Recalls
| Campaign | Manufacturer | Manufacturing date | Type | # of units affected | Date Owner notified Mfg | Recall Initiated by | Manufacturers of recalled vehicles/products | Report Recieved Date | Record Creation Date | Regulation Part Number | FMVSS Number | |||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| SERVICE BRAKES, HYDRAULIC - ANTILOCK | ||||||||||||||||
| 96V074000 | CHRYSLER CORPORATION | from 08/01/1994 to 08/30/1995 | V (Vehicle) | 90000 | 07/08/1996 | MFR | CHRYSLER GROUP LLC | 05/02/1996 | 05/03/1996 | |||||||
| Defect Summary | Corrosion of the abs hydraulic control unit can cause the solenoid valves to stick in the open position. | |||||||||||||||
| Consequence Summary | If either front wheel valve sticks, the vehicle would swerve from a straight stop when the brakes are applied. | |||||||||||||||
| Corrective Summary | Dealers will install a plate and silicone grease injected into the solenoid cavity to eliminate the potential for this condition. | |||||||||||||||
| Notes | Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time, should contact chrysler at 1-800-853-1403.also contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393. | |||||||||||||||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - MASTER CYLINDER | ||||||||||||||||
| 96V075000 | CHRYSLER CORPORATION | from 08/01/1994 to 10/01/1995 | V (Vehicle) | 151800 | 06/10/1996 | MFR | CHRYSLER GROUP LLC | 05/03/1996 | 05/08/1996 | |||||||
| Defect Summary | The brake master cylinder can leak brake fluid due to a damaged double lip rear piston seal. | |||||||||||||||
| Consequence Summary | Brake fluid leakage can result in diminished effectiveness of one half of the split brake system. the instrument panel warning light(s) will signal system impairment prior to partial brake system loss. | |||||||||||||||
| Corrective Summary | Dealers will replace the rear brake master cylindr piston assembly. | |||||||||||||||
| Notes | System: brakes; hydraulic; master brake cylinder. vehicle description: passenger vehicles. includes neon vehicles equipped with the acr competition package only. note: owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time, should contact chrysler at 1-800-853-1403. also contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393. | |||||||||||||||
Consumer Complaints
| Fail date | miles | occurences | Purchase date |
|---|---|---|---|
| SERVICE BRAKES, AIR - DISC - ROTOR | |||
| 12/18/1995 | |||
| Both a 3rd party inspection station and the dealer mechanic acknowledge that the front rotors on this vehicle are pitted...in manufacture...at an 'unreasonably' premature lifespan...23k miles. since chrysler does not participate in the bbb lemon law arbitration...their direct contact 1-800-992-1997 maintained the warranty of 1yr/12k miles...disregarding the supporting evidence from the above sources that the pitting was a manufacturing flaw...and therefore clearly the responsibility of chrysler to replace...at no cost. | |||
| SERVICE BRAKES, HYDRAULIC | |||
| 11/21/2002 | 71980 | 3 | 12/31/1996 |
| The rear brake hose collapsed from excessive hardware dust, which caused the rear wheel cylinder to leak, the rear brakes were replaced, the master cylinder was replaced under recall, however it had to be replaced a second time. ts *jb | |||
| 10/29/2002 | |||
| While driving, upon applying brakes to make a gradual stop the brakes failed to respond. vehicle would need an extended stopping distance. vehicle was involved in a crash. consumer has contacted the dealer which determined that the front brake rotors were the incorrect size causing the problem. front brake rotors were replaced. ts | |||
| SERVICE BRAKES, HYDRAULIC - ANTILOCK | |||
| 02/23/2004 | 60000 | 6 | 10/15/1996 |
| Loss of abs when applying brakes. this happens at all levels of braking, i.e. heavy, medium and minimal braking. when loss of abs happens, the pedal decends to the floor and a buzz/racheting noise is heard. this problem has lead to potentially 4 major accidents. to solve the loss of braking, driver has to re-pump the pedal after loss has occured. (no mil/scan tool code recorded) . *ak | |||
| 02/20/2001 | 0 | ||
| Abs brakes locked up, causing vehicle to slide.*ak | |||
| 09/01/2000 | |||
| Consumer was traveling about 35mph on a highway street, and went to apply brakes and pedal went all the way to the floor. he passed the stop sign, there were no brakes. then, as he rode down the street, three blocks later the brakes came back and the emergency brakes handle was up.*ak | |||
| 01/01/1997 | 12/01/1996 | ||
| At 55,000 miles the abs light came on on my vehicle's instrupment panel.upon taking same to a certified mechanic i was advised that the abs motor was no longer working however the vehicle brakes them selves were in working order. i contacted chrysler and was advised that my vehicle was not on the recall list as other 1996 2.5 liter chrysler cirrus(s) were for their abs master cylinder piston (recall#686) and master cylinder primary piston(recall#687). at 75,000 miles i was exiting off of interstate i-95 onto i-395 when i attempted to brake for a traffic signal(red light) the abs light which normally stayed lit constantly began to flicker/blink . while my foot was pushing the brake pedal the pedal began to pulsate and pushed up. the vehicle was unable to stop and i was headed into an intersection when i steered the vehicle into a high curb symotaniously shifting the vehicle into park to avoid colliding into any vehicles at the intersection(conway st. and i-395). the vehicle was towed to my mechanic where the front driver's side tire and wheel/rim was replaced .the mechanic advised he was unable to locate the reason forthis incident. the fuse to the abs motor located in the fusebox under the hood was removed to ensure same incident would not occur again. i am giving you this information not for restitution but to investigate why no recall was issued for my and maybe other chrysler cirrus(s) vehicles. sincerely, franklin lee adkins. *ak | |||
| When applying the abs brakes the steering wheel vibrates, cause unkown. also, the abs warning light illuminated, indicating malfunction. dealer replaced the relay pump. please give any other details. *ak | |||
| 1 | 05/24/1996 | ||
| Abs brakes have a tendency to fade, also grind in panic stops. | |||
| 01/26/1997 | 02/27/1996 | ||
| Experienced total brake failure prior to/after recall repairs (96v075/074). *ak *ak | |||
| 12/30/1996 | 3 | 04/18/1996 | |
| Abs brakes failed 3 times, brake pedal dropped almost to the floor and felt spongy for a little while. *ak | |||
| 10/20/1996 | 1 | ||
| The master cylinder is empty because there's a crack in it which caused a complete brake failure. the pedal goes to the floor before the vehicle is stopped. *ak*jb | |||
| 04/13/1996 | |||
| Abs; the front brakes are grinding metal to metal, have to start stopping ahead of time to make sure you are going to stop, 3rd time in the shop for brakes. *ak | |||
| Equipped w/abs brakes; when brakes are applied the pedal descends to floor then returns to normal. problem unknown w/dealership not able to duplicate. *ak | |||
| SERVICE BRAKES, HYDRAULIC - ANTILOCK - CONTROL UNIT/MODULE | |||
| 12/01/2002 | 16000 | 1 | |
| When consumer applied the brakes suddenly to avoid a collision, the brakes locked up which caused vehicle to skid. vehicle had been checked by 2 dealers and an independent mechanic who have all confirmed the hydraulic control unit had failed. ts *jb | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS | |||
| When driving on wet pavementand upon depressing brake pedal to make a sudden stop, consumer heard noise coming from the brakes, and there was extended stopping distance. also, in order to stop alot of force had to be applied to brake pedal. consumer has contacted the dealer . please provide any further details. *ak | |||
| Brake pedal failed went all the way to the floor. contacted dealer and manufacturer. *ak | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC | |||
| 04/01/1998 | 1 | 04/01/1996 | |
| Brake pads wore out prematurely at 36,000 miles which ruined rotors - $350 repair. car stalls when slowing - not able to identify problem. air conditioning compressor failed at 57,000 miles - $1100 repair. | |||
| 3 | 05/01/1996 | ||
| Brakes continually degrate, and steering shakes when braking at speeds over 50 mph. brakes, linings, pads, rotors replaced/resurfaced 3 times. *ak | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DISC - PADS | |||
| 11/01/1996 | 2 | 04/01/1995 | |
| Premature wea rof front brake pads. *ak | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM | |||
| 09/24/2004 | 45000 | 2 | |
| After having the front brake pads replaced emergency brake locked and melted the brake drum without being engaged. while driving a passing motorist noticed fire coming from the rear of the vehicle and notified the consumer. emergency braking system and drums had to be replaced. the cause of the failure was undetermined. *ak | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - DRUM - SHOES/LININGS | |||
| 3 | 05/01/1996 | ||
| Brakes continually degrate, and steering shakes when braking at speeds over 50 mph. brakes, linings, pads, rotors replaced/resurfaced 3 times. *ak | |||
| SERVICE BRAKES, HYDRAULIC - FOUNDATION COMPONENTS - MASTER CYLINDER | |||
| Hydraulic master cylinder is leaking brake fluid onto rear brake pads which causes squeaking noise when brakes are applied. please provide further details.*ak | |||
| 08/02/1996 | 7 | ||
| Recall no-96v075000. was fixed on 8-2-96. the master cylinder is still leaking. *ak consumer states dealer has checked 5 times and master cylinder is still leaking. *slc | |||
| 10/20/1996 | 1 | ||
| The master cylinder is empty because there's a crack in it which caused a complete brake failure. the pedal goes to the floor before the vehicle is stopped. *ak*jb | |||