Recalls
| Campaign | Manufacturer | Manufacturing date | Type | # of units affected | Date Owner notified Mfg | Recall Initiated by | Manufacturers of recalled vehicles/products | Report Recieved Date | Record Creation Date | Regulation Part Number | FMVSS Number | |||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| VEHICLE SPEED CONTROL - CRUISE CONTROL | ||||||||||||||||
| 11V208000 | MERCEDES-BENZ USA, LLC. | from 08/01/1999 to 06/30/2002 | V (Vehicle) | 136751 | 10/20/2011 | ODI | MERCEDES-BENZ USA, LLC. | 03/31/2011 | 04/01/2011 | |||||||
| Defect Summary | Mercedes-benz is recalling certain model year 1999-2002 m-class and model year 2000-2003 m-class amg vehicles. the cruise control system in the affected vehicles allows the driver to disengage the system in a number of ways, including tapping the brake pedal, using the cruise control stalk, or braking the vehicle enough to reach a certain rate of deceleration. mercedes-benz has determined that under certain circumstances use of the brake pedal may not automatically disengage cruise control as expected by the driver, although the other means of deactivating cruise control remain fully operative. specifically, where the driver pumps the brakes rather than applying consistent pedal force, the level of force required may be unusually high. | |||||||||||||||
| Consequence Summary | Difficulty or delay in disengaging cruise control can increase the risk of a crash. | |||||||||||||||
| Corrective Summary | Dealers will repair the vehicles free of charge. the safety recall began during october 2011. owners may contact mercedes-benz at 1-800-367-6372. | |||||||||||||||
| Notes | Mercedes-benz campaign number is 2011090001.owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov . | |||||||||||||||
Investigations
| NHTSA ID | Manufacturer | Date open | Date close | Subject | Recall campaign | |
|---|---|---|---|---|---|---|
| VEHICLE SPEED CONTROL | ||||||
| PE10050 | MERCEDES-BENZ USA, LLC. | 12/21/2010 | 05/04/2011 | Brake lamp switch failure. | 11V208000 | |
| Odi opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.consumers also reported the illumination of a warning lamp on the instrument panel.the switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.as installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.one set of contacts (bls) operates the stop lamps, a second set (ewm) controls the shift interlock system, and a third set (bs) is used by an on-board diagnostic (obd) system to monitor switch operation.the cruise control monitors the bls signal to determine when the brake is applied, the primary way the system is disabled when set.the relative timing of contact actuation in response to plunger movement allows the obd system to detect a switch fault.when a fault is detected a malfunction indication lamp (mil) is illuminated (driver alert), a diagnostic trouble code (dtc) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).in its response to odi's january 2011 information request letter, mb explained its assessment of switch failures which was based primarily on evaluation of field return failures.mb identified both 1) electrical contact and 2) mechanical switch failure mechanisms.according to mb's analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.for instance mb claims that bls contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the obd system, resulting in a dtc and subsequent replacement.electrical contact failures of the bs and ewm contacts result in a dtc also, and ewm contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).accordingly mb maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.mb determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.high temperatures occur due to overheating of the bls contacts and can cause the internal plastic components to melt.in one scenario overheated bls contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.in another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.in this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.in its march 31, 2011 defect notification, mb stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11v-208) to replace the switch with a more robustly designed component.the recall includes 136,751 model year 2000 - 2002 m-class and model year 2000 - 2004 m-class amg vehicles.owner notification letters will be mailed to consumers in september 2011.this action taken by mb is sufficient to resolve the issues raised by this investigation. | ||||||
| VEHICLE SPEED CONTROL - CRUISE CONTROL | ||||||
| PE10050 | MERCEDES-BENZ USA, LLC. | 12/21/2010 | 05/04/2011 | Brake lamp switch failure. | 11V208000 | |
| Odi opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.consumers also reported the illumination of a warning lamp on the instrument panel.the switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.as installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.one set of contacts (bls) operates the stop lamps, a second set (ewm) controls the shift interlock system, and a third set (bs) is used by an on-board diagnostic (obd) system to monitor switch operation.the cruise control monitors the bls signal to determine when the brake is applied, the primary way the system is disabled when set.the relative timing of contact actuation in response to plunger movement allows the obd system to detect a switch fault.when a fault is detected a malfunction indication lamp (mil) is illuminated (driver alert), a diagnostic trouble code (dtc) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).in its response to odi's january 2011 information request letter, mb explained its assessment of switch failures which was based primarily on evaluation of field return failures.mb identified both 1) electrical contact and 2) mechanical switch failure mechanisms.according to mb's analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.for instance mb claims that bls contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the obd system, resulting in a dtc and subsequent replacement.electrical contact failures of the bs and ewm contacts result in a dtc also, and ewm contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).accordingly mb maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.mb determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.high temperatures occur due to overheating of the bls contacts and can cause the internal plastic components to melt.in one scenario overheated bls contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.in another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.in this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.in its march 31, 2011 defect notification, mb stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11v-208) to replace the switch with a more robustly designed component.the recall includes 136,751 model year 2000 - 2002 m-class and model year 2000 - 2004 m-class amg vehicles.owner notification letters will be mailed to consumers in september 2011.this action taken by mb is sufficient to resolve the issues raised by this investigation. | ||||||
Consumer Complaints
| Fail date | miles | occurences | Purchase date |
|---|---|---|---|
| VEHICLE SPEED CONTROL | |||
| 06/15/2011 | 138000 | ||
| Tl-the contact owns a 2000 mercedes benz ml320. the contact was driving approximately 55 mph with the cruise control in activation; however when pressure was applied to the brake pedal the cruise control failed to automatically disengage. suddenly the brakes locked and the vehicle continued to accelerate. the gear was shifted into neutral and then into the park position which caused the vehicle stop. the contact resumed in operation with caution. there was a recall associated with nhtsa campaign id number 11v208000 (vehicle speed control: cruise control). the recall part was unavailable to perform the remedy repair. the manufacturer was not made aware of the problem. the approximate failure mileage was 138,000. js | |||
| 03/22/2008 | 1 | ||
| While traveling with my family (wife and 2 kids) on the freeway returning from an family outing. we were traveling approximately 65 mph on the freeway when all the sudden without any warning the cars brakes are activated and the car pulls to the right, fortunately there was no car on the right lane next to me. the car braking on its own did not stop until the car came to a complete stop. after removing our hearts from our throats and changing our soiled undergarments we decided to head straight home 45 miles away. this same thing occurred about 3 times during our trip back home. i will be more than happy to allow dot inspectors to drive the car to assist your investigation. (i recommend you bring a change of underwear.). *tr | |||