Bulletins


BulletinBulletin dateReplacement BulletinItem no.SummaryAdded
ENGINE AND ENGINE COOLING
23201909/29/200310004652Coolant loss (pushing out the coolant recovery bottle) and/or high engine oil temperatures may be noticed. *tt12/29/2003
20020031620106/11/200310003323Engine pushing coolant and/or high oil temperature and/or high coolant temperature. *tt10/16/2003
21202603/19/200321202610001222Improved top piston ring. *scc04/24/2003
26100801/07/200426100810001221Cylinder block flushing and air compressor coolant line relocation following an air compressor failure. *scc this bulletin supersedes bulletin sb261-008 dated 3/26/03. *tt04/24/2003
55003/04/200355010001219J-tech engine brake component improvements. *scc04/24/2003
21401712/11/200321401710001224Wastegate turbochargers/description, operation, and troubleshooting. *scc *mj04/24/2003
20020022340108/22/200210000551Ceramic roller impact damage. *tt03/24/2003
21501309/27/200221501310000119Water pump pulley installation and pulley axial runout check. *tt02/12/2003
SB26100806/08/2001SB261008621723Information on cylinder block flushing and speical fitting installation following an air compressor failure. *tt10/01/2001
SB26100802/16/2001618737Subject regarding cylinder block flushing and special fitting installation following an air compressor failure. *tt04/24/2001
SB26100702/22/2000611272Information regarding the convertion from holset qe296/338 to meritor wabco air compressor on all chassis equipped with an e-tech engine. *mjs05/31/2000
SB21301802/29/2000SB213018611270Information regarding the offset camshaft keys for e-tech engines. *mjs05/31/2000
SB21202201/25/2000611244Information regarding the new-style connecting rod capscrews beginniung in september 1999 new style phased into production on all e-tech and e7 pln engines. *mjs05/31/2000
SB23201309/17/1999609163Subject regarding heavy-duty engine coolant, coolant conditioning and elimination of spin-on coolant conditioner canister. *tt12/16/1999
ENGINE AND ENGINE COOLING - COOLING SYSTEM
SB21502103/22/2002632411Information on longer capscrews and spacers for mounting the water pump to the water pump housing. *tt07/15/2002
SB21501809/14/2001626119Subject regarding integral shaft and bearing water pump replacement information. *tt12/12/2001
1382203/01/2001620274Some vehicles with model 80 rear axles only may exhibit a whine above 35 mph. *tt07/23/2001
SB21501410/31/2000618714Subject regarding plate-type oil cooler and water pump inlet tube changes. *tt04/21/2001
SB21501601/16/2001616634Subject regarding a new-style water pump having an integral shaft and bearing arrangement developed for certain engines. *tt03/07/2001
SB21501308/04/2000614516Subject regarding water pump pulley installation and pulley axial runout check. *tt10/25/2000
SB23201310/01/1999SB232013611211Information on the heavy-duty diesel engine coolant, coolant conditioning and elimination of spin-on coolant conditioner canister. *mjs05/31/2000
ENGINE AND ENGINE COOLING - COOLING SYSTEM - FAN
SB21501510/31/2000618713Subject regarding horton fan drive installation. *tt04/21/2001
ENGINE AND ENGINE COOLING - COOLING SYSTEM - HOSE
SB21501905/24/2002SB215019634197Subject regarding redirected thermostat bypass arrangement for plate-type oil cooler - e-tech engines. nlm09/28/2002
SB21003012/28/1999611261Information regarding the engine coolant and fuel lines with crimp-on sytle end fittings. *mjs05/31/2000
ENGINE AND ENGINE COOLING - COOLING SYSTEM - RADIATOR ASSEMBLY
SB21501903/19/2002SB215019632406Subject regarding redirected thermostat bypass arrangement for plate-type oil cooler. *tt07/15/2002
SB21501911/06/2001626292Subject regarding a new thermostat bypass arrangement for plate-type oil cooler. *tt12/13/2001
ENGINE AND ENGINE COOLING - ENGINE
21303604/15/200310002215Cylinder head cover / j-tech engine brake spacer gasket and isolator improvements. *tt08/15/2003
55203/04/200355210001218J-tech engine brake component improvements. *tt04/22/2003
55210/29/200210000218J-tech engine brake component improvements. *tt02/19/2003
55010/08/200255010000217J-tech engine brake component improvements. *tt02/19/2003
21900809/10/200221900810000120Higher volume oil pump. *tt02/12/2003
21202709/10/200210000118Auxiliary shaft nut installation. *tt02/12/2003
SB21301805/28/2002SB213018634205Subject regarding offset camshaft keys for e-tech engines. nlm09/28/2002
SB22102811/20/2001SB221028626198Subject regarding fuel supply pump improvements. *tt12/13/2001
SB21302909/07/2001626076Subject regarding engine cylinder head cover changes. *tt12/12/2001
SB21302709/11/2001SB213027626103Subject regarding valve yoke guide pin breakage for chassis equipped with j-tech engine brake. *tt12/12/2001
SB21101606/26/2001621729Information on increased width of oil pan gasket at front and rear. *tt10/01/2001
SB22102007/10/2001SB221020620773Subject regarding installation of electronic unit pump (eup) plunger spring and spring seat. *tt08/29/2001
SB21401606/29/2001620769Information on the new steel-core inlet / water manifold gasket released and available through the mack parts system for e-tech engines. *tt08/29/2001
SL21300503/09/2001620033Subject regarding the termination of camshaft / lifter kits. *tt07/09/2001
SB21302703/20/2001620023Subject regarding valve yoke guide pin breakage - e-tech equipped withj-tech engine brake. *tt07/09/2001
SL26600303/23/2001620034Subject regarding correct action for engine brake drop-out complaints. *tt07/09/2001
SB21900802/20/2001618733Information on the high volume oil pump. *tt04/24/2001
SB21202401/12/2001616636Subject regarding main bearing running clearance change. *tt03/07/2001
SB21302611/17/2000616199Subject regarding camshaft and lifter break-in procedure. *tt02/14/2001
SB22102607/18/2000614524Information pertaining to the elmination of the center o-ring on electronic unit pumps. *tt10/25/2000
SB21100810/12/1999SB211008611223Information on isolating oil pan gasket vibration. *mjs05/31/2000
SB21302401/11/2000611252Information regarding cam bushings and camshaft enhancements. *mjs05/31/2000
SB21100709/03/1999609164Bulletin outlining procedures on cylinder sleeve seat repair and elimination of the cylinder sleeve crevice seal. *tt12/17/1999
SB21302105/21/1999606677Service bulletin information regarding cylinder head pipe plugs with encapsulated epoxy sealant. *tt08/31/1999
SB22102006/04/1999606636Subject on the installation of electronic unit pump (eup) plunger spring and spring seat. *tt08/30/1999
SB21401105/13/1999606620Information regarding the new e-tech breather filter housing. *tt08/30/1999
21001505/21/1999210015605927Cylinder head and cylinder block leak test procedure. *tt08/02/1999
SB21302105/21/1999605885Information on cylinder head pipe plugs with encapsulated epoxy sealant. *tt07/30/1999
SB21302205/25/1999605881Subject regarding j-tech exhaust rocker arm adjusting screw jam nut (spherical nut) tightening instructions. *tt07/30/1999
PI51509/21/1998603296Subject regarding oil pump upgrade. *yc02/17/1999
PI51609/21/1998603299Subject on valve lifter upgrade. *yc02/17/1999
SB21101311/25/1998602611Information regarding die-cast aluminum flywheel housings are replacing the permanent mold cast aluminum housings use on e-tech and e7 models. *yc01/05/1999
98051239J01705/12/1998601389The engine oil pressure and boost air temperature sensors with npt threads. *yc08/03/1998
98022331D00302/23/1998601164Service information regarding offset camshaft keys for e-tech engines. *yc07/06/1998
ENGINE AND ENGINE COOLING - ENGINE - GASOLINE
SB21101707/09/2002634213Subject regarding flywheel housing mounting pad through-hole closure plugs. nlm09/28/2002
SB21302705/24/2002SB213027634207Subject regarding valve yoke guide pin breakage - e-tech equipped with j-tech engine brake. nlm09/28/2002
SB21003405/14/2002634210Subject regarding miscellaneous fastener changes - e-tech engines. nlm09/28/2002
SB21202503/22/2002632408Information on improving twelve-bolt vibration damper. *tt07/15/2002
SB21003204/05/2002SB210032632402Subject regarding e-tech current-controlled rate shaping (ccrs) engine. *tt07/15/2002
SB22102003/19/2002SB221020632410Information pertaining to the installation of electronic unit pump (eup) plunger spring and spring seat. *tt07/15/2002
SB26601301/11/2002SB266013631939Subject regarding j-tech engine brake with top oil supply port for external oil line. *slc06/25/2002
26601301/11/2002266013631842Information on j-tech engine brake with top oil supply port for external oil line. *slc06/20/2002
SB21302704/19/2002SB213027631403Subject regarding valve yoke guide pin breakage-e-tech equipped with j-tech engine brake. *yh05/23/2002
SB21303112/21/2001627002Subject regarding initial valve lash adjustment. *slc02/04/2002
TS8570101/01/2001626344Subject regarding operation handbook natural gas engine . *aj12/13/2001
SB21303009/11/2001626106Information on flange-style jam nuts for rocker arm and valve yoke adjusting screws. *tt12/12/2001
SB21003202/20/2001618734Information on the e-tech current-controlled rate shaping (ccrs) engine. *tt04/24/2001
SB26601312/08/2000616187Information on j-tech engine brake with top oil supply port for external oil line. *tt02/14/2001
SL21001412/22/2000SL210014616201Mack trucks, inc. is notifying rebuilders of mack and renault vi manufactured engines of certain requirements that must be performed during rebuild of certain mack and renault vi engines. engines covered by the agreement are certain mack02/14/2001
SB21302310/22/1999611215Information regarding the engine valve lash acceptable range. *mjs05/31/2000
SB210-02912/17/1999611258Information regarding the e-tech engine left-side redesign. *mjs05/31/2000
SB21100709/03/1999SB211007611209Information on the cylinder sleevew seat repair and elimination of the cylinder sleeve crevice seal. *mjs05/31/2000
20019992740110/01/1999611225Information regarding the e-tech engine rough running. *mjs05/31/2000
SL21001310/23/1998602945Brief information regarding engine misfire. *yc01/21/1999
98041750A00204/17/1998601385E9 engine service notes. *yc08/03/1998
39JO1602/27/1998601162Installation and adjustment on engine speed and engine position sensor. *yc07/06/1998
ENGINE AND ENGINE COOLING - ENGINE - GASOLINE - TURBO-CHARGER
21402010/25/200210000221Turbocharger pre-lubrication procedures. *tt02/19/2003
SB21401905/07/2002SB214019634172Subject pertaining to service replacement turbo chargers for etech ccrs and pre-ccrs models.*jb09/28/2002
SB21401904/02/2002SB214019632404Information on service replacement turbochargers. *tt07/15/2002
SB21401711/16/2001626169Subject regarding wastegate turbochargers - description, operation and troubleshooting. *tt12/13/2001
SB21401404/17/2001620308Subject regarding turbocharger model / part number changes. *tt08/01/2001
SB21401504/17/2001620307Service bulletin procedures for cleaning oil and debris from the inlet manifold, charge air cooler and intake air system following a turbocharger failure. *tt08/01/2001
ENGINE AND ENGINE COOLING - EXHAUST SYSTEM
SB21401806/18/2002SB214018634201Subject regarding high-temperature center exhaust manifold and improved turbocharger mounting nut and gasket. nlm09/28/2002
ENGINE AND ENGINE COOLING - EXHAUST SYSTEM - MANIFOLD/HEADER/MUFFLER/TAIL PIPE
SB21401811/30/2001626217Subject regarding high-temperature center exhaust manifold. *tt12/13/2001