Bulletins
| Bulletin | Bulletin date | Replacement Bulletin | Item no. | Summary | Added |
|---|---|---|---|---|---|
| SERVICE BRAKES, AIR - SUPPLY - HOSES, LINES/PIPING, AND FITTINGS | |||||
| RSB-2009100002 | 01/01/2010 | 10033607 | Mercedes benz: check for installation of spacer between brake and fuel line, install if necessary. the spacer between the brake line and fuel line may not have been installed. check for presence of a spacer, and if missing, install the s | 08/27/2010 | |
Investigations
| NHTSA ID | Manufacturer | Date open | Date close | Subject | Recall campaign | |
|---|---|---|---|---|---|---|
| SERVICE BRAKES, HYDRAULIC | ||||||
| PE10050 | MERCEDES-BENZ USA, LLC. | 12/21/2010 | 05/04/2011 | Brake lamp switch failure. | 11V208000 | |
| Odi opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.consumers also reported the illumination of a warning lamp on the instrument panel.the switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.as installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.one set of contacts (bls) operates the stop lamps, a second set (ewm) controls the shift interlock system, and a third set (bs) is used by an on-board diagnostic (obd) system to monitor switch operation.the cruise control monitors the bls signal to determine when the brake is applied, the primary way the system is disabled when set.the relative timing of contact actuation in response to plunger movement allows the obd system to detect a switch fault.when a fault is detected a malfunction indication lamp (mil) is illuminated (driver alert), a diagnostic trouble code (dtc) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).in its response to odi's january 2011 information request letter, mb explained its assessment of switch failures which was based primarily on evaluation of field return failures.mb identified both 1) electrical contact and 2) mechanical switch failure mechanisms.according to mb's analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.for instance mb claims that bls contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the obd system, resulting in a dtc and subsequent replacement.electrical contact failures of the bs and ewm contacts result in a dtc also, and ewm contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).accordingly mb maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.mb determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.high temperatures occur due to overheating of the bls contacts and can cause the internal plastic components to melt.in one scenario overheated bls contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.in another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.in this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.in its march 31, 2011 defect notification, mb stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11v-208) to replace the switch with a more robustly designed component.the recall includes 136,751 model year 2000 - 2002 m-class and model year 2000 - 2004 m-class amg vehicles.owner notification letters will be mailed to consumers in september 2011.this action taken by mb is sufficient to resolve the issues raised by this investigation. | ||||||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - HOSES, LINES/PIPING, AND FITTINGS | ||||||
| EA08009 | MERCEDES-BENZ USA, LLC. | 04/28/2008 | 12/16/2009 | BRAKE LINE CHAFE | ||
| Analysis of complaints to odi and mercedes and warranty claim data submitted by mercedes indicates that the alleged defect has occurred at a low rate (36.5 complaints per 100,000 vehicles and 0.29 percent warranty claim rate), with no discernable defect trend indicating that the rate of chafing related brake line failures is increasing.there have been no new complaints since january 2009.when the analysis is limited to incidents of brake line leakage that resulted in allegations of reduced brake effectiveness, the rate drops even further (22.3 complaints per 100,000 vehicles and 0.04 percent warranty claim rate). mercedes provided data showing that in the rare instances when chafing did progress to brake line leakage the driver would be immediately alerted to a problem by illumination of the bright yellow esp/bas warning lamp and changes in brake pedal feel.continued operation with a leaking brake line would result in illumination of the bright red brake warning lamp and an audible chime due to low master cylinder reservoir level. continued operation with the brake warning lamp illuminated would ultimately drain the reservoir for the affected circuit, resulting in loss of the circuit and an approximately 80% increase in stopping distances. surveys conducted by odi and vrtc indicate that routing anomalies may be more common than the complaint and warranty data suggest for the subject line bundle, with line contact or other routing anomaly noted in 13 of 51 vehicles surveyed by odi and vrtc (25.5%).while evidence of contact between the fuel line and subject brake in a particular vehicle is not necessarily predictive of eventual line failure/leakage, significant chafing wear was noted in two survey vehicles (3.9%).to address concerns with line routing and ensure that lines with evident chafing do not progress to a leak condition, mercedes will conduct an owner notification program instructing owners to bring the vehicles to a dealer for a free inspection and repair.lines that do not have a spacer (rubber grommet or omega-clip) between the subject fuel and brake lines will have an omega-clip spacer installed to ensure adequate clearance between the lines.brake lines with chafe marks will be replaced. accordingly, this investigation has been closed. the closing of this investigation does not constitute a finding by nhtsa that a safety-related defect does not exist. the agency will continue to monitor complaints and other information relating to the alleged defect in the subject vehicles and take further action in the future if warranted. for additional information regarding this engineering analysis refer to the ea08-009 closing report. | ||||||
| SERVICE BRAKES, HYDRAULIC - SWITCHES - BRAKE LIGHT | ||||||
| PE10050 | MERCEDES-BENZ USA, LLC. | 12/21/2010 | 05/04/2011 | Brake lamp switch failure. | 11V208000 | |
| Odi opened the investigation based on reports that the subject vehicle brake lamp switch (switch) failure caused 1) inoperative brake lamps (stay on or fail to illuminate), and/or 2) shift interlock failure (shifter locked in park), and/or 3) the cruise control to fail to cancel with brake application.consumers also reported the illumination of a warning lamp on the instrument panel.the switch contains three sets of electrical contacts and a (normally extended) spring loaded plunger that actuates the contacts as it moves.as installed in the vehicle, the plunger contacts the brake pedal arm and is pushed into the switch; as the driver applies the pedal the plunger extends.one set of contacts (bls) operates the stop lamps, a second set (ewm) controls the shift interlock system, and a third set (bs) is used by an on-board diagnostic (obd) system to monitor switch operation.the cruise control monitors the bls signal to determine when the brake is applied, the primary way the system is disabled when set.the relative timing of contact actuation in response to plunger movement allows the obd system to detect a switch fault.when a fault is detected a malfunction indication lamp (mil) is illuminated (driver alert), a diagnostic trouble code (dtc) is stored (for the service technician), and cruise control operation is inhibited (as a failsafe).in its response to odi's january 2011 information request letter, mb explained its assessment of switch failures which was based primarily on evaluation of field return failures.mb identified both 1) electrical contact and 2) mechanical switch failure mechanisms.according to mb's analysis, electrical contact failure is the predominate failure type and the failure consequence depends on which contact fails.for instance mb claims that bls contact failures are momentary in nature and do not affect brake light operation but are nonetheless detected by the obd system, resulting in a dtc and subsequent replacement.electrical contact failures of the bs and ewm contacts result in a dtc also, and ewm contact failures result in the shifter being stuck in the park (which can be overridden by the consumer).accordingly mb maintains that electrical contact failures of the switch have no safety consequence since the brake lamps remain operational and the cruise control is always disabled.mb determined that mechanical failures of the switch, which are rare in their assessment, can result from internal wear and/or increased switch operating temperatures.high temperatures occur due to overheating of the bls contacts and can cause the internal plastic components to melt.in one scenario overheated bls contacts may melt to the extended plunger and are damaged when the brake pedal is released resulting in the brake lights staying on.in another scenario the increased temperatures and/or internal wear can cause the plunger to stick in the fully depressed position.in this case the cruise may not cancel when the brake is applied and the driver may have to use high brake pedal forces or other means (shifting to neutral or using the cruise master switch) to disengage the cruise.additionally the vacuum assist can be depleted if the driver pumps the brakes resulting in reduced braking effectiveness and even higher pedal forces.in its march 31, 2011 defect notification, mb stated that to remediate the potential need for excessive brake force it would conduct a safety recall (11v-208) to replace the switch with a more robustly designed component.the recall includes 136,751 model year 2000 - 2002 m-class and model year 2000 - 2004 m-class amg vehicles.owner notification letters will be mailed to consumers in september 2011.this action taken by mb is sufficient to resolve the issues raised by this investigation. | ||||||
| PE10050 | MERCEDES-BENZ USA, LLC. | 12/21/2010 | Brake Lamp Switch Failure | |||
| Odi has received 15 vehicle owner questionnaire reports that allege that the brake lamp switch failed resulting in one or more of the following conditions: loss of illumination of the exterior brake lamps, an inability to shift the vehicle out of park gear position, and/or an inability to disengage the cruise control system once enabled and set.mercedes benz has previously issued technical service bulletin (tsb) 10016685, dated may 16, 2005, which discusses an improved and/or revised brake lamp switch service replacement part.odi is opening this pe to further evaluate this issue. | ||||||
Consumer Complaints
| Fail date | miles | occurences | Purchase date |
|---|---|---|---|
| SERVICE BRAKES, HYDRAULIC | |||
| 02/01/2013 | 3 | ||
| 2000 mercedes benz ml-430. consumer writes in regards to brake malfunction while driving vehicle. *smd the consumer discovered there was a recall on the brakes and had the issue addressed. however, she felt there was still a problem. the consumer stated abs, srs, bas, esp and ets lights illuminated on the dashboard, and the brakes locked up and the she had no control over the vehicle. some of the lights went out, while some have remained on. | |||
| 09/28/2012 | 140950 | 1 | |
| On friday (09-28-2012 02:35 pm), i was driving and about 30 miles ne of dallas, tx, i was traveling on south bound highway 75. i was in the center lane of a three lane hwy 75 south bound and i had the cruise control set at 65 mph. all the sudden, my suv started braking and i saw the speedometer drop from 65 down and i could hear my tires catching as it was braking but i did not know what was going on with my vehicle. i tried the gas pedal twice but no response and i switched on my hazard lights. luckily the minivan behind me was able to reduce speed and as i watched the speedometer needle drop below 20 mph, my suv quit breaking. i was able to operate the vehicle (per usual) and exited off the first chance i got. i pulled into a parking lot and called my mercedes mechanic asking if he knew what might have caused the problem i just experienced. i mentioned that the drivers instrument panel showed the bas/esp indicator light. my mechanic asked if my suv was working okay and if so, he recommended i turn around and head back to tulsa. i got back with no sudden breaking problems and took my suv into the shop on monday (10-01-2012 08:00 am). i got it back later that afternoon and they noted the repair reason was they had reinitialized the yaw sensor. i did a google search and found your website describing my experience exactly and i can say my sudden breaking experience was more than .03 seconds. *tr | |||
| 11/30/2006 | 95000 | 1 | 12/01/2004 |
| No matter what repair is done to front & rear brakes they will not stop squeaking. *jb | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - PADS | |||
| 08/13/2003 | 1 | ||
| Consumer stated when applying the brakes vehicle would vibrate. dealer had replaced brake pads and rotors every 5000 miles, and same problem recurring. *ak | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - ROTOR | |||
| 08/13/2003 | 1 | ||
| Consumer stated when applying the brakes vehicle would vibrate. dealer had replaced brake pads and rotors every 5000 miles, and same problem recurring. *ak | |||