International 4200 2007

Model 4200 made in 2007 by International got 2 recalls as well as 4 service bulletins. Technical service bulletines regarding electrical system and engine and engine cooling. There were some recalls concerningsuspension and vehicle speed control.

Model 2007

Recalls


CampaignManufacturerManufacturing dateType# of units affectedDate Owner notified MfgRecall Initiated byManufacturers of recalled vehicles/productsReport Recieved DateRecord Creation DateRegulation Part NumberFMVSS Number
SUSPENSION - REAR - AXLE - NON-POWERED AXLE ASSEMBLY
07V179000INTERNATIONAL TRUCK & ENGINE CORPORATIONfrom 11/15/2006 to 02/19/2007V (Vehicle)117205/18/2007MFRNAVISTAR, INC04/24/200704/25/2007
Defect SummaryOn certain trucks, one or both rear axle housings may contain thinner material than what is necessary for normal vehicle operation. over time, this thinner material may result in a fatigue failure of the rear axle housing, possibly in the location of the brake flange.
Consequence SummaryA crack in the brake flange location of the rear axle housing may result in a wheel end lockup or wheel separation possibly resulting in property damage, personal injury, or death.
Corrective SummaryDealers will inspect the vehicle's rear axles and, if necessary, replace the axle housings. the recall began on may 18, 2007. owners may contact international at 1-800-448-7815.
NotesInternational recall no. 07505.customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov.
VEHICLE SPEED CONTROL
10V267000NAVISTAR, INCfrom 12/04/2001 to 12/14/2009V (Vehicle)2085MFRNAVISTAR, INC06/15/201006/16/2010
Defect SummaryNavistar is recalling certain model year 2003 through 2010 international trucks and ic commercial buses manufactured from december 4, 2001 through december 14, 2009 equipped with international vt365 engines having engine calibration pan2pvr0, pan2pvr1, or pan2pwr. the engine normally responds to a failed open accelerator position sensor circuit fault by returning the engine to low idle speed of 800 rpm and disabling the driver's ability to increase the engine speed. however if the open circuit corrects itself within 30 seconds of initiation, engine speed could suddenly increase to a high idle speed of 1200 rpm.
Consequence SummaryThis increase to high idle speed may occur without warning causing a sudden and unexpected shift in vehicle position possibly resulting in property damage, personal injury, or death.
Corrective SummaryNavistar will notify owners and dealers will repair the vehicles free of charge. the safety recall is expected to begin on or about august 16, 2010. owners may contact navistar at 1-800-448-7825.
NotesNavistar's campaign number is 10512.owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to http://www.safercar.gov .

Bulletins


BulletinBulletin dateReplacement BulletinItem no.SummaryAdded
ELECTRICAL SYSTEM
IK080013103/12/200810025548Lose all of gauges when hooked up with dlb. applies to all vehicles with esc's or bc's. *pe08/19/2008
ELECTRICAL SYSTEM - WIRING
AFC-0890102/01/200810032925Navistar: hydraulic full power brake system power supply. installing an additional wiring harness from the positive post of the alternator to the full power brake wiring harness for the purpose of supplying redundant electrical power to t06/14/2010
ENGINE AND ENGINE COOLING - ENGINE - DIESEL
AFC-0990911/01/200910032608International: improved engine recalibration for certain bus and truck models built with maxxforce 7 engines. excessive regeneration due to certain unique driving conditions may result in fuel dilution in the target vehicles. the softwar04/19/2010
SERVICE BRAKES, HYDRAULIC - POWER ASSIST - HYDRAULIC
AFC-0890102/01/200810032925Navistar: hydraulic full power brake system power supply. installing an additional wiring harness from the positive post of the alternator to the full power brake wiring harness for the purpose of supplying redundant electrical power to t06/14/2010