Recalls
| Campaign | Manufacturer | Manufacturing date | Type | # of units affected | Date Owner notified Mfg | Recall Initiated by | Manufacturers of recalled vehicles/products | Report Recieved Date | Record Creation Date | Regulation Part Number | FMVSS Number | |||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| SERVICE BRAKES, HYDRAULIC - ANTILOCK | ||||||||||||||||
| 96V099000 | CHRYSLER CORPORATION | from 07/01/1990 to 06/01/1993 | V (Vehicle) | 321000 | 09/03/1996 | ODI | CHRYSLER GROUP LLC | 06/13/1996 | 06/18/1996 | |||||||
| Defect Summary | The abs hydraulic control unit can experience excessive brake actuator piston seal wear causing pump-motor deterioration. | |||||||||||||||
| Consequence Summary | If this condition occurs, the abs function could be lost and reduced power assist would be experienced during vehicle braking increasing the potential for a vehicle accident. | |||||||||||||||
| Corrective Summary | Dealers will test the vehicle's anti-lock brake system and repair the vehicles if necessary. also the warranty on all abs components will be extended to 10 years or 100,000 miles (except for the brake actuator piston assembly and the pump-motor assembly which will have a lifetime coverage). owners will also be reimbursed for previous abs component repair costs. | |||||||||||||||
| Notes | System: brakes; hydraulic; anti-skid system. vehicle description: passenger vehicles and mini-vans equipped with anti-lock brake systems (abs). note: owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chrysler at 1-800-853-1403. also contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393. | |||||||||||||||
Investigations
| NHTSA ID | Manufacturer | Date open | Date close | Subject | Recall campaign | |
|---|---|---|---|---|---|---|
| SERVICE BRAKES, HYDRAULIC | ||||||
| EA94028 | CHRYSLER GROUP LLC | 07/29/1994 | 06/24/1996 | ABS BRAKING SYSTEM FAILS | 96V099000 | |
| There is no summary currently available | ||||||
| PE94024 | CHRYSLER GROUP LLC | 03/07/1994 | 07/29/1994 | ABS BRAKING SYSTEM FAILS | ||
| There is no summary currently available | ||||||
Consumer Complaints
| Fail date | miles | occurences | Purchase date |
|---|---|---|---|
| SERVICE BRAKES | |||
| 04/02/2012 | 243067 | ||
| Tl* the contact owns a 1993 plymouth grand voyager. the contact stated that as he was braking to a stop, the brake pedal abnormally traveled to the floorboard causing an increase in stopping distance. the contact was able to stop the vehicle as he continued to apply the brakes. the contact referenced nhtsa campaign id number: 96v099000 (service brakes, hydraulic: antilock), stating that the vehicle was previously repaired under the recall but the failure still existed. the vehicle was taken back to the dealer who performed the recall repairs. the contact left the vehicle with the dealer and stated that the vehicle was not repaired correctly. the manufacturer was notified who advised that they would give him a return call. the failure mileage was 243,067. | |||
| 04/02/2012 | 243067 | ||
| Tl-the contact owns a 1993 plymouth grand voyager. the contact stated that as he was braking to a stop, the brake pedal abnormally traveled to the floorboard causing an increase in stopping distance. the contact was able to stop the vehicle as he continued to apply the brakes. the contact referenced nhtsa campaign id number: 96v099000 (service brakes, hydraulic: antilock), stating that the vehicle was previously repaired under the recall but the failure still existed. the vehicle was taken back to the dealer who performed the recall repairs. the contact left the vehicle with the dealer and stated that the vehicle was not repaired correctly. the manufacturer was notified who advised that they would give him a return call. the failure mileage was 243,067. kmj | |||
| 04/02/2012 | 240367 | ||
| Tl-the contact owns a 1993 plymouth grand voyager. the contact stated there was a recall nhtsa campaign id number: 96v099000: service brakes, hydraulic: antilock. the vehicle was repaired under the recall but the failure still exists. the vehicle was taken back to the dealer who repaired it again but the contact refuse to pick it up. the contact stated the vehicle was not safe and it was not repaired correctly. the manufacturer was notified who stated they will give him a return call. the failure mileage was 243,067. mw | |||
| SERVICE BRAKES, AIR - ANTILOCK | |||
| 1 | |||
| Consumer received recall 96v099000 concerning brakes:hydraulic:anti-skid system failure. dealer wanted to charge $85.00 to look at the vehicle before doing recall repairs.*ak | |||
| 08/24/2003 | 74610 | 1 | 09/09/1994 |
| Two complete abs brake failures within 3 weeks. continuous abs brake problems over the life of the vehicle. recall completed. problems persist. | |||
| 01/01/1999 | 50 | 10/01/1994 | |
| Brakes shudder when trying to stop at higher speeds above 45 miles per hour, air conditioner fan stops at speeds above 55 miles per hour when the engine begins to load going up hills before it shifts into overdrive | |||
| SERVICE BRAKES, HYDRAULIC | |||
| 06/15/2002 | 100000 | ||
| Tl*the contact owns a 1993 plymouth grand voyager. the contact stated that it is very difficult to depress the brake pedal in his vehicle. he has to use all of his strength to get them to work. in addition, the abs pump is running and will not shut off. the abs lights and brake lights are currently illuminated. the rear wiper on the rear hatch has been replaced four times at the cost of $350. the wiper currently needs to be replaced again. within six months of having the vehicle repaired, the failure recurred. the driver's side door is falling off the hinges and the door was repaired once before with a used door. the door currently needs to be repaired or replaced again. at 81,000 miles, the transmission had to be replaced due to shift bump behavior; however, the failure still persists. the air conditioner has not worked since the vehicle was purchased. the current mileage was 151,000 and failure mileage was 100,000. | |||
| 07/20/2004 | 1 | ||
| While driving the vehicle at any speed and applying the brakes, the brake pedal went to the floor with no brake at all resulting in an extended stopping distance. as a result, consumer was involved in a front end collision. dealership has been notified. please provide further information notified. *la | |||
| 08/15/2003 | 175000 | ||
| My abs light came on when driving, within seconds, i had absolutely no brakes. the dealer fixed at no charge, although i had to pay for towing. today has been 2 weeks since i've had the vehicle repaired. as i was traveling down the freeway with my 4 children, the abs light came on again, and the brakes were gone again. when i purchased this vehicle in 1999, the abs system was replaced on 3 seperate occasions for the exact same reason. each time with the guarantee that it was fixed. what will it take to have this issue resolved? the death of my children and i? i purchased this mini van for the reason of safety due to the fact that i drive with my children quite a bit. i am very unhappy with this issue. to add to the dilemma, i am currently raising my children alone due to the fact that my husband is overseas at war. with the added stress of my husband being away, i really feel the burden with my mini van is extemely uncalled for. i can no longer do the simple tasks of going to the store without feeling fear that my vehicle will all of a sudden not stop. i am just trying to get by in a safe manner while my husband is away. and this expensive vehicle made by chrysler/plymouth has failed to do this for me. your immediate response is expected! | |||
| 01/15/2003 | 0 | ||
| Air conditioner quit working, problem is evaporator under dash. repair to be $1200 estimated. fuel pump failed. paint began peeling at 40,000 miles. just finished repainting whole vehicle at own expense. both front seatbelts would not unroll and were replaced. transmission failed at 68,000 miles, dealer repaired at no charge. abs no longer works. wheels lock up when hard braking. | |||
| 08/15/2003 | 74618 | ||
| Total abs failure twice within three week period. dealer replaced pump motor under recall warranty for first failure, diagnosed dual function pressure switch for second failure. dealer and manufacturer refuses to warrant pressure switch as part of abs. pressure switch has been replaced at 40,400 miles on 3/25/97, replaced again at 68,327 miles on 5/29/01. current instance is third failure of switch. on going abs failures over life of car. | |||
| 06/17/2003 | 1 | ||
| While driving and without warning brakes failed,causing extended stopping distance. dealer notified. *ak | |||
| 05/31/1994 | |||
| The hydraulic pump failed. nlm | |||
| SERVICE BRAKES, HYDRAULIC - ANTILOCK | |||
| 06/10/2008 | 142000 | 2 | 02/06/2008 |
| Tl*the contact owns a 1993 plymouth grand voyager. the contact stated that the liftgate hinge was not operating correctly. the liftgate closed without assistance. the vehicle was taken to an independent mechanic and repaired. also, the abs warning light illuminated intermittently on the instrument panel. the contact applied pressure to the brake pedal and experienced difficulty slowing down. there was also a malfunction with the seat belt assembly buckle. recently, while driving approximately 65 mph in the rain, the windshield wipers stopped working without warning. the vehicle was taken to an independent mechanic on three separate occasions. the technician advised that the vehicle be taken to an authorized dealer. at this time, the vehicle has not been repaired. the failure mileage was 142,000 and current mileage was 155,000. update 10/01/08 *cw the set belt would not retract. updated 10/03/08. *jb | |||
| 04/14/2008 | 3 | 10/14/2007 | |
| The abs system failed three times on 4/15/08. the vehicle is a plymouth grand voyager, 1993. i almost hit a car that was turning in front of me. then the abs and parking brake lights lit up on the dash board. i barely made it home without hitting anything and parked my car in the garage. when i went out a few minutes later to take it to a mechanic nearby, the brake pedal dropped when i turned the key to start the car. the brakes were mushy until i got it to the mechanic. he confirmed the problem is with the abs system and that it was covered under the recall. the byers chrysler dealership now has the car and is claiming they cannot reproduce the problem and will not replace the abs until they can. i do not want to kill myself or anyone else with a braking system that may fail at any time. *tr | |||
| 01/01/1998 | 0 | 09/01/1993 | |
| Tl*the contact owns a 1993 plymouth grand voyager. approximately ten years ago, the contact received a recall notice for nhtsa campaign id number 96v099000 (service brakes, hydraulic:antilock)and daimler chrysler recall number 685. he took his vehicle to the dealer for service, but they could not honor the recall notice. they informed the contact that recalls could only be serviced within a reasonable amount of time. according to the contact, the recall stated that the consumer could get a free remedy any time after receiving the notice for the life of the vehicle. the service manager at the dealer agreed with the contact. the contact stated that general motors should honor what is mentioned in the recall notice. it was noticed that nhtsa's recall notice slightly differed from the manufacturer's notice concerning the services that would be provided for the life of the vehicle. the contact stated that he can provide a copy of the recall notice from daimler chrysler. there had been no failure to date. the current mileage was 92,000. | |||
| 02/01/2006 | 120000 | 50 | 10/01/2000 |
| Tl*the contact owns a 1993 plymouth grand voyager. while driving in reverse at 5 mph, the brake pedal would not depress, despite using extreme force. the contact stated that the failure was intermittent, however, the abs light remained illuminated. the mechanic diagnosed the vehicle as having antilock brake failure. the dealer stated that her vin was not included in nhtsa recall number 96v099000 (service brakes, hydraulic:antilock). the powertrain was unknown. the current mileage was 155,000 and failure mileage was 120,000. | |||
| 10/14/2006 | 96000 | 5 | 03/10/2004 |
| Dt*: the contact stated while depressing the brake pedal at various speeds, there was an increased stopping distance. the vehicle was driven to the dealer who determined the dual function pressure switch needed to be replaced. the consumer was told the dual pressure switch was apart of the abs and was not covered under any recall. the consumer was told that the pressure switch failed because the abs/pump motor had failed so many times. updated 12/01/06. *jb the stated the abs module had been replaced 5 times | |||
| 11/20/2003 | 115381 | 2 | 05/15/1993 |
| I have a 1993 plymouth grand voyager. the abs pump and motor were replaced (under warranty) with a re-manufactured unit on 11/05/01 when the vehicle mileage was 104,691. the pump just failed again, and was replaced with another re-manufactured unit. the vehicle mileage is now 115,381. i am concerned that chrysler is install poor quality repair parts under the warranty. *la | |||
| 1 | |||
| Driver had difficulty pressing the brake pedal. dealer found that the vehicle was within the remedy scope for recal 96v099000, and made the appropriate repairs. after the repairs, brake lights illuminated, and the brake pedal was still hard to push. *ak | |||
| 1 | |||
| The abs light and the park light illuminated. also, the brake pedal must be depressed all the way to the floor to get the vehicle to stop. the vehicle was not in the remedy scope for recall# 96v099000 subject: brakes:hydraulic: anti-skid system; although the vehicle experienced the same symptoms as the vehicles affected in that recall. *ak *ts *jb | |||
| 07/01/2003 | 1 | 02/01/2003 | |
| I had trouble with my anti-lock brakes on a 1993 plymouth grand voyager. i downloaded the information about the recall and made an appointment with the dealer. on the day of the appointment they had a representative of chrysler there who stated, even though there was a recall, our particular vin number was not included. they also stated they would have to charge us to fix a computer chip that was not working to test the braking system. this vehicle had over 100,000 thousand miles so we knew not all of the recall would apply, but certain components had a lifetime replacement warranty. because of the up front charges we withdrew the vehicle from the dealer and sent it to an independent garage, who is having trouble finding the used parts. the dealer said the info. on this website are just summaries and not always correct for the particular vehicle.*ak | |||
| 06/23/2003 | 1 | ||
| While traveling on the highway and without prior warning the abs braking light appeared on the dashboard. *ak | |||
| 1 | |||
| Consumer brought vehicle in for recall repairs, 96v099. mechanic informed consumer that the previous owner took care of the recall and that the problem consumer was experiencing was a sensor, which was not recall related. consumer was charged for diagnostic testing and feels this is an error since no testing was authorized. consumer requests reimbursement. *jg | |||
| 2 | |||
| Consumer states brake pedal is hard and stiff and the abs and brake light stays on. dealer found problem with hydraulic control unit which is under recall (96v099000). however, authorized dealership would not honor recall. consumer had to take vehicle to another authorized dealership that was 200 miles round trip. *tt | |||
| 1 | |||
| Prior to the recall the abs light came and took it to amoco station paid $74 and the light turned off, again the light returned and took the vehicle to the dealer and it took them two weeks to repair the modulator, the consumer is asking refund for the cost originally at the amoco station. *yh | |||
| 01/26/2002 | 4 | ||
| Vehicle was repaired under recall 96 v 099 000. since repair of vehicle brakes have failed four times, one of which resulted in a collision. when brakes were applied pedal became hard. vehicle was serviced at fresno chrysler, in fresno ca 559-225-2100. *ak | |||
| 2 | 03/07/1996 | ||
| Abs system does not operate as it should in ice and snow. pedal feels hard, vehicle taken to dealer numerous times, insists abs is working properly. consumer stated that after recall 96v099000 was performed problem had reoccurred, dealer told consumer that this condition would not fail under warranty, consumer states that recall notice 96v099000(attached) states otherwise. *ak *tt | |||
| 06/01/2001 | 0 | ||
| Consumer's vehicle was inside of a parking lot area, went to apply brakes, and there were no brakes. pedal went all the way to the floor. also, abs braking light came on dashboard. dealership was aware of problem. *ak | |||
| 1 | |||
| Prior to the recall the abs light came and took it to amoco station paid $74 and the light turned off, again the light returned and took the vehicle to the dealer and it took them two weeks to repair the modulator, the consumer is asking refund for the cost originally at the amoco station. *yh | |||
| 04/09/2001 | 0 | ||
| While driving abs light will came on, and that will indicate that brakes will not operate, leaving vehicle without brakes. *ak | |||
| 05/24/2000 | 4 | 04/19/2000 | |
| While driving down hill, brake and abs sensor becomes illuminated, brakes fade and then do not work at all, the dealer where vehicle was purchased would not do recall repairs on vehicle (96v099), however another dealership provided repairs, vehicle experiences several brake problems still, brakes are noisy, calipers have been replaced and consumer is concerned about the safety of the vehicle. *slc | |||
| 01/01/2000 | |||
| Vehicle experiencing problem with abs and brake lights remaining on when applying brakes. vehicle would not stop properly, needed to apply brakes extra hard to get vehicle to stop. dealer notified. please feel free to provide any further details on this matter. *ak | |||
| 11/23/2000 | 2 | 10/01/1993 | |
| We have had chronic problems with abs system failure over the life of the vehicle. i understood plymouth was supposed to guarantee the abs system for 100,000 miles and the pump/accumulator/master cylinder for the life of the vehicle. this is certainly not a reliably safe system. the dealer info i gave was the dealer we purchased the vehicle from. our current dealer is buzz leonard in panama city, florida 32405. *ak | |||
| 11/01/1996 | 1 | 05/01/1996 | |
| We have reported a number of times to 3 dealers that we are getting warning lights on the abs system. some have said there is no issue, the brakes will still work. the latest dealer says it is undrivable due to safety risk. | |||
| 04/01/2000 | 4 | 03/31/1993 | |
| Recall 96v099000. dealer has repaired vehicle two times under recall, and problem has reoccurred several times.*ak | |||
| 07/25/2000 | 0 | ||
| While driving abs brake light will come on unexpectedly, and brakes pedal will be hard, even at times had to step on brakes with both feet.*ak | |||
| 07/06/2000 | 4 | 07/01/1993 | |
| I have had trouble with the abs since i bought the car. the system has been replaced 3 times to date and is now beginning to fail once again. i have had numersous repairs to the a/c system. thew first was in 1996 ($472). the second in 1998 ($850). the third also in 1998 ($286). the fourth again in 1998 ($673). the fifth in 1999 ($178). the sixth in 2000 ($688). so, to date, i have spent over $3000.00 having the a/c repaired on this vehicle. the frequency of repairs and the amount paid for these repairs is unacceptable and suggests that there is a major problem with this component that should be the responsibility of the manufacturer. to summarize, i have had frequent and excessive problems with both the abs and a/c systems. thank you for you attention. | |||
| 4 | 03/01/1999 | ||
| Nhtsa campaign id# 96v099000 (mfg. campaign #685) - contact with chrysler plymouth indicates that the vin# for this vehicle is not included in this recall even though this vehicle experiences the same problems as identified in the recall. can you help us persuade chrysler plymouth that this vehicle vin# should be included in the recall so that we may have the problems repairs & obtain reimbursement for previous repairs already performed?*ak | |||
| 01/01/1998 | |||
| There was a manufacturer's recall 05685184 on the anti-lock brake system . consumer was traveling about 25 to 30mph on the highway, she applied brakes, the pedal was very hard, and brakes failed. *ak | |||
| 02/16/2000 | 0 | ||
| Exciter rings are cracked, causing abs to become engaged. consumer says the cure would be to replace both front axles. *ak | |||
| 08/18/1998 | 2 | 05/31/1994 | |
| Dual pressure switch failed causing the abs light to illuminate. nlm | |||
| 07/01/1998 | |||
| Recall 96vo00000/abs: on jan 97 vehicle been serviced for manufacturer's recall. as of the incident date vehicle has been experiencing ongoing/intermittent problem with abs light coming on, and brake pedal pulsating when applying brakes. when this occurred, it resulted in extended stopping distance. dealer notified. but, problem is still occurring. *ak | |||
| 8 | |||
| Abs continually malfunctions causing eight near accidents due to failure. mjs | |||
| 5 | |||
| Prior to recall brake system failed (96v-099).after replaced, the brake system failed again. yh | |||
| 3 | 07/01/1993 | ||
| I have had the anti-lock brakes replaced 3 times. the first time was prior to the recall on the abs system. i am wondering if anyone does follow-up on the recalls to see how often a replacement part itself needs to be replaced. i believe that 3 replacements of a particular component in 5+ years (7/1993-11/1998) is excessive. *ak | |||
| 1 | |||
| Abs failed after being fixed for recall. yh | |||
| 1 | |||
| Pump motor running continously instead of cycling and holding. yh | |||
| 09/09/1999 | 5 | 01/01/1993 | |
| Consumer was driving on wet pavement and applied brakes, and the brakes locked up. also abs brake light pops up on the dashboard. *ak | |||
| 3 | |||
| The brake system has been recalled due to a failure in the anti lock system. the dealer has replaced this system at least 3 times, when it fails ( without warning) the pedal pushes extremely hard, and you have only very limited braking ability. the dealer has told us that the brakes will be warrenteed for the life of the vehicle. this gives me a sick feeling knowing the history of this vehicle. *ak | |||
| 5 | |||
| Vehicle has been repaired under recall #96v099, anti skid brake system. since the initial repair under the recall, vehicle has been to the dealership for repair service five times . consumer states that when the brakes are applied, pedal becomes hard, resulting in extended stopping distances. the manufacturer has been notified. *ak | |||
| 07/06/1996 | 3 | 12/01/1993 | |
| First abs diagnosis of 7/6/96 cost us $57.68. parts ordered. 7/31/96 parts installed cost $50. 9/25/98 problem returned though passed inspection. 12/11/98 problem returned-actuator replaced (no cost). 7/26/99 problem returned-abs module replaced $317.00. 7/27/99 problem returned-diagnosis of pump/motor code failure with est. cost $385. | |||
| 02/05/1999 | 5 | ||
| Abs brakes had failed. the abs brake light came on. had a panic stop. vehicle failed to stop. pedal was hard. down shifted to low & applied emergency brakes. took to dealer for problem. nothing found. a contiuous problem, but intermittent. *ak | |||
| 12/30/1997 | 2 | ||
| Anti lock brake dual pressure switch failed, abs continued to experience problems prior to recall notice, however dual pressure switch is not included in the recall. | |||
| 2 | 07/01/1993 | ||
| Anti lock brakes still experience intermittent failure even though recall repair work on abs system was completed. | |||
| 1 | |||
| Abs system fails intermittantly. | |||
| 08/26/1998 | 2 | 08/01/1993 | |
| I previously submitted a hard copy of the original failure (nhtsa reference number 828479) via normal mail. this submission is to document a similar safety issue that occurred 7 weeks after the original problem was 'fixed'. i will repeat the information from my original submission for reference. original submission (10/22/98): i had a recall performed on the abs system in 1996. at that time, i was under the impression that a defective designed part was being replaced with a newer designed part and that the abs system would now function properly. in august of 1998, while driving down a road at 35 mph, i attempted to brake and had no brakes at all. fortunately, no accident occurred. i took the vehicle to spartan chrysler plymouth in murray, ut who informed me the abs hydraulic system 'piston assembly' had failed. they indicated that this was the same part for which the recall was issued in 1996. they told me (in 1998) that in 1996 the recall only consisted of checking the part to see if it was bad. my question is that i wonder if the recall was really just to check the part? this seems like a serious safety problem. the part can work today and pass the recall 'test' only to fail tomorrow and cause injury or death because the vehicle loses the braking system. wouldn't it be safer to remove the fauly designed part and replace it with a known fixed part? update (11/18/98) on 7 november, the braking system of my vehicle failed with identical symptoms as before. without warning, there was no braking system in the vehicle. again, we were fortunate to not cause and accident. i returned the vehicle to the same spartan dealership. this time they diagnosed the problem as a failed 'accumulator pump' in the abs system. they insist the two failures (2 months apart) are totally unrelated, that there is no history of abs failures in this model of van, and that there is no underlying problem which is causing these parts to fail. the vehicle was repaired on 1 | |||
| 08/01/1997 | |||
| Since abs recall 685 has been done, the brakes have been irregular. the pedal fights me, the pedal locks up and the abs system is obviously mechanically compromised. dealer totally unable to address my numerous complaints. (they claim i dont no how to brake) | |||
| 1 | |||
| Recall work completed on the anti lock brake system, however problems continue. | |||
| 09/26/1998 | |||
| Had received recall notice (96v099000). called dealer. took vehicle to dealer for repairs. told vehicle ready for pick up. after picking up vehicle, short time later, brake system failed to work properly after being applied. an accident happened due to brake failure. *ak | |||
| 08/01/1998 | 1 | 08/01/1993 | |
| Received recall notice (96v099000). called dealer. took vehicle on appointed day for repairs. later, was informed vehicle was ready & repairs done. sometimes later, was driving vehicle when brake system failed due to a lack of braking power. *ak | |||
| 07/17/1998 | |||
| When brakes were applied the pedal went to the floor, resulting in extended stopping distance. manufacturer and dealer have been notified. *ak | |||
| 05/27/1998 | 4 | ||
| 96v099000. consumer states that the brakes have been repaired about four times and the problem still remains, just received recall information, contacted the dealer to remedy the problem, remains on hold until the repair work can be done for the fifth time. *ak | |||
| 06/06/1997 | 3 | ||
| Abs brake problems; on normal road conditions when applying the brakes, it appears that the system is trying the work. the pedal goes to the floor, and the van requires additional stopping distance. taken to dealer at least (3) times. dealer not able to locate problem. two weeks ago while driving the vehicle, the brakes gave out completely. problem has been corrected by dealer.*ak | |||
| 02/16/1998 | 1 | ||
| While driving abs brake warning light came on/off and abs brakes failed. had difficulty stopping vehicle. *ak | |||
| 02/16/1998 | |||
| Abs brake failure prior to recall, recall repairs refused because no specific problem was found regarding the abs brakes (96v-099). *ak | |||
| 02/03/1994 | |||
| Brake pedal buzzes when applied, abs warning light comes on, possible due to abs recall. | |||
| 1 | 05/01/1996 | ||
| Abs brake problems. | |||
| When the brakes were applied, the abs light came on and the pedal went to the floor , resulting in extended stopping distance. the dealer is inspecting the vehicle. *ak | |||
| 0 | |||
| When the anti lock brakes are applied, the pump makes a loud buzzing sound. | |||
| While driving and when attempting to slow/stop, brake action seemed inadequate to effectively stop, vehcile continued to roll forward 3-4 feet before stopping, also, noticed when braking a loud grinding noise, not fixed. *ak | |||
| Vehicle experiences excessive failure of abs pump. *ak | |||
| Owner has abs brakes, she states that her brakes lock up and that this is an intermittent problem which caused owner to have an accident. dealers told owner abs brakes do not work in dry wheather. *ak | |||
| 12/06/1996 | 1 | 08/01/1993 | |
| Antilock brakes failed, causing accident/injury. | |||
| 07/01/1996 | 1 | 01/21/1993 | |
| Abs failed due to leaking abs pump. *dh | |||
| 02/27/1996 | 1 | 02/01/1996 | |
| Antilock brake hydraulic pump/accumulator failed, causing brake failure. | |||
| 01/12/1996 | 3 | ||
| Antilock brake system failed three times. | |||
| SERVICE BRAKES, HYDRAULIC - ANTILOCK - CONTROL UNIT/MODULE | |||
| 06/16/1995 | 1 | 01/21/1993 | |
| Abs warning light came on due to failed left wheel sensor. *dh | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS | |||
| 10/15/2001 | 1 | ||
| Consumer states while driving brake failed to stop and vehicle was involved in an accident, the air bag did not deploy (claim# 27-7050-482). *yd | |||
| 05/24/2000 | 4 | 04/19/2000 | |
| While driving down hill, brake and abs sensor becomes illuminated, brakes fade and then do not work at all, the dealer where vehicle was purchased would not do recall repairs on vehicle (96v099), however another dealership provided repairs, vehicle experiences several brake problems still, brakes are noisy, calipers have been replaced and consumer is concerned about the safety of the vehicle. *slc | |||
| 06/17/1997 | |||
| Recall # 96v099000, dealer states that brake fluid is not covered under warranty and does not want to service without charge. brake fluid is contaminated. owner states that fluid was contaminated by dealer. | |||
| 11/14/1996 | |||
| After being checked under recall, owner is sitll experiencing a problem with the brake system, dealer cannot find a problem with the vehicle. dealer never bothered to check vehicle for problem. #685. *ak | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC | |||
| 06/18/1996 | 1 | 04/01/1993 | |
| Front rotors warped/brakes replaced. | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - PADS | |||
| 11/23/2000 | 4 | 10/01/2000 | |
| Replaced brake hydrualic system and all pads,shoes.still not working right! | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - ROTOR | |||
| 06/18/1996 | 1 | 04/01/1993 | |
| Front rotors warped/brakes replaced. | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - MASTER CYLINDER | |||
| 09/08/2000 | 4 | 04/24/1993 | |
| Consumer has experienced numerous problems with leakage of master brake cylinder fluid. the problem has been on going since september of 98. the master clylinder brake cap was replaced and the system has been judged as ok by the dealership under recall 96v099000 but the problem continues. *cj | |||
| SERVICE BRAKES, HYDRAULIC - PEDALS AND LINKAGES | |||
| 2 | 03/07/1996 | ||
| Abs system does not operate as it should in ice and snow. pedal feels hard, vehicle taken to dealer numerous times, insists abs is working properly. consumer stated that after recall 96v099000 was performed problem had reoccurred, dealer told consumer that this condition would not fail under warranty, consumer states that recall notice 96v099000(attached) states otherwise. *ak *tt | |||
| 1 | |||
| Vehicle makes electronic clicking noise when brakes pedal is depressed. yh | |||
| SERVICE BRAKES, HYDRAULIC - POWER ASSIST | |||
| 11/23/2000 | 4 | 10/01/2000 | |
| Replaced brake hydrualic system and all pads,shoes.still not working right! | |||
| SERVICE BRAKES, HYDRAULIC - SWITCHES - BRAKE WARNING | |||
| 06/20/1998 | |||
| Abs and brake warning light remain on approx. 2 min. after starting vehicle. | |||
| 06/20/1998 | |||
| Abs and brake warning light remain on for approx. 2 minutes after starting vehicle. | |||