BRAKES, HYDRAULIC - ANTILOCK
SB0109S00109/01/2001627039Technical service information regarding the electronic hydraulic control unit (abs pump runs). *tt02/04/2002
SERVICE BRAKES, HYDRAULIC - ANTILOCK - CONTROL UNIT/MODULE
0309S001C06/03/200310002164Abs (anti-locking brake) system, coil integrated module replacement phase 3 announcement. *tt08/14/2003
0309S001C06/02/200310002163Abs (anti-locking brake) system, coil integrated module replacement safety improvement campaign 02i-002 phase 3 of a 4 phase release. *tt08/14/2003
0309S001B04/01/20030309S001A10001777Abs (anti-lock brake system), coil integrated module replacement safety improvement campaign. *tt06/25/2003
SB0004S00101/01/2000612588Some vehicles may exhibit one or more abs diagnostic trouble codes such as: rear speed sensor open or shorted; speed sensor missing; wheel speed input abnormality. *tt06/09/2000
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM - DRUM
IB0109S00106/01/2001621373Subject regarding drum brake adjustment procedure. *tt09/18/2001
SB9909S00211/01/19996088702Subject regarding 2wd rear drum brake adjustment procedure. *tt01/04/2000
SERVICE BRAKES, HYDRAULIC - PEDALS AND LINKAGES
9802L00312/01/1998603034Information on the accelerator pedal pad replacement service campaign. *yc01/26/1999

Investigations

NHTSA IDManufacturerDate openDate closeSubjectRecall campaign
SERVICE BRAKES, HYDRAULIC
EA99008ISUZU MANUFACTURING SERVICES OF AMERICA03/31/199907/31/2002BRAKING SYSTEM/ABS02I002001
 Consumers alleged that they experienced a loss of braking capability that resulted in extended stopping distance, and/or illumination of the abs warning lamp.
EA99008ISUZU MANUFACTURING SERVICES OF AMERICA03/31/199907/31/2002BRAKING SYSTEM/ABS02I002000
 Consumers alleged that they experienced a loss of braking capability that resulted in extended stopping distance, and/or illumination of the abs warning lamp.

Consumer Complaints

Fail datemilesoccurencesPurchase date
SERVICE BRAKES
01/29/2010170000
 Tl- the contact owns a 1999 isuzu rodeo. the contact stated that while trying to decelerate, the rear brakes seized and the vehicle skidded. the contact also stated that the brake warning light constantly illuminated. the contact believed that the failure may have been due to an abs failure. the vehicle was taken to a private mechanic who replaced the abs module but the failure recurred. while the vehicle was being inspected, the technician also noticed that the frame was rusted and corroded. the vehicle was repaired under recall nhtsa campaign number id 10v436000 (suspension) but the failure recurred. the manufacturer was notified. the failure mileage was 170,000. mah
01/29/2010170000
 Tl-the contact owns a 1999 isuzu rodeo. the contact stated there was an abs locking failure. this caused the brake light to illuminate constantly. while trying to stop the vehicle and depress the brake pedals the rear brakes would lock and the vehicle would skid. the vehicle was taken to a mechanic shop who replaced the abs module but the failure constantly recurred. the contact stated there was rust and corrosion on the frame of the vehicle after the mechanic inspects the frame. the contact stated he receives a recall notice on the suspension for the rust. the vehicle was taken to the dealer who only sprayed the frame for the rust problem but the rust problem did not go away. the recall nhtsa campaign number: 10v436000 : suspension. the manufacturer was not notified. the failure mileage was 170,000. mw
SERVICE BRAKES, AIR - ANTILOCK
04/28/2004395001001/28/2000
 In december 2002, i had the abs module replaced due to the unit 'being fried' according to the mechanic. one year later, the abs warning light illuminated and there is sporatic braking slippage especially braking down hill. unfortunately, the dealer indicated that there is a $100 diagnostic test that needs to be done to identify the problem before looking at anything. after diagnostic test, the dealer states there is a problem with the rear sensor (another $160 to fix). the 99 isuzu rodeo only has 40,000 miles at this point and has two problems with the abs system. the dealer did a vin search and my car was not part of the recall.
10/09/200369000112/13/1999
 We checked the brakes checked many times, we felt that the braking distances were extended compared to the other 2 cars that we own. every time the brake pads were checked they were determined to be okay. the anti-lock brakes seem to grab on bumpy or slippery surfaces and then let go at the end. this particular instance resulted in an automobile accident with injury and significant damage to 2 cars.*ak
07/08/200353200110/19/1998
 I was driviing down a freeway offramp and when i applied the brakes, they failed. i pumped the brakes and all the happened was that they made a bouncing noise but did not engage. i had to swerve to avoid the car in front of me where i then got hit and pushed into a guardrail.*ak
04/11/20035700004/11/2003
 1999 isuzu rodeo has problems stopping. takes a long time to come to a complete stop. check engine light comes on every two days out of the shop. burns one quart of oil in a weeks time.
11/30/20001511/01/2000
 Abs failure design problem. extended braking distance especially on wet or bumpy surfaces. the abs system seems to disengage any significant braking effect. this has not caused an accident yet, but when it happens intermittently, nothing appears to help the brakes engage in a normal fashion. the manufacturer does not acknowledge a design problem despite numerous other complaints by other owners and a recall on 1998 vehicles that they will not apply to my 1999 model. this is not a matter that can be resolved by the manufacturer or their dealer without outside intervention. the problem is serious and is endangering my family. the stopping distance is drastically increased with this system. i would feel much safer if the system could be permanently disengaged, so i could stop in an emergency. dt
11/01/1999
 No summary
07/01/1999505/01/1999
 I have had problems with the brakes on my isuzu rodeo about 5 times since may 1999. the problem occurs, if i am applying the brakes and the car goes over any bumpy surface (railroad crossing, bump in the road, uneven road surface, etc..). when this happens the brakes seem to release very much and it is very difficult to stop. i contacted the manufacturer about the problem and they indicated that they were aware of the problem, but that these abs brakes were designed this way, and they meet all federal standards. i know i was getting the company line, but i could feel that the person speaking with me agreed that this is a potential problem. he basically told me, that these abs brakes do release and the rate at which the car decelerates is reduced somewhat but it still falls within the federal mandates. the fact that your deceleration rate is not constant is where i see the problem. you cannot judge your braking capabilities, because if for some reason you hit a bump in the road while stopping, it may take you twice as long to stop. i do not want my kids riding in this car because i am afraid that we may get into an accident. any consideration to this problem would be appreciated.
10/22/1999210/01/1999
 As i pulled into a parking spot at an elementary school, the brakes failed, the throttle engaged, and i crashed into a wall. luckily, i was only going about 1 mph, but damage was done to the hood, pass. side fender, grill, and radiator. this was the second time this has happened.
07/06/1999112/01/1998
 While downshifting to 3rd gear to make a left hand turn on to montana ave. from loop 375 my brake pedal depressed to the floor and i had no brakes. i also heard a noise coming from under the front of the hood. when i pressed the brake pedal again the brakes engaged. this, however, did not take place until i was in the center of the intersection. the vehicle was taken to the service department where i purchased the vehicle. they reported that no problem was found.
SERVICE BRAKES, AIR - ANTILOCK - ABS WARNING LIGHT
04/28/2004395001001/28/2000
 In december 2002, i had the abs module replaced due to the unit 'being fried' according to the mechanic. one year later, the abs warning light illuminated and there is sporatic braking slippage especially braking down hill. unfortunately, the dealer indicated that there is a $100 diagnostic test that needs to be done to identify the problem before looking at anything. after diagnostic test, the dealer states there is a problem with the rear sensor (another $160 to fix). the 99 isuzu rodeo only has 40,000 miles at this point and has two problems with the abs system. the dealer did a vin search and my car was not part of the recall.
04/01/2003203/23/2003
 To start with, i have had continous problems with the brakes, which squeal loudly when coming to a stop, they moan & creek on the inside then forcefully pushes my foot off the pedal-- the headlights have been a real problem. i've had to replace these headlights 4 times now, 2 of which were done myself. i cannot go the speed limit on the freeways, barely even up to it, as the vehicle shakes & vibrates so violently, it feels like its being pulled apart in every direction, taking me with it. i can only get to about 46 mph before the shaking & vibrations start in. the steering wheel i have to grip tightly with both hands just to stay on the road, it shakes so much. the vehicle pulls to the right if i have to take my hands off the wheel even for a second. the driver side window & door panel rattles when the window is rolled down at any length, i can physically move the window. there is a continued buzzing on the driver's side speaker when the radio is on, even turning off the bass doesn't help. it's not on the passenger side. i don't feel safe driving this vehicle. the dealer charged me $1300 for an extended 'warranty' at a $100 deductible, but has refused to service the vehicle. i have never received the smog certificate, but was charged for the smog. the dealer who sold this piece of junk to me has completely wiped his hands of it as soon as it was dropped off on his lot. said he wasn't 'responsible' for anything this vehicle needed. i'm out several hundred dollars on this vehicle. i wasn't looking to get a vehicle that needed so much work done to it right from the start. it has been & continues to be a living nightmare! i have contacted several agencies, only to have them shut there door in my face, because this is a used vehicle. my hands are literally up in the air, i don't know what to do anymore-- what is my legal recourse?? *ak
05/06/2003690891
 After a recall on the abs system was rep[aired sensor light continued to stay on. dealer notified. *ak
04/04/200303/10/1999
 Rodeo has 60,000 miles, at about 40,000 gas gauge quit working. at 30,000 abs unit had to be replaced now abs light is on all the time. also, the key has to be turned over several times before starting. clicking noise is all you get otherwise. dealer says all repairs are our responsibility and very costly.
03/25/2003109/25/1999
 Abs indicator associated with wire harness. this problem was associated with 1998 models and should be reviewed for 1999 models too. abs module needing replacing at approximately 30,000 miles. also experience delay or lapse time for vehicle to stop.
SERVICE BRAKES, AIR - ANTILOCK - CONTROL UNIT/MODULE
12/13/199910000107/10/1999
 As i was attempting to merge onto a highway exit ramp, i applied the brakes with what was typical force for such conditions. the road was wet and as i was braking, the vehicle went over an expansion joint in the overpass of the road. the brake pedal went to the floor, the wheels locked up, and the vehicle skidded, using excessive braking distance, thus resulting in a low-speed rear-end accident with the vehicle in front of me. little damage was done to the other vehicle; however, the front bumper of my vehicle, a 1999 isuzu rodeo was pushed back. i now find out that isuzu has issued a safety recall for the abs, which is responsible for this accident and the resulting damage to my vehicle. the damage has never been repaired. i would like isuzu, as a part of its recall campaign to repair the damage to the front bumper, free of charge.
04/28/2004395001001/28/2000
 In december 2002, i had the abs module replaced due to the unit 'being fried' according to the mechanic. one year later, the abs warning light illuminated and there is sporatic braking slippage especially braking down hill. unfortunately, the dealer indicated that there is a $100 diagnostic test that needs to be done to identify the problem before looking at anything. after diagnostic test, the dealer states there is a problem with the rear sensor (another $160 to fix). the 99 isuzu rodeo only has 40,000 miles at this point and has two problems with the abs system. the dealer did a vin search and my car was not part of the recall.
01/04/2003106/06/1999
 I have a 99 isuzu rodeo with about 37,500 miles. about 2 weeks ago (early january 2003), i started up the rodeo and heard a very loud sound coming from under the hood, which continued even when i turned off the ignition and removed the keys. the only way to stop the sound was to unplug the abs fuse. when i took it to the dealership, they said the abs control module had to be replaced (about a $500 repair.) from my internet research, this is a frequent problem with mid- to late-90s rodeos.
SERVICE BRAKES, AIR - ANTILOCK - WHEEL SPEED SENSOR
04/28/2004395001001/28/2000
 In december 2002, i had the abs module replaced due to the unit 'being fried' according to the mechanic. one year later, the abs warning light illuminated and there is sporatic braking slippage especially braking down hill. unfortunately, the dealer indicated that there is a $100 diagnostic test that needs to be done to identify the problem before looking at anything. after diagnostic test, the dealer states there is a problem with the rear sensor (another $160 to fix). the 99 isuzu rodeo only has 40,000 miles at this point and has two problems with the abs system. the dealer did a vin search and my car was not part of the recall.
SERVICE BRAKES, AIR - CONTROLS - FOOT CONTROL
04/01/2003203/23/2003
 To start with, i have had continous problems with the brakes, which squeal loudly when coming to a stop, they moan & creek on the inside then forcefully pushes my foot off the pedal-- the headlights have been a real problem. i've had to replace these headlights 4 times now, 2 of which were done myself. i cannot go the speed limit on the freeways, barely even up to it, as the vehicle shakes & vibrates so violently, it feels like its being pulled apart in every direction, taking me with it. i can only get to about 46 mph before the shaking & vibrations start in. the steering wheel i have to grip tightly with both hands just to stay on the road, it shakes so much. the vehicle pulls to the right if i have to take my hands off the wheel even for a second. the driver side window & door panel rattles when the window is rolled down at any length, i can physically move the window. there is a continued buzzing on the driver's side speaker when the radio is on, even turning off the bass doesn't help. it's not on the passenger side. i don't feel safe driving this vehicle. the dealer charged me $1300 for an extended 'warranty' at a $100 deductible, but has refused to service the vehicle. i have never received the smog certificate, but was charged for the smog. the dealer who sold this piece of junk to me has completely wiped his hands of it as soon as it was dropped off on his lot. said he wasn't 'responsible' for anything this vehicle needed. i'm out several hundred dollars on this vehicle. i wasn't looking to get a vehicle that needed so much work done to it right from the start. it has been & continues to be a living nightmare! i have contacted several agencies, only to have them shut there door in my face, because this is a used vehicle. my hands are literally up in the air, i don't know what to do anymore-- what is my legal recourse?? *ak
SERVICE BRAKES, AIR - DRUM - SHOES/LININGS
06/01/200352401/07/2001
 This car is a lemon. there seem to be major electrical issues. the dash lights are going out, there is a problem with the power shift indicator - the car can be in drive, yet the indicator will have neutral displayed. this causes the car to jerk while shifting. the rear suspension has a vibrating sound no one has figured out......the dealer claims the suspension is fine. in addittion, the rear drum brakes continually go out.*ak
SERVICE BRAKES, AIR - SUPPLY - CHECK VALVE
 Brakes won't engage till foot is have way to the floor. cause is unknown. please provide any further information. ph
SERVICE BRAKES, HYDRAULIC
04/25/200572
 We have a 1999 isuzu rodeo my daughter was driving at about 25 mph during the rain when she gently applied the brakes, she heard a noise the rodeo began sliding causing an impact which resulted in an accident. various other times we would be driving and especially during wet road conditions the brakes made a noise causing the tires to rotate prematurely in an uncontrollable sliding motion.in 2011 we took our rodeo in on recall no. 10v-436, (excessive corrosion may result in the left or right rear suspension lower link bracket becoming detached from the frame, which can affect vehicle handling and potentially cause a crash.) the dealership performed the inspection which was determined that the recall should not be performed. due to excessive corrosion the reinforcement bracket remedy would not be appropriate. in order to perform this recall the body is detached from the frame and if corrosion is present on the frame this recall would only cause further damages weakening the frame making it unsafe to operate the vehicle. the frames should be recalled also! the frames also have excessive corrosion and also once a frame is compromised it's weakened! by doing this recall it dimishes the integrity of the frame anyway. therefore, this recall is not a resolution to the problems it's a bigger safety issue and puts many consumers at risk! as for isuzu providing the consumers with an appropriate remedy... this is not happening!
04/27/200540000
 Tl*the contact owns a 1999 isuzu rodeo. while braking and attempting to stop the vehicle, acceleration occurs and the vehicle makes a grinding noise at the same time. the failure has been occurring for months. a new abs was installed, but the grinding noise persists. the contact called the isuzu manufacturer and was advised to take the vehicle to the dealer for a diagnostic. the dealer suggested that the brake booster may have a hole in it and needed to be changed; however, this was not the case. the dealer stated that they could not remedy the failure. the failure mileage was 40,000 and current mileage was 100,000.
06/04/200660000201/07/2003
 A brake problem that occurs when stepping on the brakes over bumps. the braking distance increases and could cause an accident if following another vehicle closely. and the fuel gauge does not work. *nm
05/27/2004780001
 While driving at 15 mph and applying the brakes the pedal went all the way down resulting in extended stopping distance. as a result the vehicle was involved in a front end collision. two weeks prior to the accident the dealer replaced the rear brakes. *nm
08/15/200360000
 I recently was involved in an accident that i could not avoid. 2 weeks prior to the accident i received a recall in the mail for my abs module and brake system. although my abs light was already on i assumed the recall was why. i took it in, they supposedly fixed it. i guess i was wrong. i drove up and told the gentleman that my abs light was still on, and i asked why he said that that wasn't part of the recall. my question is how can it not be part of the recall when it's part of the module. so i left it and decided to take it back when i can get the money to cover my co-pay. the i get in the accident, keep in mind that they just fixed my abs system and brakes. it had rained and i tried to stop to keep from hitting someone. it didn't work, i've had vehicles with abs before, so i know what they are suppose to do, and that didn't happen. i just slid and i mean slid into this guy. if the isuzu place where i took my vehicle to get fixed would have been fixed right the first time, i could have avoided this whole situation. but instead i got this whole story about hooking it up to a diagnostic machine &there could have been 30-40 different things wrong with it, and that would cost me $180.00. but instead i took it for granted that they fixed the recall defect. that's only my first complaint, i have had numerous problems with my gas in this vehicle. i took it in 2-4 times to get it fixed and all they do is a visual inspection, and tell me nothing is wrong. there is when i use 1/4 tank of gas going 12 miles.
07/15/200218822
 I have had the same problem every year with my air conditioner. the compressor has been replaced every time, twice last year with in 3 months of each other. they have replace the following parts as well gaskets, dryer, valves and cooling clutch. now i have it in the shop again today. they could not find anything wrong at first except that i was low on freon and they said i should be adding each year. this is not right. now they tell me they found a bad o ring that goes to the hose off the dryer from the air conditioner. i have to pay $100 for the extended warranty charge. i don't think i should even have to pay this.
05/19/2003108/01/2000
 A faulty rear speed sensor caused the abs light to illuminate while driving. *nlm *scc *jb
1
 When the brakes were applied, the rear of the vehicle slid, as a result, the consumer rear ended another vehicle and none of the airbags deployed. *jb
04/01/199928
 While driving the consumer applied the brakes and the pedal went to the floor. the vehicle rolled to a stop. *nlm
1
 While driving 25 mph the consumer applied the brakes and the pedal went all the way to the floor and as a result consumer hit another vehicle. *nlm
10/28/2002
 While traveling on a side street and he apply his brakes rpm went up 7000. and his vehicle would'nt stop the vehicle was in park and the vehicle started to vibrate and shake. the dealership is aware of the problem. ts
SERVICE BRAKES, HYDRAULIC - ANTILOCK
03/23/2009138420
 Tl*the contact owns a 1999 isuzu rodeo. while entering the vehicle, the contact noticed smoke coming from the hood of the vehicle. he then noticed that the wiring for the abs underneath the hood of the vehicle caught fire. he poured water on the wires to extinguish the flames. a certified mechanic stated that a grounded hot wire inside the abs pump caused the fire. the vehicle is currently at the contact's residence and has not been repaired. the dealer stated that they were not responsible for the failure. the current and failure mileages were 138,420.
09/10/200740000300
 1999 izusu rodeo with multiple problems: ie: abs brake light won't go out. have had vehicle serviced however when coming to a stop, vehicle slides. gas gauge light won't go out...tank is full...repair price-crazy. high idle-foot on brake and vehicle lunges forward. while driving, vehicle picks up speed quickly. windshield wipers erratic-sometimes they work, sometimes they don't and sometimes they just stop right in the middle of the window. all of these are safety issues. i'm finding that some owners fell under a recall to fix these items but i don't. i don't understand that. do i have to kill or be killed first especially with the breaking issues? *jb updated 10/23/07 *tr
02/10/20041100001506/10/2003
 The antilock brake system indication light illuminated and anti-lock brakes do not function. check the message boards on the internet and you will see alot of these problems with the same make and model vehicle. also the egr valve problem where the vehicle clogs with carbon build up causing the check engine light to illuminate intermittenly and the vehicle stalls out. the problems happen to enough of the same make and model vehicles that there should be a recall. *nm
09/01/200555000208/01/1999
 1) abs indicator light illuminated 2) non-working abs system 3) taken to dealer where sw upgrade performed. dealer indicated that service was fully performed based on sw upgrade. dealer stated there was an additional failure due to cable chafing and that cable assembly would need to be replaced to restore abs operation. *nm
06/03/2006699502
 Abs instrument warning light is lit and the abs system is not working. no pulsing during braking action and i believe that the vehicle is not stopping as quickly or with the same ability to control the vehicle that i had when the abs system was working. soft pedal has been encountered twice but not at any other time. there was a dot recall that i had the isuzu dealer correct on 5-5-2003. they corrected the problem under the abs recall, campaign number 021002000 dated 2002-jun-03 with 47228 miles on the odometer. the problem seems to have returned, but braking is sporadic and intermittent. the warning light will occasionally go out but comes back on while driving. i have had the brakes inspected, all four brakes replaced, and new brake fluid installed all within the last two weeks. nothing has changed with the vehicles braking behavior or the warning light being lit. i have contacted american isuzu motors inc. by phone on 6-27-06 and was told that they do not have any responsibility for the abs problem since they did address and correct the problem on this vehicle on 5-5-2003. i think that the abs problem is still an isuzu ongoing problem especially after reading about this problem from other owners in various internet chat rooms as well as my own experience while driving the vehicle. *jb
01/11/200460000908/12/2003
 On dry sandy road, or slightly sloped road vehicle's abs system turns on executing rapid pulses fast enough to not be effective causing extremely bad stopping distance. car slows down very slowly. to correct the failure operator eliminated the abs fuse to disable abs. brakes work fine now. *nm
04/23/2006107000112/01/2004
 Dt*: the contact stated while stopped at a stop light, with the brake pedal depressed. the vehicle suddenly lunged forward and struck the vehicle in front. prior to the accident the cruise control was being used, but was disengaged by taping the brake. the vehicle stopped only after the gear shift was placed in neutral. all occupants were wearing seatbelts and there were no injuries. the police took a report at the scene. the manufacturer has been alerted, but the vehicle has not been inspected.
03/23/2006127070101/01/2001
 Dt*: the contact stated a recall letter was received november 2005. the dealership was alerted and explained the parts were not available. the contact attempted multiple times to set up an appointment with the dealership without success. the vehicle was previously taken to the dealership before the recall letter was received and the oxygen sensor was replaced however this did not correct the problem with the abs intermittently engaging. on march 23, 2006 an accident occurred as a result of the antilock brakes. while driving around a curve on slick road conditions the abs engaged causing the vehicle to hydroplane and hit a guardrail. no injuries were sustained as a result of the accident. the police were notified. the vehicle was driven away from the accident. the manufacturer was alerted however, refused to communicate with the contact and explained the insurance company needed to call them back.
02/24/2006149000108/01/2001
 Dt*: the contact stated the brake indicator light illuminated. there is a nhtsa campaign # 02i002000 regarding the abs. after having the vehicle repaired under recall the abs light illuminated. the dealership refused to inspect the vehicle to determine the cause of the illumination unless a fee was paid. no repairs have been made. updated 04/06/06. *jb
10/14/200510010011/01/1999
 Dt*: the contact stated there is a nhtsa recall, #02i002000 on the vehicle regarding the antilock brakes. the parts needed to repair their vehicle are not available at their local dealership. the manufacturer confirmed the parts are not available. *nm
10/12/200556000101/15/2005
 Dt: the contact stated while driving on bumpy roads at various speeds the brakes did not hold. there was nhtsa recall, campaign 02i002000 regarding antilock. brakes. the parts needed to repair the vehicle was not available at th local dealership. the manufacturer confirmed the parts were not available.*ak
11/15/200540000107/21/1999
 Dt: the contact stated there was a problem with the abs. while driving at 25 mph on slippery roads abs failed, causing extended stopping distance. nhtsa recall campaign 02i002000 regarding the abs was issued. the parts needed to repair the vehicle were not available at the local dealership. the manufacturer confirmed the parts were not available. the vehicle was not inspected. *ak updated 02/07/06. *jb
12/16/2005101000305/28/2005
 I have a 1999 isuzu rodeo. i try to stop, put brake pedal to floor and truck keeps accelerating and doesn't stop. i almost got in two accidents today. *jb
06/15/200468000204/29/2000
 Dt: the contact received a recall nhtsa recall campaign 02i002000 concerning the anti-lock brakes in june 2004. she contacted the dealership to make an appointment. the dealership told her the remedy parts would not arrive until december 2004. the parts never arrived. last month she received a second recall notification concerning the anti-lock brakes. someone from the dealership contacted and informed her the recall parts were available, and to schedule an appointment. on the day of the appointment she dropped vehicle off and returned home. then, she received a call from the dealership telling her the parts were not available, and she needed to come and pick up the vehicle. as a result of not being able to have the recall repairs completed the abs failed. the contact depressed the brake pedal to stop and the vehicle began to skid. *ak
10/14/2005102/01/2005
 Dt: the contact states there is nhtsa recall campaign 02i002000 concerning the antilock brakes. the parts needed to repair the vehicle are not available at the local dealership. she spoke to the manufacturer who has confirmed the parts were not available. *ak update 1/4/2006 - *nm
10/14/2005108/25/2000
 Dt: the contact received a safety improvement notice on nhtsa recall campaign 02i002000 concerning the hydraulic anti-lock brakes. at this time the parts have not been available . the manufacturer has been contacted, and stated parts were available, however, the parts have not been receive. no repairs can be made until the parts arrive. *ak
10/22/200590000104/10/2005
 Dt: the contact states there is nhtsa recall campaign 021002000 concerning the anti lock brakes. the parts needed to repair the vehicle are not available at the local dealership. she spoken to the manufacturer who confirmed the parts were not available. the contact's son was in an accident due to brake failure. the other driver was injured. a police report was taken at the scene.*ak
12/05/2004
 Dt: the contact states there is nhtsa recall campaign 021v002000 concerning the anti lock brakes. the parts needed to repair the vehicle are not available at their local dealership. he spoke to the manufacturer, who confirmed that the parts were not available. *ak
05/24/2005103/17/2005
 I was involved in a rear end collision where i was at fault due to the brakes malfunctioning in my 1999 isuzu rodeo. the roads were wet and i encountered problems with the braking system, causing me to hit the van in front of me. i have since received a recall notice for this exact problem. i was forced to pay a $500 deductible when this was a known defect to the isuzu rodeo's. what can i do to recoup the out of pocket expense for this accident? *nm
10/09/2004411/01/2003
 Dt: the contact s owns a 1999 isuzu rodeo. he received a recall on 10-14-05 regarding the brakes on the vehicle. the contact has not taken the car ito dealer to have the recall repair work done. the contact's vehicle was involved in an accident one year ago. a child ran o in front of vehicle, he swerved to miss the child, hit the brak they did not work, and the vehicle hit a telephone pole. a police report was taken. he felt that the accident caused other damage to the car, such as transmission slipping. he noticed the transmission slipping about five months ago. had to do a lot of repair work to the front end of the vehicle about five months ago air bags deployed ,and he has not had them installed again.*ak
12/10/2002188452
 I had an abs service repair by a dealer done on 12-10-2002 on my 1999 isuzu rodeo vehicle and the part that was replaced was a modulator for the abs sensor. last monday, 04-18-05, there was a recall that another dealer advised me to be serviced on the same nature of problem. afterwards, i've called the isuzu manufacturer's office and told them about my problem and i've pleaded if they can reimburse me on the first service repair that was done on my abs. they turned me down. i wish to bring them to the court but i was adviced if i can ask your good office to please investigate if my claims can be validated by yours. thanks. *jb
06/02/20031
 Consumer received notice and took vehicle to have work performed on vehicle and was charged when notice stated that the repairs would be free of charge. *mr *jb
05/01/20031
 Problems with abs system/ abs module. *mr the consumer he was charged to have the recall repair work done regarding the abs. *jb
02/07/20051
 Recall 021-002 was done on the truck but the abs light continued to illuminate (isuzu rodeo). *bf while driving the fuel pump failed/sender assembly failed and caused the vehicle to shut off. *nm
11/15/20027507/28/1999
 On numerous occasions for the past 2 years, when the brake pedal is pressed, it goes all the way down to the floor and does not slow the vehicle down. brake pedal must be pumped in order to slow the vehicle. there have been several near misses of rear-ending another vehicle. to date, the brake lines have been bled, master cylinder has been replaced, rotors and drums have been replaced, and manufacturer's abs module recall has been completed. none of these services have helped. the car is currently at the car dealership for the same problem. the dealership has indicated that they do not know what is wrong with it, but is continuing to investigate. the vehicle has been parked more than it has been driven over the past year for fear of an accident waiting to happen. *jb
11/29/200384413101/22/1999
 Consumer received recall 02i002000 concerning abs brake failure. consumer had repairs done on november 29, 2003. at this present time the abs light remained on while driving, and the vehicle was experiencing extended stopping distance when braking. dealer was not notified. *ak
04/18/2004507/01/1999
 When depressing the brake pedal, the vehicle shook in the rear. this caused extended stopping distance. consumer will notify the dealer about this issue. *ak the driveshaft was replaced and the slip yoke was lubricated. the problem still occurred. *sc *jb
01/28/20021
 Nar 06/26/2003 geico insurance claim. *mr consumer experienced brake failure as a result of the wet roadway and collided into the rear of another vehicle. the vehicle sustained more than twelve thousand dollars in collision damages. *ph *cb
06/04/2004626001
 After starting the vehicle abs light illuminated on the instrument panel. recall 02i002000 was issued. dealership would not repair this vehicle because the vin was not included. *ak
05/29/2004893001
 The abs recall 02i002000 repairs failed to correct the brake problem. when the brakes were depressed they failed to stop the vehicle immediately, resulting in extended stopping distance. *ak
05/11/2004470001
 While driving on bumpy/wet surface abs brakes failed, causing extended stopping distance. dealership was notified, but did not resolve the problem. *ak
09/19/2003107/01/1999
 With a simple push of the brakes, consumer spun out twice hitting a tree the second time. *ph soon after the accident, the consumer received a campaign notice in the mail. the consumer requested a refund for the car rental and deductible, however the manufacturer stated the abs, coil integrated module replacement was a safety improvement campaign, which was an improvement to the abs , the recall did not address or infer there was a defect, since the abs in the vehicle at the time of the accident met all standards. the consumer received two letters. the first letter stated an accident could occur and the second letter stated the campaign notice was an upgrade. *jb
03/05/200408/15/2000
 The vehicle started revving up when i applied the brakes, with rpm's increasing after i had the vehicle serviced at a dealer for a recall on the abs. when i took vehicle back for problem on march 5,2003, they said could find nothing to indicate source of problem and that it may be transmission. my local news station showed problem like this on other makes of vehicle that resulted in crashes/injuries. i do not want to be a statistic on some billboard, nor do i want that to happen to others. wonder if problems on other vehicles happened after replacing abs?
02/20/200433335102/09/2004
 When approaching a stop light brake pedal was depressed and it went down to the floor without stopping the vehicle. then, consumer's vehicle hit the vehicle in front. vehicle was towed to a repair shop. insurance company found that vehicle was under recall 021002000 concerning abs brake failure before the current owner bought the vehicle. recall repairs were done, but recall repair parts failed which caused the vehicle not to stop. *ak *mr
500001
 Nhtsa recall 021002000/abs brake system. consumer made several attempts to contact the dealer, who stated that abs brake system will not be available for several months. *ak *la
01/27/20041
 The consumer received a recall letter on the anti-lock brake system three months ago. three months later, the dealership still does not have the parts to conduct the recall. please provide further information. *jb
07/01/20032
 Recall# 02i002000 concerning abs. brake failure. the vehicle was taken to the dealer for the recall repairs. after the repairs were done vehicle still having problems with the abs not operating properly.*ak
01/05/2004520003
 I am still experiencing the inability to stop my 1999 isuzu rodeo on occasion even though i have had the abs control module replaced according to the 02i002000 recall. the dealership replaced the abs cim on 10/29/2003. on 1/9/2004, i lost control of my brakes twice in winter weather. the brakes went almost to the floor with a grinding sound and to stop, i used my hand brake. i had a friend recreate the problem the same day. i don't believe the recall has solved the problem. this is a very dangerous situation, and i'm afraid to drive my car! *la
10/09/2003670001
 Dealership did not have the parts to perform abs recall 02i002000 repairs for over 60 days. also, dealer did not know when the parts will be available.*ak
11/17/200331501/01/1999
 Abs antilock breaks
12/30/2003530001
 The vehicle continued to experience problem with the abs after the vehicle was serviced for nhtsa recall #02i002000on. the dealer stated that there was nothing they could do and that they replaced the component indicated in the recall. *nm *nm
1
 Vehicle's abs module is not functioning correctly, abs warning light comes on.*mr the consumer requested reimbursement since learning of a recall on the anti-lock brake. *ts *jb
11/05/2003800001
 Vehicle was taken to the dealer on 11/5/2003 for recall 02i002000 repairs concerning abs failure. right after the repairs were done, consumer noticed the abs light illuminated. dealer told the consumer to bring the vehicle back the next day. while the consumer had the vehicle it experienced extended stopping distance. consumer took the vehicle back to the dealer, who charged the consumer a fee for doing a diagnostic test.*ak
11/05/20033
 On february 2000 driver depressed the brake pedal at 20 mph and vehicle took longer to respond to the pedal application. the road surface was wet from raining that day. as result, the vehicle was involved in a head on collision, on january 2001, while driving 50 mph. consumer applied the brakes and they did not respond, causing vehicle to collide with the guard rail. on november 5, 2003, again, on wet condition, while pulling out of the garage onto main road, the brakes took longer to respond. as result, the vehicle crashed into a neighbor's vehicle. on those three occasions, the front air bags failed to deploy. *ak
1
 Upon arrival to the dealership to have recall repairs for the abs 02i002000 performed consumer was told,they were too busy and they wouldn't be able to do it. this was after they had told the consumer to bring the vehicle in the day before, and no appointment was necessary. also, consumer was told to bring vehicle back on monday which was not am opportune time due to travel arrangement for that day. *ak
1
 The dealership doesn't have the parts to perform nhtsa recall 02i002000 abs repairs dealership doesn't know when the parts will be available. the abs warning lights illuminates while driving.*ak
06/01/2002100454
 Problems with 1999 isuzu rodeo brake equipment.*mr consumer was informed the rear pads needed to be replaced and the rotors cut. the abs light came on as a result of a short in the abs module which was replaced. consumer later received a recall for the abs module and wanted reimbursement for the previous repair. consumer was told to contact isuzu. consumer did receive a portion of his refund. *ph *jb
10/18/200376783109/01/2003
 We had a serious safety event with a 1999 isuzu rodeo. i was trying to drive the vehicle up service ramps to change the oil. to go up the ramp, i pressed the brake with my left foot while giving a little gas with the right. this is the same technique i have been using, on the same ramps for at least 15 years, with several other vehicles. (two other vehicles i routinely service also have abs braking systems). on this occasion, the vehicle shot forward. as best as i can determine, the front brakes locked up while the back wheels did not. i got the abs effect on the pedal, while the vehicle shot forward, collapsing the ramps and sliding on them 20 feet before i could get the vehicle to stop. the actions i performed are exactly the same as i would use trying to position the vehicle while going up a steep hill. i am a at a loss to understand exactly what happened except that pressing the brake harder did not work. i was not able to stop the vehicle until i took the transmission out of gear. apparently, once the front wheels stopped turning, while the rear were rolling, the abs system prevented the brakes from stopping the rear wheels. (when the transmission shifted to neutral, the forward drive stopped, but the engine did not race indicating that i was not pressing the accelerator). fortunately, there was no car coming down the street, and i was able to get it to stop before we hit the car across the street. *la
10/14/200350000412/02/2000
 The brake system on this vehicle has been worked on 4 times this year. they brakes are usually good for a couple of weeks. they brakes stop then jumps forward. just had the dealer repair the abs system 2 weeks ago now the brakes are squealing and going to the floor. just barely stops. have read over a hundred reviews about brake problems and also the gas gauge not working for the second time in 3 years. *la
1
 Problems with abs on a 1999 isuzu rodeo. *mr there were intermittent abs problems since purchase. the abs module was changed. the dealer said that a recall was being issued and they would reimburse the consumer for the repair charges. there was an excessive oil consumption problem which had not been solved since the consumer was given the run around. recall# 02i002000 *scc *jb
01/01/20031
 Problems with abs module on 1999 isuzu rodeo. *mr the part was replaced. the consumer received recall #02i002000 which seemed to be the same problem, and requested reimbursement, however no one returned the consumer's calls. (daughter on behalf of father phillip andreula) *scc *jb
192262
 Problems with vehicle's fuel injection system and abs. consumer had to pay over $500.00 in repairs for a part for the fuel injection. the consumer also had work done on the abs, because the light had came on again, the consumer just received a recall notice for abs, but the repairs had already been done. the consumer felt the dealer should reimburse her for cost of repairs. *mr *cb *jb *jb
08/06/20031
 Recall 021002000 concerning abs brakes. recall repairs not performed due to lack of parts. isuzu dealer 775-851-5000. *ak
1
 Consumer has made several attempts to make an appointment with the dealership to have recall 02 i 002 000 repairs on abs brakes performed. dealership did not have an appointment date available.*ak
08/09/20031
 Consumer states that when trying to apply anti lock brakes brakes will lock up, causing extended stopping distance. dealer notified. *ak
02/02/2003110/31/1999
 I purchased a new 1999 rodeo which currently has approx. 50,745 miles. 2nd day of owning the vehicle, check engine light stayed on, took it to the dealership which fixed the problem; driving out of the lot for the second time, light came back on, took the dealership 1 week to try and figure out what was wrong with the car. fortunately, that problem was corrected. now, the fuel gauge indicator light continuously flashes or stays on when tank is full, making it very difficult to know how much gas is really in the tank. not to mention the anxiety trying to remember when i last filled the tank and how much fuel it took.car vibrates at speeds higher than 55mph steering wheel just shakes. problem with the anti lock braking system. while driving over wet surfaces or bumps, anti lock brakes seem to slide causing vehicle to continue to move after brake has been applied. timing belt was cracked and had to be replaced without ever receiving any notification from isuzu therefore, i had to absorb the cost of replacing a defective item originally installed by the manufacturer. hoping isuzu will reimburse. i have not received any recall notices since i purchased the vehicle in 1999. *ak
08/04/2003482971
 While stopping vehicle made a loud noise and hopped forward until it hit another vehicle. driver applied pressure to the brakes, but could not stop the vehicle. front end was damaged. the dealer determined the problem was with the abs system. *ak *nlm
106/01/1999
 The dealership did not have parts to perform recall 02 i 002 000 repairs for abs. dealership did not know when the parts would be available.*ak consumer contacted the mechanic and they stated the parts were ordered but they haven't came in yet. the consumer then contacted the isuzu dealership who stated there was no backlog on parts and the mechanic was lying to the consumer. *ph *jb
1
 Consumer noticed that when applying abs brakes vehicle goes into extended stopping distance, resulting in a vehicle crash. *ak
07/24/20031
 Consumer stated that while driving and without warning the abs failed, causing the pedal to go to the floor. dealer notified. *ak
01/20/2003397231
 The vehicle experienced abs module failure. the consumer felt the vehicle part should not have failed. *mr the abs module had already been replaced prior to receiving recall notice 021002. the manufacturer informed the consumer, the recall and the failure of the abs were not related and therefore the consumer would not be reimbursed. *tt *jb
1
 While traveling abs indicator light flashed throughout travel. *ak
05/19/2003
 Vehicle was involved in an accident due to faulty brakes on 5/19/2003. abs light illuminated after the accident. vehicle is currently at the dealership for repairs. *ak
05/31/200106/05/1999
 Isuzu rodeo campaign notice 02i-002. this is a safety improvement campaign dealing with abs, coil integrated module replacement. the explanation is that when applying brakes on a bumpy road surface or when one side of the road is more slippery than the other, you may encounter extended stopping distances. this could lead to a crash. in my case, this led to a minor crash with another vehicle which resulted in minor damage to the front bumper of my isuzu rodeo vehicle. i received this campaign notice after the incident. when i contacted isuzu to request reimbursement for the damage i received i was told that they would not be held liable since this is only an safety improvement campaign and not a safety recall. this seems contradictory to what is implied and i would like to file a complaint against isuzu in their handling of this matter and to document that this is a potentially hazardous defect.
01/28/200355000
 I own an isuzu rodeo 1999 the light for the abs system came on and does not go away plus i noticed somebody also has problems with the gasoline meter it happens that it does not register exactly how much gas in it and the light sometimes stays on plus the last one i have not see is the paint is cracked in the whole body is black. *nlm
05/10/2003330001
 While driving 60 mph the vehicles abs system failed which resulted in an accident. *nlm
28
 While driving the consumer applied the brakes and brakes pedal went to the floor but the vehicle did not stop. the dealer stated it was normal abs function. *nlm
05/02/20031
 While driving the abs brake light appeared on the dash. *nlm
05/05/20026500004/16/1999
 At about 65,000 miles, the engine has been burning 1/2 quart of oil every 200-300 miles. not leaking onto the ground and do not see in the exhaust. anti-lock brake system (abs) light comes on and off when going over bumps. the abs sensor connection on the rear axle is always loose. gas gauge not reading proper level. have been through 5 in-dash cd changers. *tt
05/01/20031
 The dealer indicated that the parts for brake recall 02i- 002000 would not be available in a reasonable amount of time. *nlm
04/21/200330000605/15/2002
 Multiple occurrences of brake/abs malfunction when applying brakes, with the vehicle in motion at relatively low speeds - approx less than 20 mph. in each occurrence the brake pedal strongly resists foot pressure, braking action is minimal-to-nonexistent, and the abs unit emits a groaning/grinding sound from vicinity of the engine compartment. in these situations there is a high risk of collision with stationary vehicles ahead in traffic. as greater pressure is applied to the brake pedal in an attempt to stop the vehicle, in some instances the faulty abs action abruptly ends - causing the vehicle to jerk to a sudden stop. this behavior risks causing a collision by closely following vehicles. after each of these malfunctions, the abs light on the console appears and there are no further malfunctions during that particular trip. driver has removed the abs fuse to prevent the problem from re- occurring. *nlm
10/15/20021
 The brakes locked up, when they were applied, which caused the vehicle to experience extended stopping distance. *jb
01/01/2003103/20/2000
 I was never informed of some recalls on my 1999 isuzu rodeo. i am having some of the problems stated in the description of the recalls. my abs brake light is going on and off and i am having some trouble stopping. my check engine light is coming on and when sitting still the car acts as though it is going to cut off. it is running really hard when i come to a stop. i believe that these have to do with the recall. another problem that i am having is my gas gauge is not registering how much gas is in the car and the gas light stays on constantly. i know that it is full because the gas pump stops. *nlm
11/04/200128000304/28/1999
 I have 1999 isuzu rodeo. i got the abs keep running and got a light on problem recently and i got the abs diagnostic at dealer and they said i have abs short and need to replace abs module. i checked the recall on this vehicle and found abs recall starting 1998 model. i already have three accidents from extended stopping distances before. is it possible to get mine to get the recall service? *nlm
03/25/2003109/25/1999
 Abs indicator associated with wire harness. this problem was associated with 1998 models and should be reviewed for 1999 models too. abs module needing replacing at approximately 30,000 miles. also experience delay or lapse time for vehicle to stop.
 The vehicle experienced extended stopping distance. *nlm
03/04/200328000106/07/1999
 When i try to stop my 99 rodeo about 1 out of 5 times the brake pedal will pulsate very fast accompanied by a sound (like a quiet machine gun) coming from the engine compartment. this is the abs kicking in. dealer says i'm not covered. have contacted isuzu but only get answering machine. reading on an isuzu forum (not sponsored by isuzu), this seems to be a known and common problem with rodeo's that isuzu doesn't want to address if your out of warranty. my 99 has 29,000 miles on it but it is over 3 years. i bought it new. *jb
09/02/2002
 The brake pedal went to the floor and caused the vehicle to experience extended stopping distance. *nlm
12/01/2098
 Oem tires wear out quickly, my wife and i owned 2 of these vehicles. one with yokohamas one with goodyears. uneven tread wear resultin in tire cupping and very rough ride. her rodeo was a ls 4wd mine is a 2wd base model. i look at tires on other rodeos i come across in parking lots and all show signs of uneven wear. also abs system is junk. any stop not executed on even level pavement results in loud grinding noise and very long braking distances. this is obviously a major problem with these vehicles and i consider it very dangerous. it's almost as if the computer gets confused and resets during anything other than ideal braking conditions. please investigate this issue further! my brakes just failed the other day as i was backing up and i hit another car. dt
05/06/2001304/01/2001
 When driving on bumpy roads or in wet conditions abs brakes ingage unnecesserally causing increased vehicle stopping distance. this has happened on three occasions scarying the hell out of me. on approaching a t-junction in wet conditions, i applied the brakes in normal fashion and a loud juddering noise was heard. brake pedal went soft, vehicle lurched fwd and finally stopped in the middle of the intersection. luckily no traffic was coming otherwise a serious accident could have occurred. i have disconnected the abs since as the vehicle is uncontrollable in these situations. dt
11/12/20021003/01/2001
 The vehicle experiences extended stopping distance when braking over rough terrain, pine cones, pot holes, etc. the brakes release and recatch with the pedal almost to the floor. dt
10/31/200248802106/01/1999
 Consumer stated while driving and without warning the abs pump failed, which caused the vehicle to experience extended stopping distance. dealer notified. mr *tt *jb
05/01/200210/01/2098
 Mr
09/01/20021
 Ea 99 000/braking system-abs:consumer states that the vehicle abs motor would remain on after switching off the vehicle. consumer had to disconnect the battery cable to deactivate the abs motor. dealer contacted. nlm
09/12/2002101/01/2099
 No summary listed for above vehicle. *ak
06/13/2002102/27/1999
 Consumer states she parked the vehicle and heard a strange noise, after opening the hood, consumer found the abs module was stuck in the on position and was constanty running, the abs light did illuminate, the dealer pulled the abs fuse and stated that the abs module needed replaced. *slc
07/11/2002203/01/2099
 When car was first purchased, brakes would occasionally stick restricting car to 35 mph on highway. dealer suggested letting brakes wear in. problem continued off and on for about 3-4 months, we learned to pull the brake pedal up to release when stuck. in march of 2002 the abs light came on, took to dealer and they said it was just a shorted wire and fixed it. on 7/10/02 wife applied brakes while entering on ramp to highway, car went into a 540 deg spin, no accident occured. the next morning, abs light came on and abs unit continually made noise even when key was removed from ignition. dealer was called i told them my wifes rodeo is making a running noise like a fan with the key out of ignition dealer (sandy in svc)said instantly oh, thats the abs unit, i usually recommend pulling the abs fuse or it may drain the battery. the next day i called to talk to svc mgr (john michael), i said wifes rodeo was making a noise, like a fan running, without key in ignition john quickly interjected and the abs light was on. it seems that this is a common problem that isuzu seems to be ignoring at the cost of consumers, possibly the cost of someones safety. we will be responsible for the $250-$500 repair bill (3 months out of warranty). i did some research and it appears numerous reports have been filed on rodeos abs failures.*ak
07/10/2002102/01/2000
 Abs brakes light came on and stayed on. also, had to unplug fuse due to the fact it was drainnig the battery. brakes were inoperative.*ak
06/16/2002808/01/2099
 I have had this vehicle since august 1999. at various times for no rhyme or reason the vehicle surges and i have had to use 2 feet to try and stop this vehicle. i have taken it to the dealer where i purchased it as well as others to diagnose this problem. they even called isuzu to try and diagnose it and they couldnt do it because even though they said they fixed it it wasnt. it continues to do it. on june 16 i was coming to a stop at a red light, it surged and i hit a pick up truck in the rear. he had no damage but i did. i took it to the dealer ( maroon isuzu) and the new service manager told me that he would have to start from square one again even if though i had all the invoices of services performed on this vehicle. he had it for 3 days and told me he couldnt find the problem. i asked him if his wife or daughter was in this car what would he do? he said i would sell the car, and give the problem to someone else. i yelled at him saying that isnt solving the problem, and i wouldnt do that to a unsuspecting sole, he said well the next time it happens bring it in. the next day i took it to another dealer ( cerami, in paramus, nj). they told me they wouldnt touch the vehicle until the damage was to the fromt bumper and radiator was fixed. i have since called isuzu and they told me they would note it in their records. thats it? he said yes. i need help desperately to fix this problem. i wait to hear from you. thank you debbie ligieri. *ak
05/27/2002109/01/2099
 I had a narrow escape today, when the abs unit on my car started bellowing smoke; i was lucky that the car did not catch fire!! had to call the fire dept.,just to make sure that it was okay. am having it towed to the dealer tomorrow. am very frustated that this could happen to a 2.5 year old vehicle!! i am appalled that isuzu has not yet sent out a notice to owners regds., this problem; the abs on my isuzu overheaded and nearly set the whole vehicle on fire, endagering lives. i was not even aware of the problem. *ak
05/20/2002
 After shutting off vehicle abs pump kept running. vehicle was towed to dealership. abs pump was replaced.*ak
05/08/2002107/01/2099
 The abs module came on for no reason upon starting the vehicle and stayed on, even after the vehicle was turned off and the key removed. unplugging the power to the abs module was required to prevent it running until overheating and melting or something else bad. *ak
03/15/20021
 Consumer states that they are having problems with their antilock brakes and are unable to stop. nlm consumer adds the anti-lock brake light is on and found anti-lock brake sensor had failed. vehicle shuts off while driving. intake manifold gasket, #1 cylinder coil, pcm relay and crank sensor have been replaced. *tt
03/28/2002102/01/1999
 No summary listed for above vehicle. *ak
03/10/1999512/01/1998
 This is a poorly designed system with no safety in mind by isuzu
03/10/1999512/01/1998
 This is a poorly designed system with no safety in mind by isuzu. nlm
 Brake system has failed four times in one year. vehicle makes a scrapping noise. *ak
12/01/2000412/15/1999
 When driving, and upon making a sudden stop by depressing brake pedal, brakes responded, and then go out and will not re-engage untill all tires are on level ground and rotating together then the brakes will slowly return and pressure will return to the brake pedal. *jg *ak
12/24/2001110/19/1998
 During routine inspection, mechanic determined front/rear rotors and abs sensor harness needed to be replaced. rotors were extremely thin. no extended braking distance or vibration reported. *ak dealer replaced front brakes and anti-skid brake system harness. *tt
10/09/2001304/01/1999
 My son was driving my 1999 isuzu rodeo home from school. he was at a red light, stopped to take a right turn and car accelerated on its own went out of control. he tried to get it under control but it wouldn't stop; it just kept going, he went onto the other lane and collided with another driver head on. fortunately, nobody was hurt. this is the 3rd time the car has revved up and went on its own. the first time it happened to me i thought it was because it wasn't warmed up but it has happened 3 times. i called isuzu and they said they never heard of any complaint like this although i have spoken with other people who have these cars and they said the same think happened to them. i have reported it to the insurance company. i also called another isuzu dealer and he said he has heard of this happening, i think this really needs to be addressed.*ak
08/23/2001111/01/1999
 The accident occurred on the freeway, in heavy traffic. i slammed my brakes on, and i heard (and felt) the brakes lock-up, and then release (this felt like i was surging forward). it was when the brakes released that i hit the car in front of me.*ak
05/05/2001107/08/1999
 Consumer was traveling approximately 35-40mph on wet pavement and abs kicked in when brakes were applied, and rearended another vehicle. mechanic turned rotors. a complaint was filed with manufacturer. but, abs still kicks in on some surfaces.*ak consumer states that the problem is that when the abs kicks in it is ineffective, consumer also states that the abs keeps the wheels so far from lockup that the brakes do not slow the vehicle. *slc
03/15/2000402/01/2000
 Brakes failure occurs when braking while going over any type of bump such as any small bump in the road, speed bump, road drainage grate, etc.. at slow speeds (10-25 mph). this problem also occurs on wet roads. this has caused my vehicle to lurch forward into an intersection and narrowly miss rear-ending vehicles in front of me. when this issue occurs, the abs takes over causing loss of brakes for 1-3 seconds and the vehicle continues to lurch forward. i'm afraid that this will result in an auto accident one of these days.*ak
07/01/199920
 I am scared every time i drive my vehicle. i have 3 kids and this is the family vehicle that we bought for a dependable safe car. every time that i have to hit the brakes i wonder if the rodeo will stop. i have drove through intersections and not stoped at stop signs. i have lost brakes on the wet roads and litteraly been scared to drive my rodeo. i have shown the isuzu central manager that the rodeo does not stop at a certian stop sign and he still tells me that it is within normal limits. i don't know what to do at this point because i owe as much as the car is worth and i don't have the money to put up another down payment. *ak
11/01/1998
 Brakes fail when applied on bumpy roads. *ak
1
 When applying brakes in a driveway at 5mph brake pedal went further down than usual/ abs light came on, and vehicle would not stop. driver rearended another vehicle in driveway. dealer has vehicle currently.*ak consumer states there was a groaning noise. *slc
02/02/2001409/01/1999
 Ea-99-008:brakes fail, pedal seems to go to floor, loud grinding sound, vehicle uncontrollable: when trying to stop, especially if road is rough or bumpy, press on the brakes, and brakes do not work properly, loud grinding sound is heard, cannot control vehicle, need to release brakes and hit them again several times. entire vehicle shakes and won't stop correctly., feels like they are slipping, also, feels like it's accelerating. several almost identical reports seen here: 859438,860577,860572*,745017,718235,719763,878859,876147,863414,742184,726114,859438,715231,708428,838578. *k
11/01/20000
 Consumer was at a stop light and light turned green consumer's vehicle was eight vehicle in line of traffic. there was a sudden stop, she applied brakes, and pedal went down to the floor. she pumped brakes twice. also, hit vehicle in front of her because other vehicle wouldn't stop. dealership was aware of problem. *ak
05/24/2001307/01/1999
 Experienced complete brake failures 3 times within 1 week; abs light keeps going on and off; was driving less than 10 mph, heard a groaning noise from the engine area, could not press brake down (it seemd locked), had to pull up emergency brake to stop to prevent accidents, isuzu service told me there was nothing wrong with brake system and said they could not duplicate the problem*ak
04/22/2001303/01/2001
 My brakes have stopped working when i am braking and hit a bump. the brakes are also very soft and have to be pumped to insure that i have adequate braking power. my transmission slips after coming to a stop then starting forward again. also, the entire vehicle has a vibration problem and is dangerously difficult to control in simple avoidable manuevers at 55 mph and higher.
01/01/20002005/01/1999
 When the brakes are engaged they slip and if going over any bump of any size the braking system locks/slips and you have no control of the vehicle. i htought maybe it was how i was applying the brakes and have had several drives test drive and it does the same thing to them. also, another 1999 rodeo owner said their's does the same thing and it is scary not know if they are going to stop you or if you are going to slide into path of oncoming traffice, etc..... isuzu has a recall relating to lower back link and have had this work done.*ak
 On dry pavement while pulling into parking space consumer applied brakes and abs activated, causing extended stopping distance, and hit another vehicle. abs was acting when it should not. please provide further information. *ak
10/15/2000102/01/2000
 Intermittent brake failure; when applying brakes, no braking action. consumer can hear abs system kicking in, but no braking action either . *ak *jb
04/14/200109/01/2000
 The abs air pump continues to run even with the key off. the battery cavle must be removed for it to stop. the parts person at the dealer said this was a major problem in 1998. he thought it was a recall problem but the service dept. said it was not.*ak
11/01/20005007/01/1999
 Anti-lock brakes engage unnecessary at low speed causing near misses ( rearending, rolling into cross traffic, hitting pedestrians).*ak
03/07/1999203/01/1999
 Brakes: when coming to a stop light, stop sign or going over a bump at a relatively slow speed, there is a delay and brakes do not work. brake is pushed down to the floor. the truck barely stops in time. almost hit pedestrians twice due to brake failure! i'm afraid to drive my truck. dealer tells me there is nothing wrong. transmission: car accelerates on its own sometimes. it revs high and has occasionally lunged forward while braking almost causing an accident. at this point, i don't want this truck anymore. there have been problems since i got it and two recalls already. the main reason is because i don't want to kill myself or someone else when brakes fail again!!!!*ak
02/24/2001101/01/1999
 My daughter was driving the rodeo on a clear night with clean roads. she was slowing down to stop at a stop light and the abs kicked in. she heard a loud grinding noise which indicated the antilock brakes were on. she let up on the brake pedal and reapplied the brakes and got the same thing. she could not get stopped and ran into another car. *ak
02/25/2001210/01/1999
 Abs failed twice while driving through an intersection, brake pedal went to the floor and vehicle did not stop, consumer ended up hitting another vehicle, dealer could not determine cause, consumer states while driving over railroad tracks or bumps, the brakes give out. *slc
02/20/2001
 While trying to brake at high speeds, 70-80mph, brakes failed. *ak
 Intermittently when brakes are applied pedal is normal. however, vehicle experiences extended stopping distance. dealer has not been able to duplicate problem.*ak
05/01/2000
 Braking system seems to be noisy, and pedal seems to travel to floor which may cause extended stopping distance, and may result in a crash. consumer took vehicle to dealer several times, and dealer was not willing to assist consumer. please provide further information.*ak
11/26/2000211/01/1999
 Brakes don't work engine rev's vehicle lurches forward can't stop no matter how hard you press on brake pedal. *ak
05/18/20001010/01/1999
 When brakes were applied there were some cases where truck had a delayed stop and has caused several collisions that caused minor damage. *ak
05/18/2000910/01/1999
 On nine separate occasions my brakes have failed causing five collisions and sliding thru a cross walk at a school intersection. the brakes will pump & a slow gratuated stop. it has been in the shop 10 times..but no help.*ak
05/18/20000
 When putting on brakes consumer can feel abs kicking in. then will hear a popping noise, and brake pedal goes to floor, but vehicle won't stop. consumer has to use emergency brake to stop. *ak
04/01/1999
 Braking distance is too long. when applying brake abs will start, but it takes too long to slow down. dealer said as long as abs light does not come on, system is working . consumer test drove a 2000 model, braking distance was much shorter. *ak
10/12/20001008/01/1999
 There was a large accident on beltway, i turned the truck off, it would not start til the 4 try. this is not the 1st or 2nd time this has happen. at the dealership on the machine, it said truck was fine. i was told wait til it gets worst.*ak
09/27/200008/01/1999
 No summary listed for above vehicle. *ak
09/24/200010/01/1999
 I experienced loss of vehicle control resulting in front end collision and neck/back injuries due to failure of the abs .*ak
09/20/2000505/01/1999
 No summary listed for above vehicle. *ak
07/26/2000410/01/1999
 On 4 separate occasions i tried to stop rapidly and the abs engaged and would not let the vehicle stop. it just made a loud crunching noise and the pedal went to the floor . i ran into a ditch once, and 3 times i barely avoided hitting another vehicle from behind.*ak
410/01/1999
 Brakes failed to engage, causing automobile to go when stop was intended. this scares the hell out of the automobile occupants.*ak
12/17/1999207/01/1999
 When brakes are applied in hard stop my vehicle experiences extended stopping distance which result in crash on two occasions. *ak
01/01/199901/01/1999
 When applying the brakes while going over a bump or manhole cover, truck seemed to skid. the problem became worse when pavement was wet. this has also caused a couple of crashes. problem was reported to the dealership. but, problem has not been corrected. *ak *ml
05/04/2000306/01/1999
 The vehicle vibrates at 70 mph almost out of control, the tires have been balanced and rotated. the rear brakes make squealing noise when braking the dealer has tried to correct the problem twice before.
06/12/20000
 When vehicle goes over a bump in the road anti-lock brake system makes a noise, and the brake pedal goes all the way to the floor. brakes are not operable. *ak
05/19/2000501/01/1999
 The car either surges slightly or the brakes do not initially engage when stepped on in an emergency situation causing the stopping distance to increase unexpectedly. it is an intermittent problem. dealer cannot duplicate.*ak
05/13/20002
 When brakes were applied pedal went to the floor, causing extended stopping distance, and resulting in a collision and minor injuries. air bag did not deploy. no warning before brake failure. *ak *ml
05/15/20000
 While driving down a hill and coming to stop applied brakes, but the brakes did not work, and vehicle crashed into a tree. *ak
 When driving in windy weather condition at 60 mph consumer noticed vehicle became very difficult to control. also, upon making a graudal stop vehicle became very hard to stop. front end shook, causing extended stopping distance. consumer has contacted dealer, dealer has replaced brake pads. but problem still occurs. please provide any further details. *ak
10/01/1999
 Ea99008, during winter condition or wet conditions abs braking system malfunctioned, causing extended stopping distance. also, caused vehicle to jerk or lunge foward which may have caused a crash. dealer fixed a part on the abs system,and the lunging had stopped, but the braking system was still malfunctioning. please provide further information. *ak
11/01/1999309/01/1999
 Ea99008, while coming to a stop on wet road braking system malfunctioned, causing extended stopping distance. also, vehicle jerked forward which may have caused a crash. dealer could not determine the cause nor duplicate the problem. *ak *ml
09/09/1999
 Ea99008,braking system/abs; when going over railroads tracks, and at any uneven ground, pedal went down to the floorboard, and vehicle just continued to travel. truck was taken to the dealership. dealer was not able to duplicate the problem. *ak *ml
03/21/2000511/01/1999
 While driving stepped on brake pedal to stop or reduce speed, crashed into vehicle in front. when the abs was engaged, the vehicle was nearly impossible to stop. owner has since disengaged the abs in favor of manual control of brakes. *ak *ml
02/14/2000511/01/1998
 Related complaint of abs failure was filed earlier today. honda dealership service manager admitted that several passport owners (identical to rodeo) had requested that antilock brakes be disabled because driver did not like performance. ford motor company salesperson indicated that isuzu rodeo has 2 channel antilock brake system whereas gm and ford use 4 channel antilock. 2 channel is definitely inferior and possibly dangerous because it disables brakes on two sets of wheels during pulsing process whereas 4 channel only pulses individual wheel. isuzu dealership refused to comment and acted ignorant of details as to operation of antilock brakes. complained to isuzu's national customer support center and have had no response. have seen a tremendous number of complaints in nhtsa's files about isuzu rodeo's abs brakes. my last car was a gmc jimmy and i drove it for 13 years and 240,000 miles. gmc's antilock brakes are much better than isuzu's. isuzu's seem susceptible to engage at low speed especially on wet or bumpy surfaces. requesting a telephone interview... please!!! *ak
02/14/2000511/01/1998
 Repeated occurrences of antilock braking system taking over control of brakes while braking at low speed. problem is most pronounced when roads are wet or when traveling over bumpy surface with moderate brake pressure applied. first occurrence was two months after vehicle was purchased while driving on wet roads. vehicle approached intersection with railroad crossing. moderate braking pressure caused antilock brakes to take over just as vehicle was bumping over railroad tracks. vehicle was unable to stop. luckily, no other vehicle was at intersection at the time. vehicle ended up completely inside intersection. driver backed up to behind painted lines and was very startled as to action of braking system. problem occurred again on wet road at smooth intersection. assumed oil on roadway was cause of antilock brake engagement and driver reported inability to stop vehicle for unusually long period at low speed. third incident was while pulling trailer with 2000 lb load. while pulling up to residence, right front tire rolled into gutter with water. antilock brakes activated and vehicle slid forward approximately 10 feet. vehicle was only traveling about 5mph. last occurrance involved wet pavement and resulted in antilock brakes engaging at low vehicle speed (approximately 20 mph) while slowing for intersection. vehicle was unable to stop. driver tried to avoid accident by changing lane to right but was struck by vehicle on right and was pushed back into original lane. collision occurred at approximately 10 mph. vehicle was immediately brought to isuzu dealership for brake check. dealer reported tires inflated to 33 lbs instead of 26/28 according to rating on door. tires rated at 35 lbs max. dealer acted unaware of any reports of antilock brake problems with other customers, i.e. acted stupid especially when told that brake failure resulted in accident. can duplicate failure repeatedly. request telephone conversation. *ak
01/19/2000701/01/1999
 While pullilng into a parking space after depressing the brakes, vehicle continued to travel, causing consumer to run into store front. *ak
01/29/2000710/01/1999
 The problem occurs when braking while going over bumps it has happened to me too many times to list and on many occasions, almost caused me to rear end the car in front of me. i complained to dealer, but was told there were no recalls. but there were many complaints of the same nature. *ak
12/30/1999
 Vehicle experienced complete brakes failure while traveling on normal road conditions. vehicle ran off road onto a wood area and rolled over to its side. dealer/manufacturer were contacted. *ak
11/24/1999310/20/1999
 Ea99008; defective braking system malfunctioned, causing no braking ability and resulting in a crash. vehicle has been in to dealer several times, but brake problems persist. *ak *ml
12/05/1999412/01/1999
 The level of the brake pedal forces the accelerater down, thrusting the vehicle forward into intersections. *ak
10/22/1999
 While turning left into a parking lot at a near by school, went to apply brakes and they didi not work. consumer lost control and went into a wall. brakes went to the floor. it was not raining outside. contacted dealer, and they said that the computer did not register a prloblem. *ak
 Intermittently when the brakes are applied in a hard stop vehicle experiences extended stopping distance. dealer has been notified. *ak
09/03/1999
 Automatic transmission problem; while driving at 60 mph vehicle just slowed down for no apparent reason. the abs warning lightalso came on. vehicle is being checked for this problem by the dealership. please provide any further information.*ak
 On three occasions, in slow speed, the brakes were inoperative. in order to stop vehicle consumer had to reapply the brakes. *ak
04/12/1999104/01/1999
 New car, 7days old. driving up to a stop light. the vehicle slowed, but would not stop. crashed into car in front of me at 5 to 10 mph. when i was slowing down, i had time to look down to see if my foot was on the pedal (which it was), then with both feet tried to get the vehicle to stop with no luck. crash! neither airbag was deployed, and no one was hurt. *ak
1012/01/1998
 Everytime the brake is applied and the vehicle hits a bump, the abs disengages the brake and waits for 1-2 seconds before engages the brake again. this converts to quite a bit of lost braking distance. as drivers, we cannot keep monitoring the surface of the road when applying the brakes. during that 1-2 second window, there is always a sound similar to someone dropping a basketball to a concrete floor from about knee level. as the ball bounces back, it does not travel as high as before; therefore, the frequency of the sound becomes faster until it stops. by the time the sound stops, the brake engages again. i think there is faulty brake mechanism that causes this sound and the abs failure. i have spoken to the service manager of isuzu and he mentioned that that is the way abs works. please advise.
SERVICE BRAKES, HYDRAULIC - ANTILOCK - ABS WARNING LIGHT
01/01/2004104/02/2003
 Fuel sending unit/gas gauge light flashing empty when car is full of gas. abs light never goes out ...had recall repaired dash lights..car is in park but light on dash is in (n)..light on gear shift is dead rear winshield wiper just stopped working rubber seal around rear hatchback window dry rotted causing window to shatter and break while car was sitting in driveway. this is dangerous. car sliding through stop light when applying brakes to stop or when sitting still car will idle and cause car to move while foot is on brakes. humming/rattling sound coming from undercarriage of these complaints are posted on several complaint websites and they all pertain to my 1999 rodeo as well as thousands of others. my rodeo was purchased in 2003 and i was not aware of any recalls except for the abs one and i learned about that from a relative who has the same vehicle. if something breaks down or stops working on hers i can expect it to occur with mine or visa versa. something needs to be done..i will never recommend anyone to purchase an isizu rodeo if my life depended on it. everytime i take it to a mechanic there is a rodeo in the garage waiting to be worked on. the mechanic shakes his head.. *tr
12/18/2004660005002/03/2004
 Tl*the contact owns a 1999 isuzu rodeo. the contact stated that the abs light frequently illuminates and the vehicle has a delay in stopping distance. the dealer was notified. the sensors have been changed, but the vehicle continues to experience the delay in stopping distance. the vehicle is a part of recall # 02i00200 (service brakes, hydraulic:antilock). isuzu stated that the recall repair was previously performed on the vehicle. however, the contact stated that she owned the vehicle at the time and did not take it anywhere to have the recall work done. the engine size was unknown. the current mileage is 92,000 and failure mileage was 66,000.
03/01/20031
 Problems with the abs system on the 1999 isuzu rodeo.*mr dealer notified. *cb
01/01/19011
 Problems with abs system on 1999 isuzu rodeo.*mr *cb
103/12/1999
 Vehicle was taken to the dealer for recall repairs concerning abs light staying on. consumer stated the problem was not resolved, abs light continued to stay on. *ak
04/10/200336000106/01/1999
 The abs light illuminated, dealer replaced the module, however the light remained on. *jb
SERVICE BRAKES, HYDRAULIC - ANTILOCK - CONTROL UNIT/MODULE
06/15/20081295001
 I have a '99 isuzu rodeo and two years ago a recall was sent out for the abs control module. we got that recall performed, though there was nothing wrong with the control module. now it's been two years and the abs control module is bad and causing the brakes to perform unsafe. i called isuzu and their response is that it's not their responsibility to replace the replacement part. i feel that their actions dictate that they put in a part that did not meet up to spec, since the original part that was replaced lasted 6-7 years and was still good. now i'm force to spend a lot of money for repairs that should not have happen in the first place not to mention the knowledge that the replacement part only comes from isuzu and knowing now what i know, it'll only last a year or so and fail again. i just hope nothing bad happens due to it. *tr
08/30/200340897101/17/1999
 Had to replace abs module last year due to safety issues. item was recalled this year campaign no 021-002. contacted american isuzu motors to reimburse---they refused. *la
1
 Problems with abs module on 1999 isuzu rodeo.*mr consumer had the abs module replaced in the vehicle two months before receiving a recall on the exact part that was replaced. consumer wanted reimbursement for the first repair at a totoal of $303.93. mechanic replaced the abs module and assembly due to constant running. *ph
06/17/200352000106/17/2003
 Isuzu 1999 rodeo. i purchased the vehicle on 6-17-03 and on the way home the abs light went on. when i went to shut off the car the module kept running. we had to pop the abs fuse for it to stop. so the car went back the next day. from there it went to an isuzu dealer to fix. there is definitely a problem isuzu needs to deal with.*jb
04/03/2003112/23/1999
 Thursday, april 3, 2003 my 1999 isuzu rodeo began making unusual sounds from inside the hood and the abs light lit up on the dashboard. upon looking under the hood, i discovered the brake module was running despite turning the car off and removing the key. the only way to stop the module from running was to remove the negative cable from the battery. i immediately called the crest isuzu dealership in plano, texas and spoke the service department about the problem. the technician's first response was that i may qualify for a free replacement because there was a manufacturer's installation problem on some of the rodeos coming from certain plants. i gave him my vin number and he came back and told me my vin number was not on the list. i found it odd that isuzu would recognize that some parts were defective, but not respond to mine. my next step was to contact the owner relations department of american isuzu motors, inc. i initially spoke with don who informed me that in july, isuzu was launching a campaign to replace all brake modules in 1999 isuzu rodeos. i was told this was a safety upgrade and did not mean that the part had any problems. i was told that i would have to pay for the replacement of my module because it was not yet july. i am being told two separate stories from isuzu employees. i need a written response from isuzu explaining how my defective brake module is not related to the campaign to replace all brake modules in july. i don't think isuzu wants to be responsible for any accidents that may result in the next 3 months because my defective brake module was not attended to. *nlm
08/10/200240000104/13/1999
 In august of 2002 , i was driving my 1999 rodeo that i had leased new in 2002 and this running noise continued after i turned off the engine. it was the abs module. it had to be unplugged to keep the battery from being run down. the repair is about $500.00 and isuzu wants to ignore that there is a problem with this component. before the noise started,the stopping distance was very long and there was a popping feeling in the brake pedal. i took it in to the dealer and was told nothing was wrong and that was the way anti-lock brakes felt the abs light came on. all of this started with 40,000 miles on the vehicle. there is a problem with the rodeo that needs to be addressed and recalled by isuzu without the cost of life or money to the consumer. *jb
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS
02/17/2002
 While pulling into carport consumer pressed brakes and pedal went to the floor, and driver hit a house. please provide any further information.*ak
07/27/2001107/01/1999
 This request is being submitted following a fatal accident that occurred this past summer involving a 1999 rodeo. the circumstances surrounding the accident are suspicious as the driver appeared to be unable to stop his car and traveled across an entire median of an interstate, hit another car head-on and burst into flames upon impact. the driver of the rodeo was my daughter's father and his cause of death was due to thermal burns. he was trapped in the car and burned to death. questions: could brake failure have caused this accident? are there reports of explosions/fires with the isuzu rodeo? crash tests? the driver did not sustain life threatening injuries from the impact of the crash. he died because the vehicle exploded into flames and he was trapped in the vehicle. have there been another reports filed with your organization with these circumstances? please help. *ak
10/26/2000202/03/1999
 When there is ice or snow covered on the road, vehicle does not stop properly. brakes keep resetting, and vehicle takes a long time to come to a stop. consumer has contacted dealer, and dealer stated that this was normal.*ak consumer states this occurs on bumpy roads too and vehicle skids through intersections upon normal braking, dealer has bleed the brakes. at times the brake light and alternator light will illuminate, dealer found that the alternator was not charging, dealer replaced alternator assembly. *slc
8
 Anti-lock brakes engaged and vehicle hits a bump, slushy snow or ice patch caused total loss of braking system for approximately 1-3 second. this also happens in dry weather.
 While driving over bumps in road or when going up a hill, and when slight pressure is applied to brakes, pedal goes to floor, causing extended stopping distance, and resulting in a collision. dealer adjusted rear brake cable which temporarily fixed problem for 8,000 miles .please give any further details. *ak
10/01/19990
 While traveling at less than 10 mph, pressed brake pedal to stop, and brake pedal went to floor. dealer can't duplicate a problem that happens intermittently. *ak
12/24/1999106/18/1999
 A brake failure resulted in accident when the driver could not stop at stop sign. yh
12/24/1999106/18/1999
 Loss of brakes caused vehicle accident. *mjs
01/30/19991
 Brakes failed, resulting in an accident.
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC
300001
 Vehicle experiences excessive pulsation when applying pressure to brake due to corrosion on the discs. all four disc were replaced by the dealer. *ak
205/17/1999
 Consumer states when brakes were applied the brake pressured declined, upon release and re-application pressure returned.*jb
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - PADS
 When driving in windy weather condition at 60 mph consumer noticed vehicle became very difficult to control. also, upon making a graudal stop vehicle became very hard to stop. front end shook, causing extended stopping distance. consumer has contacted dealer, dealer has replaced brake pads. but problem still occurs. please provide any further details. *ak
SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - ROTOR
12/24/2001110/19/1998
 During routine inspection, mechanic determined front/rear rotors and abs sensor harness needed to be replaced. rotors were extremely thin. no extended braking distance or vibration reported. *ak dealer replaced front brakes and anti-skid brake system harness. *tt
05/05/2001107/08/1999
 Consumer was traveling approximately 35-40mph on wet pavement and abs kicked in when brakes were applied, and rearended another vehicle. mechanic turned rotors. a complaint was filed with manufacturer. but, abs still kicks in on some surfaces.*ak consumer states that the problem is that when the abs kicks in it is ineffective, consumer also states that the abs keeps the wheels so far from lockup that the brakes do not slow the vehicle. *slc
SERVICE BRAKES, HYDRAULIC - PEDALS AND LINKAGES
112/01/1998
 Consumer states the brake pedal linkage is small and too close to the gas pedal, this causes drivers foot to inadvertendly press the gas pedal when applying brakes, consumer was informed that this could not be changed, because that is the design of vehicle.*ak. consumer stated the brake pedal is too small for an automatic, the brake pedal linkage was designed wrong and is bent towards the gas pedal, the linkage should have been designed straight down and the pedal welded on the right side of the linkage.*slc
SERVICE BRAKES, HYDRAULIC - POWER ASSIST - VACUUM - HOSES, LINES/PIPING, AND FITTINGS
1
 While driving and if hitting a bump in the road brakes don't work properly, sometimes vehicle may keep accelerating.*ak

Some parts © 2024 Advameg, Inc.
Based on public records. Inadvertent errors are possible.
This web site is not associated with, endorsed by, or sponsored by and has no official or unofficial affiliation with the vehicle's manufacturer.