Recalls
| Campaign | Manufacturer | Manufacturing date | Type | # of units affected | Date Owner notified Mfg | Recall Initiated by | Manufacturers of recalled vehicles/products | Report Recieved Date | Record Creation Date | Regulation Part Number | FMVSS Number | |||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| STEERING - WHEEL AND HANDLE BAR | ||||||||||||||||
| 96V229000 | CHRYSLER CORPORATION | from 01/01/1991 to 06/30/1992 | V (Vehicle) | 675000 | 12/27/1996 | ODI | CHRYSLER GROUP LLC | 11/18/1996 | 11/27/1996 | |||||||
| Defect Summary | The steering wheel armature stamping can crack and separate from the center hub attachment to the steering column. | |||||||||||||||
| Consequence Summary | If the steering wheel separates from the center hub attachment to the steering column, loss of control can occur increasing the risk of an accident. | |||||||||||||||
| Corrective Summary | Dealers will inspect the steering wheel for armature cracks in the center hub attachment area. any steering wheels showing cracks will be replaced. all other vehicles will have a reinforcement plate installed to prevent steering wheel separation in the event cracking occurs. | |||||||||||||||
| Notes | Owner notification began december 27, 1996. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chrysler at 1-800-853-1403.also contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393. | |||||||||||||||
Investigations
| NHTSA ID | Manufacturer | Date open | Date close | Subject | Recall campaign | |
|---|---|---|---|---|---|---|
| STEERING | ||||||
| EA95029 | CHRYSLER GROUP LLC | 09/26/1995 | 11/13/1996 | STEERING WHEEL SEPARATION | 96V229000 | |
| Alleged steering wheel separation from the steering shaft while operating the vehicle. | ||||||
Consumer Complaints
| Fail date | miles | occurences | Purchase date |
|---|---|---|---|
| STEERING | |||
| 02/19/2006 | 1 | 06/09/2005 | |
| 1992 dodge plymouth grand voyager le the steering wheel broke up under the van while i was driving,causing me to crash into some one else vehicle.*jb | |||
| 09/15/2003 | 0 | ||
| I would like to know more about the recalls for the above vehicle and what exactly they cover and don't cover and i go about getting them fixed. my car is now in the shop for failure of brakes. while i was out driving the brakes suddenly went on me | |||
| 08/06/1997 | |||
| Bill bull chysler dodge dealer will not make an appointment to fix this consumer's vehicle under recall. please descirbe details. *ak | |||
| 05/23/1997 | 0 | ||
| While driving down road looked ahead at traffic, had stopped, applied brakes but vehicle began to slow down, but did not stop. it never came to a complete stop. brakes and steering locked and consumer hit auto in front of her, causing 3 persons and herself to be injured and taken to hospital. *ak | |||
| 03/21/1997 | 1 | 10/01/1995 | |
| Poor steering radius due to design. | |||
| STEERING - HYDRAULIC POWER ASSIST - PUMP | |||
| 12/03/1998 | |||
| Immediately after starting the van, pulling away from a parking place, driver found the van difficult to steer. when checking under the hood husband found the belt tensioner broke. dealership contacted about the problem. the problem has not been corrected. *ak | |||
| 08/05/1995 | 3 | 06/19/1992 | |
| While driving the vehicle on the highway, the tensioner fell out onto the highway and the fan belt cracked, causing the truck to loose power steering without any warning. *ak consumer stated the belt tensioner failed 3 times and had to be replaced, consumer stated the bolt that holds the tensioner to the engine block vracked.*jb | |||
| STEERING - LINKAGES - TIE ROD ASSEMBLY | |||
| 02/19/2006 | 1 | 06/09/2005 | |
| 1992 dodge plymouth grand voyager le the steering wheel broke up under the van while i was driving,causing me to crash into some one else vehicle.*jb | |||
| STEERING - RACK AND PINION | |||
| 09/29/2000 | 9000 | 1 | 02/01/2000 |
| I was making a slow 90 degree turn to the right onto a driveway which was approximately 12 lower than the road i was on. as my right wheel dropped off onto the driveway, we heard a sharp cracking noise. shortly thereafter, i noticed that the steering was stiff when turning to the right. it was the next day , sunday when as i turned to the right, we lost all our power steering fluid with a gush as the power steering pump blew its front main seal due to over pressuring from the broken rack and pinion. the rack and pinion main shaft was completely severed, it actually tore off its welded bracket on one side and the hydraulic cylinder which was a componet of the system, bound up and blew out both seals. the mechanic indicated that this lead to the over pressure of the power steering system which resulted in the pump blowing its main seal. he also said he felt the design of the system )ie not having both sides of the rack and pinion in hard mounts) was at least a partial cause. additionally, the mechanic indicated that the re-builder to whom this was to be sent had seen about 10 others like this previously. had a total cost of repair was almost $1,000.00. *jb ***dimsii ivoq entry posted after 12/12/02 cut-over to artemis*****734343 | |||
| 09/29/2000 | 1 | 02/01/2000 | |
| I was making a slow 90 degree turn to the right onto a driveway which was approximately 12 lower than the road i was on. as my right wheel dropped off onto the driveway, we heard a sharp cracking noise. shortly thereafter, i noticed that the steering was stiff when turning to the right. it was the next day, sunday, when as i turned to the right, we lost all our power steering fluid with a gush as the power steering pump blew its front mainseal due to overpressuring from the broken rack and pinion. the rack and pinion mainshaft was completely severed, it actually tore off its welded bracket on one side and the hydraulic cylinder which was a component of the system, bound up and blew out both seals. the mechanic indicated that this lead to the overpressure of the power steering system which resulted in the pump blowing its mainseal. he also said he felt that the design of the system(ie. not having both sides of the rack and pinion in hard mounts)was at least a partial cause. additionally, the mechanic indicated that the rebuilder to whom this was to be sent had seen about 10 others like this previously. had atotal cost of repair was almost $1,000.00 | |||
| 02/18/2001 | 1 | 02/01/1992 | |
| A grinding noise was heard when the steering wheel was turned. upon investigation, i notice the rack and pinion was moving. when i tried to tighten the bolt it snapped with little tension. looking at the bolt you can see the bolt was shearing. the bolt is approximately 10mm. it had sheared to about 2mm which snapped when i tried to tighten.*ak | |||
| 09/29/2000 | 1 | 02/01/2000 | |
| I was making a slow 90 degree turn to the right onto a driveway which was approximately 12 lower than the road i was on. as my right wheel dropped off onto the driveway, we heard a sharp cracking noise. shortly thereafter, i noticed that the steering was stiff when turning to the right. it was the next day, sunday, when as i turned to the right, we lost all our power steering fluid with a gush as the power steering pump blew its front mainseal due to overpressuring from the broken rack and pinion. the rack and pinion mainshaft was completely severed, it actually tore off its welded bracket on one side and the hydraulic cylinder which was a component of the system, bound up and blew out both seals. the mechanic indicated that this lead to the overpressure of the power steering system which resulted in the pump blowing its mainseal. he also said he felt that the design of the system(ie. not having both sides of the rack and pinion in hard mounts)was at least a partial cause. additionally, the mechanic indicated that the rebuilder to whom this was to be sent had seen about 10 others like this previously. had atotal cost of repair was almost $1,000.00 | |||
| STEERING - WHEEL AND HANDLE BAR | |||
| 04/24/2000 | 1 | 01/01/1999 | |
| While traveling and without indication steering wheel fell out into consumer's hands. dealer/manufacturer have been notified. chrysler has provided no help. *ak *ml | |||
| Steering column causes problems with starting of vehicle. also steering wheel column locks up while driving. cause unkown. | |||