Mazda B2000 1987

Model B2000 made in 1987 by Mazda got 9 consumer complains, 1 investigation there is 1 recall as well as 2 service bulletins. Consumer complaints with reference, among others things, to fuel system, gasoline, seat belts and structure. Technical service bulletines regarding electrical system, equipment. The car had one investigation (steering). There was one recall concerning exterior lighting . The car has one 2.6, ffs engine.

Model 1987

Engine [L]CylindersTransmissionDriveEstimate MPG (city/highway/combined)Unadjusted MPG (city/highway/combined)FuelFuel costClassRelease date
2.6, (FFS) 4Automatic 4 gearsRWDRegular1 - Category 1 Truck
2.6, (FFS) 4Manual 5 gearsRWDRegular1 - Category 1 Truck

Recalls


CampaignManufacturerManufacturing dateType# of units affectedDate Owner notified MfgRecall Initiated byManufacturers of recalled vehicles/productsReport Recieved DateRecord Creation DateRegulation Part NumberFMVSS Number
EXTERIOR LIGHTING
09E012000SABERSPORT E (Equipment)1627005/11/2009OVSCMAZDA NORTH AMERICAN OPERATIONS04/07/200904/07/2009571108
Defect SummarySabersport is recalling 16,270 combination corner and bumper lamp assemblies of various part numbers sold for use as aftermarket equipment for various passenger vehicles. these headlamps fail to conform to the requirements of federal motor vehicle safety standard no. 108, lamps, reflective devices, and associated equipment. these lamps do not contain the required amber side reflectors.
Consequence SummaryDecreased lighting visibility may result in a vehicle crash.
Corrective SummarySabersport will notify owners and offer a full refund for the noncompliant combination lamps. the safety recall began on may 11, 2009. owners may contact sabersport at 1-909-598-7589.
NotesThis recall only pertains to aftermarket replacement equipment and has no relation to any original equipment installed on vehicles produced by the vehicle manufacturer.in order to determine if your aftermarket lamp assembly is affected by this noncompliance, please review the list of model numbers provided to us by sabersport.the list can be found under document search located at the bottom of your screen.owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov .

Bulletins


BulletinBulletin dateReplacement BulletinItem no.SummaryAdded
ELECTRICAL SYSTEM - BATTERY
001/97G04/08/199752503Maintenance free battery - diagnostic and charging procedure. *tw08/14/1997
EQUIPMENT - ELECTRICAL - AIR CONDITIONER
008/9705/19/199752497Use of a/c tracer dye. *tw08/14/1997

Investigations


NHTSA IDManufacturerDate openDate closeSubjectRecall campaign
STEERING
PE90091MAZDA NORTH AMERICAN OPERATIONS06/20/199010/12/1990SECTOR SHAFT FAILURE
 There is no summary currently available

Consumer Complaints


Fail datemilesoccurencesPurchase date
FUEL SYSTEM, GASOLINE - STORAGE - TANK ASSEMBLY
110/20/1987
 The design and mounting of the gas tank is such that little rocks get between the mounting and the gas tank and over time wear through the coating of the tank and create a leak. nlm
12/03/19991
 4 cyl
1
 Noticed that fuel was leaking from the seams while filling it up. could fill fuel tank half way. suddenly stopped and heard it slash, and then leaked through the seams.*ak seams seem rusted away. *yh
09/10/1998
 Fuel tank failure at welded seam.
04/17/1995
 Fuel tank leaking fuel. tt
SEAT BELTS - FRONT - RETRACTOR
209/01/1987
 Driver side & passenger side seat belt retractors failed. the driver's side is weak / the passenger side is completely broken. *yc
STRUCTURE
03/02/1995
 When driving the truck going up to high speed truck shake service station check it and say the main frame had rusted through on both side. tt
STRUCTURE - FRAME AND MEMBERS
04/29/19992
 The frame is cracked on both sides directly across from each other. location: the center of the first (forward) bed body mount,it is corroded so badly i would be afraid to weld it even using long plates on each side of the box frame. the vehicle is now unusable with the bed pushing up against the cab. i am an automotive enthusiast and business major working in engineering and studying welding and chassis engineering and am competent fabricator with tig, mig and stick processes, i have knowledge about metal and cars.